360°Complete 8975 - Shaver BRAUN - Free user manual and instructions

USER MANUAL 360°Complete 8975 BRAUN

off oil fixonoff fix

• When charging for the first time: Using the special cord set, connect the shaver to an electrical outlet. The shaver must be switched off. Charge it for at least 4 hours (special cord set and shaver might get warm). Once the shaver is completely charged, shave until fully discharged. Then recharge to full capacity again (1 hour).

• A full charge will give up to 50 minutes of cordless shaving time, depending on your beard growth. However, the maximum battery capacity will only be reached after several charging/discharging cycles.

• Best environmental temperature range for charging is from 15 °C to 35 °C.

• When fully discharged, you may also shave with the shaver connected to an electrical outlet via the special cord set.

English 5647453_8975_70_S4-74 Seite 8 Dienstag, 7. März 2006 12:27 129 Indicator lights Pilot light (11): The shaver is connected to an electrical outlet. Model 8975: When the shaver is fully charged, all five charging lights (7) will light up (20% per light), provided the shaver is connected to an electrical outlet or switched on. Model 8970: The green single charging light (7) shows that the shaver is being charged. When fully charged, the charging light flashes or goes off. If later on, the charging light comes on again, this indicates that the shaver is being recharged to maintain its full capacity. The red low charge light (8) flashes when the battery capacity has dropped below 20%, provided the shaver is switched on. The remaining capacity will then be sufficient for 2 to 3 shaves. Shaving Switch positions off = (switch is locked) Press and push up the switch to operate the shaver: on = Shaving with the pivoting head (the pivoting cutting system automatically adjusts to every contour of your face). fix = Shaving with the pivoting head locked at an angle (to permit shaving in difficult areas, e.g. under the nose). trim= The long hair trimmer is activated (for trimming sideburns, moustache and beard).

5647453_8975_70_S4-74 Seite 9 Dienstag, 7. März 2006 12:27 1210 Cleaning Never use water to clean the shaver. For easy cleaning after each shave, switch the shaver off. Press the release buttons to lift the shaver foil (do not remove the foil completely). Switch on the shaver for approx. 5–10 seconds so that the shaved stubbles can fall out. Then remove the shaver foil and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. However, do not clean the shaver foil nor the cutter block with the brush as this may damage them. Keeping your shaver in top shape

About every four weeks, clean the cutter block with Braun cleaning agents. Put a drop of light machine oil onto the long hair trimmer and the shaver foil.

Replacement light for shaving parts / Reset To maintain 100% shaving performance, replace your foil and cutter block, when the replacement light for shaving parts (9) comes on (after about 18 months) or when worn. Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil and cutter block: 8000 series) The replacement light will remind you during the next 7 shaves to replace the shaving parts. Then the shaver will automatically reset the display. Tips for the perfect shave

• We recommend that you shave before washing, as the skin tends to be slightly swollen after washing.

• Hold the shaver at right angles (90°) to the skin. Stretch your skin and shave against the direction of beard growth.

• To maintain 100% shaving performance, replace your foil and cutter block, when the replacement light (9) comes on (after about 18 months), or when worn. fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix

off oil fixonoff fix