IAN 285602 - Lighting Livarno Lux - Free user manual and instructions

Product type	LED floor lamp
Brand	Livarno Lux
Model	IAN 285602
Reference numbers	14101902L or 14102002L
Operating voltage	230-240 V~, 50 Hz
LED power	2 x 5 W (non-replaceable LED modules)
Rated current	39 mA
Power factor	0.54
Protection class	II
Power supply	Mains via plug
Control	ON/OFF switch on the reflector
Height adjustment	Yes, via fixing tube
Reflector orientation	Swivelling
Arm orientation	Swivelling (with position lever on model 14102002L)
Usage	Indoor, dry and enclosed rooms
Dimmer compatibility	Not compatible
Base	Included, screw-on
Package contents	Floor lamp, base, adjustment lever, counterweight (depending on model), user manual
Maintenance	Dry, lint-free cloth; do not use water or solvents
Safety	Disconnect before maintenance; do not cover; do not look directly at the light source
Warranty	36 months
Customer service	Tel: [phone], Email: [e-mail]
Weight	Approx. 4 kg (estimate)
Dimensions (approx.)	Max height approx. 180 cm, base diameter approx. 30 cm

Frequently Asked Questions - IAN 285602 Livarno Lux

How to assemble the Livarno Lux IAN 285602 floor lamp?

Unfold the floor lamp, remove the transport locks from the vertical tube. Insert the upper part of the tube into the lower part, pull the mains cable, screw the tube onto the base and fix the adjustment lever on the reflector. Then plug in the mains plug.

How to adjust the height of the floor lamp?

First unplug the mains plug. Loosen the fixing tube, adjust the desired height, then retighten the tube. Reconnect the plug.

Can I use a dimmer with this lamp?

No, this lamp is not suitable for dimmers or electronic switches. It must be connected directly to the mains.

How to orient the reflector?

Make sure the lamp is turned off and cool. Rotate the reflector to the desired angle.

How to orient the lamp arm?

Turn off and let the lamp cool down. For model 14101902L, simply pivot the arm. For model 14102002L, hold the arm, remove the position lever, tilt the arm, then reinsert the lever.

What to do if the lamp does not turn on?

Check that the mains plug is properly inserted and that the socket works. Make sure the ON/OFF switch is in the on position. If the problem persists, contact customer service.

Are the LED modules replaceable?

No, the LED modules are not replaceable. When they reach the end of their life, the entire lamp must be replaced.

How to clean the floor lamp?

Unplug the lamp and let it cool down. Use a dry, lint-free cloth. Never use water, solvents or abrasive cleaners.

What is the warranty for this product?

The warranty is 36 months from the date of purchase. It covers material and manufacturing defects. Keep the receipt and the serial number (14101902L or 14102002L).

Where can I find customer service?

You can contact customer service by phone at +49 (0) 29 61 / 97 12-800 or by email at [e-mail]. The website is www.briloner.com. Have the IAN 285602 number ready.

USER MANUAL IAN 285602 Livarno Lux

Operation and Safety Notes

NL BE

STAANDELED-LAMP

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device.

FR BE

GB / IE Operation and Safety Notes Page 11

Technical diagram illustrating a mechanical device with numbered components and motion indicators, including a magnified inset of the component.

Intended use Page 12

Scope of delivery Page 12

Parts description Page 12

Technical Data Page 13

Safety Page 13

Safety information......Page 13

Preparation......Page 14

Required tools and material Page 14

Start-up Page 14

Mounting the light....Page 14

Adjusting the height Page 14

Switching the lamp on/off......Page 14

Adjusting the reflector....Page 14

Adjusting the lamp arm....Page 14

Maintenance and Cleaning......Page 15

Disposal Page 15

Warranty and Service......Page 15

Warranty Page 15

Manufacturer / Service Page 15

Declaration of conformity....Page 15

List of pictograms used
	Read the instructions!		Danger to life and risk of accidents for infants and children!
	Volt (AC) Warning! Danger of electric sh
	Hertz (frequency) For your safety
	Watt (effective power)		This lamp is not suitable for dimmer or electronic switches.
	Safety class II Warning - Hot surfaces!
	This lamp is only suitable for indoor use in dry and enclosed spaces.		Dispose of the packaging and device in an environmentally-friendly manner!
	Observe the warnings and safety notices!

LED Floor Lamp

Introduction

Congratulations on your new product.

You have selected a high quality product.

Please be sure to carefully read the com-

plete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. Should you have any questions or you are unsure about operating the product, please contact the dealer or service centre. Please keep these instructions in a safe place and pass them on third parties as applicable.

Intendeduse

This light is only suitable for indoor use in dry and enclosed spaces.

This product is intended for private household use only.

- Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 LED Floor lamp, model 14101902L or 14102002L
1 Base
1 Adjustment lever
1 Counterweight (model 14102002L)
1 Instructions for use

Partsdescription

1 ON/OFF switch
2 Reflector
3 Adjustment lever
4 Retaining sleeve
5 Stand tube
5a Upper stand tube section
5b Lower stand tube section

5c 6 7 8 9 10 11
Cone
Mains plug
Stand
Counterweight (model 14102002L)
Locking lever (model 14102002L)
Lamp arm
Transportation lock

●TechnicalData

Modelno.:14101902Lor

14102002L

Operating voltage: 230–240 V\~, 50 Hz

Illuminant: 2 LED modules, each

approx. 5 Watts (LED module not replaceable)

Power factor

Illuminant (PF): 0.54

Illuminant rated current: 39 mA

Protection class: II/

Safety

Safetyinformation

Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions!

Avoid the risk of fatal injury from electric shock

- Check the light for damage every time before you use it. Never use the light if it shows any signs of damage.

WARNING!

A damaged light means danger of death from electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician.

■ To prevent hazards, a damaged flexible outer

lead on this lamp must be replaced by the manufacturer, its service representative or an equally qualified professional!

Before use, verify the available mains voltage corresponds with the operating voltage of the lamp (see „Technical Data“).
- Ensure that the light does not come into contact with water or other liquids under any circumstances.
■ Always unplug from the mains before assembling, disassembling, cleaning, or if the lamp will not be used for extended periods.
■ Never open any of the components of the electrical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock.
The LED module in this light cannot be replaced; if the LED module has reached the end of its life, replace the entire light.

This light is not suitable for dimmer or electronic switches.

Prevent fire and injury hazards

RISK OF INJURY!

Check every illuminant for damage immediately upon unpacking. Do not install the light if the illuminants are defective. In this case contact the service centre for a replacement.

Do not look directly into the illuminant (lamp, LED, etc.). Do not look into the illuminant (lamp, LED, etc.) with an optical instrument (e.g. magnifier).
Do not leave the light or packaging material lying unattended. Plastic film or bags, plastic parts etc. can turn into dangerous toys for children.
Do not cover the lamp or the mains plug with objects. Excessive heat can result in a fire.
■ Never leave the lamp unattended whilst in use.

Safe working

Mount the light so that it is protected from moisture and dirt.
Carefully prepare for assembly and allow yourself adequate time. Organise all parts and any

necessary additional tools or materials before starting so they are easy to reach.

Always be attentive! Always pay attention to what you are doing and use common sense.
■ Never assemble the lamp if you are unfocused or feel unwell.
In order to disconnect the lamp completely from the power supply, the mains plug must be removed from the socket.

● Preparation

• Required tools and material

The tools and materials specified are not included. This information and these values are non-binding and are only provided as a reference. The nature of the material is determined by the individual local conditions.

- Screwdriver

- Start-up

- Mounting the light

Note: When assembling the stand tube 5 be sure not to damage the mains lead inside the lamp.

□ Unfold the floor lamp.
Remove the transport lock from the support tube 5.
☐ Insert the upper stand tube section 5a into the lower stand tube section 5b.
Carefully pull the mains lead out of the stand tube 5.
Be sure the cone is seated correctly.
Tighten the retaining sleeve to secure the stand tube 5.
Screw the lower stand tube section clockwise into the base 7.
☐ Screw the adjustment lever 3 onto the reflector 2. You will need a small screwdriver to do this.
Plug the mains plug into a properly installed socket.

Your light is now ready to use.

- Adjusting the height

□ Unplug the mains plug from the socket before adjusting the light.
☐ Loosen the retaining sleeve.
☐ Adjust the floor lamp to the desired height.
Tighten the retaining sleeve.
Note: Retighten the retaining sleeve 4 if it loosens and the lamp adjusts in height. Plug the mains plug into the socket.

- Switching the lamp on / off

☐ Switch the lamp on or off using the ON / OFF switch 1 on the reflector 2.

• Adjusting the reflector

Note: only change the position of the reflector 2 if the light is switched off.

Allow the light to cool off completely.
Turn the reflector to the desired angle.

- Adjusting the lamp arm

Note: only change the position of the lamp arm 10 if the light is switched off.

Allow the light to cool completely.

Model 14101902L: turn the lamp arm 10 to the desired position.

Model 14102002L: hold on to the lamp arm 10. Loosen the locking lever 9. Move the lamp arm 10 to the desired position. Tighten the locking lever 9.

Note: retighten the locking lever 9 if the lamp arm 10 moves out of position.

● Maintenance and Cleaning

WARNING! DANGER OF ELECTRIC SHOCK!

First unplug the mains plug 6 from the socket.

⚠️ CAUTION! RISK OF BURNS DUE TO HOT SURFACES!

Allow the lamp to cool down completely.

WARNING! DANGER OF ELECTRIC SHOCK!

For electrical safety, never clean the light with water or other liquids, or immerse it in water.

Do not use solvents, benzene or similar substances. They could damage the light.
☐ Only use a dry, lint-free cloth for cleaning.
Plug the mains plug into the socket.

- Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1–7: plastics / 20–22: paper and fibre-board / 80–98: composite materials.

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

- Warranty and Service

Warranty

You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has been carefully produced under strict quality control.

Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect arising during the warranty period, please send the appliance to the listed Service Centre address, making reference to the following article number: 14101902L/14102002L.

Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Manufacturer / Service

Please have your receipt and the article number (e.g. IAN 12345) ready as your proof of purchase when enquiring about your product.

Declaration of conformity

This product fulfils the requirements of the applicable European and national directives. Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.