IAN 311296 - Bike accessory CRIVIT - Free user manual and instructions

Product type	SP-84 bicycle helmet
Brand	Crivit
Model	IAN 311296
Category	Bicycle accessory
Dimensions	Sizes adjustable via occipital dial
Weight	Approx. 300 g (estimated)
Power supply	None (non-electric accessory)
Outer material	ABS shell (estimated)
Inner material	EPS foam and removable padding
Closure	Magnetic clip lock
Adjustment system	One-hand continuous adjustment dial
Chin guard	Removable, attached via Velcro
Intended use	Bicycle, skateboard, roller skates, scooter
Safety standards	Certified according to current standards
Lifespan	5 years after manufacture or after any impact
Care and cleaning	Warm water, mild soap, air drying
Spare parts and repairability	Not repairable; replace if damaged
Included accessories	Removable chin guard
Warranty	Statutory warranty of conformity

Frequently Asked Questions - IAN 311296 CRIVIT

How to properly adjust the helmet?

Place the helmet horizontally on your head. Use the dial at the back to adjust the size: turn right to tighten, left to loosen. The straps should form a V under your ears, and the chin strap should be adjusted to exert slight pressure when you open your mouth.

What type of cleaning is recommended?

Clean the helmet only with warm water, mild soap, and a soft cloth. Never use chemical products, paints, or stickers. Allow to air dry after each use.

When should the helmet be replaced?

Replace the helmet after any severe impact or deep scratch, even without visible damage, and no later than 5 years after its manufacture date. It should also be replaced if it no longer fits perfectly.

Does the helmet protect against all accidents?

No, even when properly adjusted, the helmet cannot protect against all injuries. It is designed to reduce the risk of head trauma but does not guarantee absolute protection.

Can I use this helmet for sports other than cycling?

This helmet is specifically designed for cycling, skateboarding, roller skating, and scooter riding. Do not use it for climbing, motorcycling, or any activity with a risk of strangulation.

How does the magnetic lock work?

To open the closure, push it to the side. To close it, bring the two halves together: internal magnets attract them and a mechanical lock secures them. Caution: keep magnets away from objects sensitive to magnetic fields.

How to install the chin guard?

Place the chin guard over the chin strap and close it with the Velcro strip. Make sure it is securely attached before each use.

Can the helmet be exposed to heat?

Avoid temperatures above 60 °C. Do not place the helmet behind a car window, near a fireplace, or heat source. Formation of small bubbles or an uneven surface indicates heat damage.

How to dispose of the helmet at end of life?

Contact your local waste management company for disposal. Do not throw it in household waste without prior information.

What to do if the straps or chin strap are incorrectly adjusted?

Adjust the strap clip so that it is under the ear, without covering the ear. For the chin strap, use the adjuster on the buckle: tighten if too loose, loosen if too short. Check the closure before each ride.

USER MANUAL IAN 311296 CRIVIT

Bicycle helmet SP-84

Casque de velo SP-84

DE AT CH

FAHRRADHELM SP-84

Gebrauchsanleitung

NL BE

FIETSHELM SP-84

Gebruiksaanwijzin

GB 1E

BICYCLE HELMET SP-84

owner's manual

PL

KASK ROWEROWY SP-84

Bicycle helmet SP-84 08

Safety information 08

User information 09

1. The correct helmet position 09
2. Adjusting the single-hand twisting fastener 09
3. Adjusting the strap divider 10
4. Adjusting the chin strap 10
5. Opening and closing the magnetic fastener 10
6. Chin pad 10
7. Cleaning and care 10
8. Disposal 11
9. Declaration of Conformity 11

BICYCLE HELMET SP-84

Dear Customer!

We are pleased that you have decided to purchase one of our high-quality products, which are manufactured and certified in strict adherence to the currently valid safety standards.

Familiarize yourself with this product before first use. Carefully read the operating instructions and the safety information. Use the product only as described and for the indicated purposes. Keep these instructions. If you give the product to a third party, be sure to include all the documents with it.

Safety information

• Warning! This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child gets trapped with the helmet.
• Your helmet was specially designed for protection during cycling, skateboarding, roller-skating and riding a scooter. It must not be used for other types of

sport or for motorcycling

• Please note that the helmet can only provide protection if it fits correctly. Pleas ensure you try out a range of different sizes before buying.
• Please be aware that despite correct adjustment your helmet cannot always protect you from all injuries.
• The helmet should be checked for visible deficiencies at regular intervals.
• The helmet must be replaced after every hard knock, impact or deep scratch, because these cause it to lose its protective effect. When the helmet no longer fits properly, it must be replaced.
• The helmet must also be replaced when it no longer fits properly or no later than 5 years after the date of manufacture, even if no damage can be detected.
• Any adjustment to or removal of the original parts of the helmet can extremely impair its protective function. The helmet may not be altered in order to make additions in a way not recommended by the manufacturer.
• Clean the inner padding with lukewarm water and mild soap and then let it air dry.
• High temperatures, from as low as 60^ C, can seriously damage the helmet. Uneven helmet surfaces and the formation of small blisters are signs of such damage. Do not store behind panes of glass, e.g. in the car or close to sources of heat or warmth.

User information

1. The correct helmet position

• The helmet must always be levelly horizontal on your head (Fig. A).
• If the helmet is too far forward, it can impair your vision.
• If the helmet is too far back, your forehead is not sufficiently protected (Fig. B).

2. Adjusting the single-hand twisting fastener

The integrated size-adjusting system can be adjusted using a turning knob at the back of one's head (Fig. C):

• smaller = twist clockwise
• bigger = twist anti-clockwise

3. Adjusting the strap divider

• Open the strap divider (Fig. D).
• The strap divider must be positioned in such a way, that the straps are taut but comfortable. The strap divider must be below the ear, and the straps must not cover the

ears.

• Close the strap divider (Fig. E).

An open strap divider can lead to slipping of the helmet in the event of an accident and thus to a loss of protection!!!

4. Adjusting the chin strap

• The chin strap (Fig. G.3) has been adjusted correctly if you feel slight pressure when you open your mouth. The buckle shall not be positioned on the jawbone.
• If the chin strap (Fig. G.3) is too loose it must be pulled tight using the winding (Fig. G.2) on the fastener (Fig. G.1).
• If the chin strap (Fig. G.3) is too tight it must be loosened also using the winding (Fig. G.2) on the fastener (Fig. G.1).

Please note that you must always make sure that the fastener is closed before you ride !!! (Fig. F)

Please be aware that the helmet can only protect if it fits properly. Please try out different sizes and choose the one in which the helmet fits comfortably and sits firmly upon your head.

5. Opening and closing the magnetic fastener

• The snap fastener is opened by pushing sideways. To close it, simply fit the two fastener halves into one another. They automatically snap together because of the internal magnets and are held firmly together by a mechanical closure that locks in place (Fig. F).

Attention: Keep magnets away from all devices and objects that can be damaged by magnetic fields.

6. Chin pad

• Place the chin pad on chinstrap and secure it with the hook-and-loop fastener (Fig. H).

7. Cleaning and care

• All chemicals, paints and stickers can seriously impair the protective effect of the helmet.
• Only clean your helmet with lukewarm water, mild soap and a soft cloth.
• After every use, leave your helmet exposed to the air in order for it to dry.

8. Disposal

Please contact your local waste disposal company for the disposal of the helmet.

9. Declaration of Conformity

The complete Declaration of Conformity can be found at www.speq.de.

Chere cliente, cher client!

Hotline [phone]

e-mail: [e-mail]

web: www.speq.de

TÜV Rheinland LGA Products GmbH

Tillystrasse 2

D-90431 Nurnberg

notified body no. 0197

Stand der Information · last update · Version des informations · Stand

van de informatie · Stav informaci · Version de la informacion