Beautiful VV5740 - Hair dryer Concept - Free user manual and instructions

USER MANUAL Beautiful VV5740 Concept

VV 574XACKNOWLEDGMENT Thank you for purchasing a Concept product. We hope you will be satised with our product throughout its service life. Please study the entire Operating Manual carefully before you start using the product. Keep the manual in a safe place for future reference. Make sure other people using the product are familiar with these instructions. Technical parameters Voltage 220–240 ~50/60 Hz Input 1400-1600 W Noise level < 84 dB(A)

IMPORTANT SAFETY INSTRUCTIONS

• Use the unit only as described in this operating manual.

• Remove all the packaging and marketing materials from the unit before the rst use.

• Make sure the mains voltage corresponds to the values on the rating plate.

• For further protection, it is recommended to install a current protector (RCD) with the actuating current not exceeding 30 mA in the power circuit of the bathroom. Please consult an electrician.

• The unit reaches high temperatures during operation and remains hot for some time after being turned o. Do not touch the hot surfaces. Use the handles and buttons. There is a risk of being burned.

• The unit may not be cleaned, stored, or covered until it has cooled down completely.

• Do not leave the unit unattended while it is turned on or even only plugged into the wall outlet.

• If you need to lay the unit aside during use, always switch it o and lay it on a reproof surface.

• Before plugging in or unplugging the unit from the wall outlet, make sure the switch is OFF.

• When disconnecting the unit from the wall outlet, never pull the

VV 574Xpower cord. Grasp the plug and disconnect it by pulling.

• Do not allow children or unskilled people to handle the unit. Use the unit out of the reach of these individuals.

• Persons with limited movement capacity, reduced sensory perception, insucient mental capacity or those who are unaware of the proper handling should use the product only under the supervision of a responsible, aware person.

• Take extra care when using the unit near children.

• Don’t let anyone use the unit as a toy.

• Turn the unit o, unplug the power cord from the wall outlet, and let the unit cool before cleaning and after use.

• Do not let the power cord hang loosely over the edge of a table. Make sure the power cord does not touch hot surfaces.

• Do not let the unit hang loosely on the power cord.

• Do not use the unit in an environment with explosive gases or ammable substances (solvents, varnishes, adhesives, etc.).

• Do not use hairspray or other spray products when the unit is in use.

• Keep the appliance clean; prevent foreign matter from entering the grille openings. It might damage the appliance, cause a short circuit, or a re.

• During use, do not cover the input or output grilles of the unit.

• Do not use abrasive or chemically aggressive substances to clean the appliance.

• Do not use the unit if it does not operate properly, or if it has been dropped, damaged or exposed to any liquids. Refer the unit to an authorised service centre for testing and repair.

• Never use the appliance if the supply cable or plug has been damaged; have the defect repaired immediately by anauthorised service centre.

• Do not wrap the power cord around the unit.

• The appliance is not designed for outdoor use.

VV 574X• Do not immerse the supply cable, the plug, or the appliance itself in water or any other liquid.

• Do not use any other accessories except those recommended by the manufacturer.

• Never repair the appliance yourself. Instead, contact an authorised service centre for repair.

• This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons if they are properly supervised or have been informed about how to use of the product in a safe manner and understand the potential dangers. Children must not play with the appliance. This appliance may be cleaned by children 8 years of age and older if they are properly supervised. Keep this appliance and the power cord out of reach of children younger than 8 years of age. Failure to follow the manufacturer‘s instructions may cause refusal of warranty repair. NOTE: Do not use the unit near bathtubs, basins or other vessels lled with water. When using the unit in a bathroom, make sure you switch it o immediately after use, and disconnect it from the wall outlet, as the proximity of water and any contact of the unit with water is very dangerous, even if the unit is switched o. Do not touch the unit with damp or wet hands, and do not handle it if your feet are wet, or you are barefoot.

The unit is designed to dry human hair. Do not use it on wigs or animals.

1. Dry your hair with a towel after washing.

2. Brush your hair. Do not use hairspray or other ammable substances.

3. Uncoil the supply cable. Connect the power cord plug to the wall outlet.

4. Select the desired air speed by the regulator (8).

level = unit is switched o.

level = very low air ow

level = very strong air ow

5. During drying, style your hair using a comb. Keep a safe distance in order to avoid burning the hair and

skin, or sucking your hair into the inlet grille.

6. The COOL function (ow of cold air) - is used for quick cooling of your hair, and subsequently gives better

hold to the hairstyle. To activate this function, press button (3).

7. When putting down the unit during use, always switch it o.

8. The removable nozzle enables aiming a narrow air stream towards the comb or brush you are using on

10. When using the unit in a bathroom, make sure you switch it o immediately after use, and disconnect it

from the wall outlet, as the proximity of water and any contact of the unit with water are very dangerous, even if the unit is switched o.

11. The hanging loop enables you to hang up the unit to store it.

CLEANING AND MAINTENANCE

WARNING! Always disconnect the power supply cable from the mains outlet before cleaning the appliance. Make sure the appliance has cooled down before handling it. Only use a wet cloth for cleaning the surface; never use detergents or hard objects, as they may damage it. Check the cleanliness of inlet and outlet grilles after each use. If necessary, press the button for releasing of the inlet grille (8), remove inlet grille, clean it and replace. Never clean the unit under running water, do not rinse it, and do not submerge it in water!

VV 574XTROUBLESHOOTING Problem Cause Solution The motor is not running. The plug is inserted into the socket incorrectly or insuciently. Check the plug connection. The socket is not live. Check to make sure voltage is present, e.g. by using another appliance. The supply cable is damaged. Refer the unit to an authorized service centre for testing and repair. A motor kikapcsol The air ow is incorrect or too low and, consequently, the motor overheating fuse has been activated. Disconnect the power supply cable from the socket. Check and clear the air passage on the inlet and outlet grilles. Let the unit cool. REPAIR & MAINTENANCE Any extensive maintenance or repair that requires access to the inner parts of the product must be performed by an expert service centre. ENVIRONMENTAL PROTECTION

• Packaging materials and obsolete appliances should be recycled.

• The transport box may be disposed of as sorted waste.

• Polyethylene bags shall be handed over for recycling. Appliance recycling at the end of its service life: A symbol on the product or its packaging indicates that this product should not go into household waste. It must be taken to the collection point of an electric and electronic equipment recycling facility. By making sure this product is disposed of properly, you will help prevent the negative eects on the environment and human health that would otherwise result from inappropriate disposal of this product. You can learn more about recycling this product from your local authorities, a household waste disposal service or in the shop where you bought this product. This product meets all the basic EU regulation requirements that relate to it. Changes to the text, design and technical specifi cations may occur without prior notice and we reserve the right to make these changes.

VV 574XEN WARRANTY TERMS Warranty The manufacturer (or importer) is responsible for en- suring the product complies with the requirements of applicable legal regulations as well as those of the rel- evant technical standards. Moreover, they are respon- sible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and fur- ther they are responsible for ensuring the product is t for the purpose proposed by the manufacturer or that a product of the same type is normally used for. The quality warranty term is 24 months from product takeover by the customer. The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer. The warranty specically does not apply:

• if the product installation, operation and service conditions stipulated in the product operating manual have not been adhered to,

• to malfunctions caused due to mechanical, heat or chemical damage, short circuit, over voltage or incorrect installation,

• to malfunctions caused by an inexpert third-party intervention,

• to malfunctions caused by natural disaster,

• to malfunctions caused by insucient or inappro- priate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,

• to changes in colour of the heating surface or to scratching of the surface caused as a result of us- ing the products in an unusual manner,

• to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,

• if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc. The warranty does not apply to any products and services provided along with the product (gifts, promotional articles, etc.). Filing a complaint A complaint against a product defect must be led as soon as identied, yet no later than before the end of the warranty term. The customer must le a product complaint with the dealer from which they have purchased the product, or with any authorised service centre, a list of which is included in the product package, or available at www.my-concept.com. While ling a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorised service centre, where relevant, unless the product is delivered in person. The customer must submit proof of having concluded a purchase contract for the product by producing the receipt. While ling their complaint, the customer must indicate the noted defect and identify the preferred complaint application method. Complaints processing As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis. Where such a procedure is not reasonable with regard to the nature of the defect, the user may require to be supplied a new defect-free product (replacement), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the defect can be removed without undue delay, the customer has the right to have the defect removed free of charge. 74 VV 574XEN WARRANTY TERMS Warranty The manufacturer (or importer) is responsible for en- suring the product complies with the requirements of applicable legal regulations as well as those of the rel- evant technical standards. Moreover, they are respon- sible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and fur- ther they are responsible for ensuring the product is t for the purpose proposed by the manufacturer or that a product of the same type is normally used for. The quality warranty term is 24 months from product takeover by the customer. The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer. The warranty specically does not apply:

• if the product installation, operation and service conditions stipulated in the product operating manual have not been adhered to,

• to malfunctions caused due to mechanical, heat or chemical damage, short circuit, over voltage or incorrect installation,

• to malfunctions caused by an inexpert third-party intervention,

• to malfunctions caused by natural disaster,

• to malfunctions caused by insucient or inappro- priate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,

• to changes in colour of the heating surface or to scratching of the surface caused as a result of us- ing the products in an unusual manner,

• to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,

• if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc. The warranty does not apply to any products and ser- vices provided along with the product (gifts, promo- tional articles, etc.). Filing a complaint A complaint against a product defect must be led as soon as identied, yet no later than before the end of the warranty term. The customer must le a product complaint with the dealer from which they have purchased the pro- duct, or with any authorised service centre, a list of which is included in the product package, or available at www.my-concept.com. While ling a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorised service centre, where relevant, unless the product is delivered in person. The customer must submit proof of having conclud- ed a purchase contract for the product by producing the receipt. While ling their complaint, the customer must indi- cate the noted defect and identify the preferred com- plaint application method. Complaints processing As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis. Where such a procedure is not reasonable with re- gard to the nature of the defect, the user may require to be supplied a new defect-free product (replace- ment), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the defect can be removed without undue delay, the customer has the right to have the defect removed free of charge. If the noted defect is not removable, or if the custom- er becomes entitled to replacement of the product or a part thereof, yet the replacement is not possible, for example due to the product having been sold out, the customer has the right to return the product (withdrawal from the contract). The customer shall have the right to a new product (re- placement) or to replacement of a part of the product even if the defect can be removed, provided they can- not properly use the product due to repeated occur- rence of the defect or due to a high number of such de- fects. In such a case, the customer also has the right to return the product (by withdrawing from the contract). If the product is not returned (the customer does not withdraw from the contract), or if the customer does not apply the right to a new defect-free product (replacement), to replacement of a part thereof or to repair of the product, they may request a reasonable discount. The customer also has a right to a reason- able discount if a new defect-free product cannot be supplied to them, or if a product part cannot be replaced or the product repaired unless the situation is remedied within a reasonable time limit, or if rem- edying the situation would create major discomfort on the part of the customer. The seller, authorised service centre or a sta member authorised by them must decide about each complaint immediately or within three business days in complicat- ed cases. This term does not include areasonable period of time, depending on the type of product concerned, required for the defect to be assessed by an expert. A complaint, including defect removal, must be dealt with without any undue delay, yet no later than within 30 calendar days of the complaint ling date, unless the seller and the customer agree on a later deadline. On returning the product (withdrawing from the contract) the customer must return any accessories and documents supplied along with the product. The customer does not have the right to keep the defective parts and components of the product replaced as part of a repair of the product. This shall be without prejudice to any other rights the customer may have in relation to the purchase of the product. Remark: Complaints against products damaged in transport are governed by the carrier’s complaints procedure. Manufacturer Jindřich Valenta - Concept Vysokomýtská 1800, 565 01 Choceň Czech Republic tel.: [phone] fax [phone] Company ID No. 13216660 email: [e-mail] www: www.my-concept.com Product data Model: Production number: Date of purchase: Seal and signature of vendor: