Z30888A - Uncategorized MELINERA - Free user manual and instructions

USER MANUAL Z30888A MELINERA

Cable tie Technical data Operating voltage: 230–240 V

, 50 Hz Protection class: II / IP class: IP44 (splash water protected) TÜV SÜD / GS certified. LED: 3 V , 0.06 W 24 LED per meter Rated power: HG04039A: 13.5 W HG04039B: 13.5 W HG04039C: 13.5 W LED are not replaceable.7 GB/IE/NI Safety Instructions BEFORE USING THE PRODUCT,

USE! WHEN PASSING THIS

TODDLERS AND CHILDREN! Never leave children unsupervised with the packaging material. The packaging material represents a danger of suffocation. Children frequently underestimate the dangers. Please keep children away from the product at all times. This product is not a toy and should not be played by children. Children are not able to under- stand the dangers that can occur when handling this product. This product can be used by chil-

ren aged from 8 years and abo

and persons with reduced physi- cal, sensory or mental capabilities or lack of experience and knowl- edge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Clean- ing and user maintenance shall not be made by children without supervision. Avoid the danger of death from electric shock! Before use, ensure that the mains voltage available is the same as the required operating voltage for the product (230–240 V

Before connecting to the mains, always check the product for any damage. Never use the product if you find damage of any kind. The connecting cable cannot be repaired! If the cable is damaged, the product must be taken out of use and disposed of in the proper way. This product does not contain any parts which can be serviced by the user. The bulbs cannot be replaced. The LEDs are not replaceable. If the LEDs fail at the end of their lives, the entire product must be replaced.8 GB/IE/NI Never open any of the electrical parts or insert any kind of object into them. Do not open or cut the product. Protect the product from sharp edges, mechanical loads and hot surfaces. Do not install with sharp fasteners or nails. Always remove the mains plug from the socket before installing, dismantling or cleaning. Never touch the mains plug or the product with wet hands.

CAUTION! RISK OF OVER-

HEATING! Do not cover the product with blankets, cushion or similar heat-insulating material. Do not operate the product whilst it is still in the packaging. Use the product only with the p arts described in these instructions. If the product is not to be used for any length of time (e.g. holidays), disconnect it from the power supply. Keep the product away from p onds and other bodies of water. Install the product at least 2 m from wat

containers. Avoid locations where flooding occurs after heavy rain. Use the product outdoors only when connected to a mains soc ket protected by a residual- current product (RCD) with a rated trip current of not more than 30 mA. Please note that the plug / power adapter continues to draw a small amount of power even if the product is turned off as long as the plug / power adapter is plugged into a power outlet. To switch the product off completely, unplug the plug / power adapter from the socket. Do not recessed into a surface. Outdoor mains sockets must be suitable for use outdoors and should be at least 2.5 m from the nearest water container or body of water. The product is protected against splash water (IP44). This protec- tion standard is only possible if the mains socket also fulfills re- quirements of at least the same protection class. Ensure that the product is not laid out through areas in which lawn mowers, strimmers, shears or similar cutting tools are used. Ensure that the product does not present a trip hazard. If you have any questions about the product or are unsure about any of its aspects, please seek the advice of an electrical equip- ment specialist.9 GB/IE/NI Before use Note: Remove all packaging materials from the product. Installation Place the 3D rope light figure

on a stable substrate. For outdoor installation, if possible fix the 3D rope light figure

in place with the ground spikes

Check the stability of the 3D rope light figure

For indoor installation, place the 3D rope light figure

on an even surface and fix it with the cable ties

into the socket. The product is switched on. To turn the lighting off, remove the mains plug

after the product is connected to the socket of power supply. The timer button

will light up when the timer function is activated. The product lights glow permanently for 6 hours and will be followed by a subsequent pause of 18 hours. Afterwards, the product will light up again at its designated turn on time for 6 hours followed by a subsequent pause of 18 hours. To switch off the timer function, press the timer button

again and the light of the timer but- ton

will be turned off. Cleaning and care CAUTION! RISK OF ELECTRIC SHOCK! First remove the mains plug

from the socket. CAUTION! RISK OF ELECTRIC SHOCK! For reasons of electrical safety the product must never be cleaned with water or other liquids or immersed in water. Let the product cool before you clean it. Risk of injury! Do not use any solvents, petrol or similar items. This would damage the product. Only a dry, lint-free cloth should be used for cleaning. Disposal The packaging is made entirely of recyclable mate- rials, which you may dispose of at local recycling facilities.

PRODUCT VERTROUWD MET

NEER U HET PRODUCT AAN