DAS180BAHWDB - Air Conditioning DANBY - Free user manual and instructions

USER MANUAL DAS180BAHWDB DANBY

INSTALL THIS APPLIANCE.***

• Use this appliance only for its intended use, as described in this manual.

• Never allow children to operate, play with, or crawl inside the appliance.

• Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion.

• Do not store or use flammable vapors or liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

• Do not use this product near water, e.g. in a wet basement, laundry room or near a sink.

• Do not cover or block any openings on the appliance.

• This appliance should be serviced only by a qualified HVAC technician. Contact the dealer at the location where the appliance was purchased for information on servicing the appliance.

• Disposal of this appliance should be in accordance with federal and local regulations.

• This appliance is not intended for use by persons (including children) whose physical, sensory or mental capabilities may be different or reduced, or who lack experience or knowledge, unless such persons receive supervision or training to operate the appliance by a person responsible for their safety.

• Do not climb onto or place objects on top of the outdoor appliance.

• Do not operate this appliance with wet hands as this can cause electric shock.

• Do not insert fingers or other objects into the air inlet or outlet as the fan rotates at very high speed and can cause serious injury or damage.

• Do not allow the appliance to operate for long periods of time with doors or windows open or if the humidity is very high. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. The serial rating plate indicates the voltage and frequency the appliance is designed for. WARNING - Improper use of the grounding plug can result in a risk of electric shock. Consult a qualified electrician or service technician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Important Safety Information

• SWING, TURBO or SLEEP features are turned on will display for 3 seconds when:

• SWING, TURBO or SLEEP features are turned off will display when anti-cold air feature is turned on will display when the appliance is defrosting

• In fan mode, the appliance will display the room temperature

• In other modes, the appliance will display the temperature setting

Optimal performance for the COOL, HEAT and DRY modes can be achieved in the following temperature ranges. When the air conditioner is used outside of these temperature ranges, certain safety protection features will activate and cause the appliance to perform less efficiently. COOL mode HEAT mode DRY mode Room temperature 17°C - 32°C (63°F - 90°F) 0°C - 30°C (32°F - 86°F) 10°C - 32°C (50°F - 90°F) Outdoor temperature 0°C - 50°C (32°F - 122°F) -15°C - 30°C (5°F - 86°F) 0°C - 50°C (32°F - 122°F)

OPERATION WITHOUT THE REMOTE CONTROL

Note: The manual button is intended for testing purposes and emergency operation only. Do not use this function unless absolutely necessary. To restore regular operation, use the remote control to activate the appliance. Operational functioning can be access through the remote control. In the event that the remote control fails to work, the appliance can be operated manually with the manual control button located on the indoor appliance. Note that manual operation is not an efficient long-term solution and that operating the appliance with the remote control is recommended. The appliance must be turned off before manual operation. To operate the appliance manually:

1. Open the front panel of the indoor appliance.

2. The manual control button is located on the right

side hand side of the appliance.

3. Press the manual control button one time to

activate forced AUTO mode.

4. Press the manual control button a second time to

activate forced COOL mode.

5. Press the manual control button a third time to turn

6. Ensure the front panel is closed when finished.

To optimize the performance of the appliance:

• Keep doors and windows closed

• Do not block air inlets or outlets

• Regularly inspect and clean all air filters

• Limit energy usage by using the timer function Note: When the outside temperature is below 0°C (32°F), keep the appliance plugged in at all times to ensure smooth ongoing performance. OPERATING INSTRUCTIONS

• The air conditioner will not operate if curtains, doors or other materials block the signal from the remote control to the indoor appliance.

• Do not expose the remote control to water, direct sunlight or excessive heat.

• Do not allow direct sunlight to fall on the infrared receiver on the indoor appliance as this can impede the signal from the remote control.

• Remote signal reception is confirmed with a beep. OPERATING INSTRUCTIONS ON/OFF: Turns the appliance on or off MODE: Selects mode operation in the following order: Auto --> Cool --> Dry --> Heat --> Fan FAN: Selects fan speed in the following order: Auto --> Low --> Med --> High SLEEP: Conserves energy during sleeping hours TURBO: Starts and stops the turbo function, which will run the appliance continuously to reach the preset temperature in the shortest amount of time; after running for 30 minutes turbo mode will stop Symbol will flash to indicate that the appliance has received the signal from the remote control. UP AND DOWN BUTTONS: Used to increase or decrease the temperature setting in 1° increments. Press and hold the up and down buttons for three seconds to change the temperature scale between °C and °F SHORTCUT: Used to restore the current settings or resume previous settings TIMER ON: Used to set automatic on function TIMER OFF: Used to set automatic off function DIRECT: Used to change the louver movement and set the up or down air flow direction SWING: Used to start or stop the horizontal louver swing feature LED: Turns the LED display on or off Remote Control Specifications Model RG57B/BGEU1 Rated Voltage 3.0V (dry batteries R03/LR03x2) Signal Receiving Range 8m (26 feet) Environment -5°C to 60°C (23°F to 140°F)OPERATING MODES AUTO mode

• Press the MODE button to select AUTO mode.

• The appliance will automatically select cooling, or fan only operation depending on what temperature has been set and the ambient room temperature. DRY (dehumidifying) mode

• Press the MODE button to select the DRY mode.

• The fan speed cannot be adjusted in this mode. The fan operates at LOW speed.

• Keep windows and doors closed for the best dehumidifying effect.

• Condensed water will automatically drain through the drain hose. Note: The fan speed cannot be adjusted in AUTO and DRY mode. COOL mode / HEAT mode / FAN operation

• Press the MODE button to select the desired mode; COOL, HEAT or FAN.

• Press the UP or DOWN buttons to select your desired room temperature. The temperature can be set within a range of 17°C - 30°C (62°F - 86°F).

• Press the FAN button to choose the fan speed: Auto, Low, Med or High. SHORTCUT function (only available on remote):

• Used to save a favourite setting

• Set the unit to the temperature and fan speed that you would like to set as a favourite

• Press and hold the SHORTCUT button for 2 seconds

• Press the SHORTCUT button at any point in future to return to the favourite setting

• If no favourite is set, pressing the SHORTCUT button will cause the unit to run in AUTO mode at 26°C (79°F), with fan speed set to AUTO Anti-Cold Air Feature

• The fan speed and the louver angle adjust according to the ambient temperature. The manual control button and remote control cannot adjust fan speed or louver angle in this setting. SLEEP function

• The SLEEP function is used to decrease energy use during sleeping hours. This function can only be activated by pressing the SLEEP button on the remote control.

• When in COOL mode, the temperature will increase by 1°C (2°F) in the first hour and will increase an additional 1°C (2°F) in the second hour. The appliance will then hold this new temperature for 5 hours. At the end of the SLEEP cycle, the appliance will resume normal operation.

• When in HEAT mode, the temperature will decrease by 1°C (2°F) in the first hour and will decrease an additional 1°C (2°F) in the second hour. The appliance will then hold this new temperature for 5 hours. At the end of the SLEEP cycle, the appliance will resume normal operation. Note: The sleep feature is not available in FAN and DRY mode. AUTOMATIC FEATURES Auto-Restart If the appliance loses power, it will automatically restart with the previous settings once power is restored. Louver Angle Memory When turning on the appliance, the louver will automatically resume the previous angle setting. Refrigerant Leakage Detection The indoor appliance will automatically display “EC” when it detects a refrigerant leakage and the appliance will shut off. OPERATING INSTRUCTIONS

• Ensure the appliance is turned on

• Press the TIMER OFF button and the Timer Off indicator will illuminate

• Press the TIMER OFF button to select the desired amount of hours before the appliance turns off To set the Auto-on timer:

• Ensure the appliance is turned on

• Press the TIMER ON button and the Timer On indicator will illuminate

• Press the TIMER ON button to select the desired amount of hours before the appliance turns on Notes:

• The TIMER ON and TIMER OFF buttons will increase the time in 0.5 hour increments up to 10 hours and then in 1 hour increments up to 24 hours

• The display will revert back to showing the previous temperature setting if the appliance does not receive a signal within a 5 second period during programming

• Turning the appliance on or off at any time or adjusting the timer setting to 0.0 hours will cancel the TIMER settings Using the TIMER ON and TIMER OFF feature at the same time The appliance can be set to turn on and run for a set period of time and then turn off again by using the TIMER ON and TIMER OFF features at the same time. Keep in mind that the hours displayed on the appliance refer to the number of hours that will pass from the current time before the action is taken. For example:

• First, set the Auto-off timer

• Ensure the appliance is turned on

• Press the TIMER OFF button and the Timer Off indicator light will illuminate

• Press the TIMER OFF button to select the desired amount of hours before the appliance turns off

• Press the TIMER ON button within 5 seconds and the Timer On indicator light will illuminate

• Press the TIMER ON button to select the amount of hours before the appliance turns back on Note: If the TIMER OFF function and the SLEEP function are used at the same time, the appliance will only implement the setting whose duration is shorter. If the TIMER OFF function is set for less than seven hours, the TIMER OFF will turn the appliance off before the SLEEP function can complete its cycle. If the TIMER OFF function is set for more than seven hours, the SLEEP function will turn the appliance off before the TIMER OFF can complete its cycle. OPERATING INSTRUCTIONSSETTING VERTICAL ANGLE OF AIR FLOW While the appliance is on, use the SWING/DIRECT button to set the vertical angle of the air flow.

1. Press the SWING/DIRECT button once to

activate the louver. Each press of the button will adjust the louver by 6°.

2. To make the louver swing up and down

continuously, press and hold the SWING/ DIRECT button for 3 seconds. Press it again to stop the continuous swing.

SETTING HORIZONTAL ANGLE OF AIR

FLOW The horizontal angle of the air flow must be set manually. Grip the deflector rod and manually adjust it to the preferred direction.

NOTE ON LOUVER ANGLES

When using COOL or DRY mode, do not set the louver at an extreme vertical angle for a long period of time. Water can condense on the louver blade which can then drip on the floor or furnishings. When using COOL or HEAT mode, do not set the louver at an extreme vertical angle for a long period of time. This can cause reduced performance due to restricted air flow. Do not force the louver to move or adjust the louver by hand. This will cause the louver to be out of sync and it will not function correctly. If this occurs, turn off the appliance and unplug it for a few seconds and then restart the appliance. This will reset the louver position. CAUTION Do not put fingers in or near the blower and suction side of the appliance. The high-speed fan inside the appliance can cause serious harm or injury. OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4. Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment. This appliance complies with Part 15 of the FCC Rules and Industry Canada’s license-exempt RSS. Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation. This device complies with Canadian CAN ICES-3 (B) / NMB-3 (B)

REPLACING THE REMOTE BATTERIES

The appliance comes with two AAA batteries. Place the batteries in the remote control before use.

1. Slide the back cover from the remote downward to expose the battery

2. Insert the batteries, ensure to match the (+) and (-) symbols on the ends of

the batteries with the symbols inside the battery compartment.

3. Slide the battery cover back into place.

• Do not mix old and new batteries or batteries of different types.

• Do not leave the batteries in the remote control if it is not going to be used for more than 2 months.

• Do not dispose of batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. Note: Removing the batteries from the remote will erase all previous programming. After inserting new batteries, the settings on the appliance must be reprogrammed.CLEANING THE INDOOR APPLIANCE Note: Always turn off the air conditioner and disconnect the power source before cleaning the appliance or removing the filter.

• Use a soft, dry cloth to clean the outside of the appliance. If the appliance is especially dirty, use a cloth soaked in warm water to clean the outside of the appliance.

• Do not use water to clean the inside of the appliance as this can destroy the insulation and cause electric shock.

• Do not use chemicals or chemically treated cloths to clean the appliance.

• Do not use benzene, paint thinner or other solvents to clean the appliance. They can cause the plastic surface to crack or deform.

• Do not use water hotter than 40°C (104°F) to clean the front panel. This can cause the panel to deform or become discoloured.

CLEANING THE AIR FILTER

A clogged air filter can reduce the efficiency of the air conditioner. It is advisable to clean the air filter every two weeks or after 240 hours of operation, whichever comes first. When removing the filter, do not touch any metal parts inside the appliance as the sharp metal edges can cause injury.

1. Lift the front panel of the indoor appliance.

2. Grip the tab on the end of the filter, lift it up and

pull it outwards to remove it from the appliance.

3. If the filter has a small air freshening filter, unclip if

from the larger filter. Clean the air freshening filter with a soft brush or hand-held vacuum cleaner.

4. Clean the large filter with warm, soapy water.

5. Rinse the filter with clean water. Ensure all soap

is removed from the filter and shake off excess water.

6. Dry the filter in a cool, dry place. Do not expose

the filter to direct sunlight as this can warp or shrink the filter.

7. When the filter is dry, replace the air freshening

filter and then slide the larger filter back into the appliance.

8. Close the front panel of the indoor appliance.

Note: Do not touch the air freshening (plasma) filter for at least 10 minutes after turning off the appliance to allow it to cool. CARE & MAINTENANCE

If the air conditioner will not be used for a long period of time, complete the following:

1. Turn on the FAN function until the appliance is

2. Turn off the appliance and disconnect the power.

3. Clean and replace all filters.

4. Remove the batteries from the remote control.

MAINTENANCE - PRE-SEASON INSPECTION After a long period of non-use or before a period of frequent use, complete the following:

1. Check for damaged wires.

2. Clean all filters.

4. Replace the remote control batteries.

5. Ensure nothing is blocking air inlets and outlets.

Ensure nothing is in the way of the infrared remote receiver.

MAINTENANCE AND CLEANING OF THE

OUTDOOR APPLIANCE Any cleaning, maintenance or repairs of the outdoor appliance must be completed by a licensed HVAC technician. Contact the dealer who sold the appliance for information on maintenance or repairs to the outdoor appliance. DISPOSAL Check for local regulatory compliance regarding the approved and safe disposal of this appliance. ERROR CODES If an error code appears in the display window, the appliance may stop operation as a safety feature. Wait approximately 10 minutes as the error may resolve itself. If the error code persists, disconnect the power to the appliance, wait approximately 5 minutes and then restore power to the appliance. If the error persists after the power cycle, contact the sales center where the appliance was purchased for information on servicing the appliance. CARE & MAINTENANCEDanby consumer care: 1-800-263-2629 Hours of operation: Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time Friday 8:30 am - 4:00 pm Eastern Standard Time Information in this manual is subject to change without notice. TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE

The appliance does not start when pressing on/off button

• The appliance has a protection feature that prevents it from being turned back on for 3 minutes after being turned off to avoid overloading

• Room temperature is lower than the set temperature. (Cooling mode)

• Room temperature is higher than the set temperature (Heat mode)

• A fuse is burned out

• Remote control batteries have burned out The appliance changes from COOL or HEAT to FAN mode automatically

• The appliance may change mode to prevent frost from forming on the internal coils

• The set temperature has been reached, at which point the compressor is turned off. The appliance will continue operating when the room temperature fluctuates from the set temperature The indoor or outdoor appliance are emitting white mist

• In humid regions, a large temperature difference between the room temperature and the set temperature can cause white mist

• When the appliance restarts in HEAT mode after defrosting, white mist may be emitted due to moisture generated from the defrosting process The indoor or outdoor appliance are making noise

• A rushing air sound may occur when the louver resets its position

• A squeaking sound may occur after running the appliance in HEAT mode due to the expansion and contraction of internal plastic parts

• A low hissing sound during operation is normal; this is caused by refrigerant gas flowing through the appliance Dust is emitted from the appliance

• The appliance may accumulate dust on the internal components during long periods of non-use, which will be emitted when the appliance is turned on The appliance emits a bad odor

• The appliance may absorb odors from the surrounding environment, (cooking smells, animal smells, cigarette smells, etc.) which will be emitted during operation

• The filter has become clogged and should be cleaned The fan of the outdoor appliance does not operate

• During operation, the fan speed on the outdoor appliance is controlled to optimize product efficiency Operation is erratic, unpredictable, or appliance is unresponsive

• Interference from cell phone towers and remote boosters may cause the appliance to malfunction. To reset the appliance: disconnect the power then reconnect and press the power button to restart operation Poor cooling or heating performance

• Temperature setting is higher or lower than the ambient room temperature

• The outdoor temperature is extremely high or low

• The air filter is clogged

• The air inlet or outlet is blocked

• Doors and windows are open

• Low refrigerant due to leak or long-term use

• The heat exchanger is dirty The appliance starts and stops frequently

• There is too much or too little refrigerant in the system

• Incompressible gas or moisture has entered the system

• The voltage is too high or too low

• The compressor is malfunctioning

11LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer. This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided. First Year During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser. To obtain Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance Service requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice”below. Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service must be performed by a qualied service technician. If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all obligations of Danby under this warranty shall be void. Boundaries of If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be In Home Service delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he responsibility of the purchaser. Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper. EXCLUSIONS Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit. GENERAL PROVISIONS No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.Danby Products LimitedPO Box 1778, Guelph, Ontario, Canada N1H 6Z9Telephone: (519) 837-0920 FAX: (519) 837-0449Danby Products Inc.PO Box 669, Findlay, Ohio, U.S.A. 45840Telephone: (419) 425-8627 FAX: (419) 425-862904/09 1-800-263-2629 Warranty ServiceIn-home Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided During the first five (5) years, from the date of purchase by the original purchaser, any functional parts of this product found to be defective, will be provided by the manufacturer at warrantor’s option, at no charge to the ORIGINAL purchaser.First 5 years

5 YEAR LIMITED APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer.This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.TERMS OF WARRANTYThis product is warranted for residential or light commercial use.EXCLUSIONSSave as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representa-tions or guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by the unit.GENERAL PROVISIONS This Warranty does not cover the following:

1) Labor or other costs incurred for diagnosing, repairing, removing, installing, servicing or handling of either

defective parts, replacement parts or new units.2) Power Failure.3) Damage in transit or when moving the appliance.4) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

5) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal

operating conditions (extremely high or low room or exterior temperature).

6) Failure, damage or repairs due to faulty installation, misapplication, abuse, improper servicing, unauthorized

alteration or improper operation.7) Fire, water damage, theft, war, riot, hostility, acts of God.8) Parts required for normal maintenance.

9) Damage or repairs to property due to faulty installation, misapplication, abuse, improper servicing, unauthorized

alteration or improper operation. Including but not limited to improper installation on drainage hose.

10) In the event a replacement part is necessary they will be warranted for the remaining period of the original

warranty period.11) Transportation after installation.

12) Environmental or temperature conditions that would affect performance of the unit as a whole or parts as per

manufacture guidelines. Proof of purchase date will be required for warranty claims; please retain bills of sale. Danby Products Limited PO Box 1778, Guelph, Ontario, Canada N1H 6Z9 Telephone: (519) 837-0920 FAX: (519) 837-0449 Danby Products Inc. PO Box 669, Findlay, Ohio, U.S.A. 45840 Telephone: (419) 425-8627 FAX: (419) 425-8629 1-800-263-2629

10/23EXIGENCES DE SÉCURITÉ

PROBLÈME CAUSE POSSIBLE

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer. This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.TERMS OF WARRANTY Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided. First Year During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser. To obtain Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance Service requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice”below. Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service must be performed by a qualied service technician. If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all obligations of Danby under this warranty shall be void. Boundaries of If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be In Home Service delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he responsibility of the purchaser. Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.EXCLUSIONS Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit. GENERAL PROVISIONS No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

PROBLEMA CAUSA POSSIBLE

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer. This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.TERMS OF WARRANTY Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided. First Year During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser. To obtain Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance Service requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice”below. Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service must be performed by a qualied service technician. If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all obligations of Danby under this warranty shall be void. Boundaries of If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be In Home Service delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he responsibility of the purchaser. Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.EXCLUSIONS Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit. GENERAL PROVISIONS No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.