EK 6022 CB - Fireplace BOMANN - Free user manual and instructions

Product Type	Electric Fireplace
Brand	Bomann
Model	EK 6022 CB
Net Weight	16,2 kg
Power Supply	220-240 V~, 50 Hz
Heating Power	1000 W / 2000 W (selectable)
Auxiliary power consumption in standby	0,48 W
Protection Class	I
Installation Type	Permanent wall mounting
Minimum safety distance	1 meter from flammable objects
Minimum installation height	30 cm from the floor
Minimum room volume	4 m³
Display	LED screen with date, time, temperature
Flame effect	LED, adjustable intensity (via remote control)
Ambient lighting	7 colors, adjustable
Control type	Touch panel + infrared remote control (range 10 m)
Programmable functions	Up to 10 programs, weekly clock
Overheat protection	Yes, automatic shutdown
Cleaning	Soft dry cloth; glass with damp cloth
LED repairability	Not replaceable by user
Recommended use	Well-insulated rooms or occasional use

Frequently Asked Questions - EK 6022 CB BOMANN

How to install the Bomann EK 6022 CB electric fireplace?

Installation requires permanent wall mounting. Use the mounting bracket (745 mm) and the supplied support. Drill 8 mm holes, fix with dowels and screws. Hang the device, then secure the support. The device must be at least 30 cm from the floor, 1 m from flammable objects, and never under a wall socket.

What is the maximum heating power and how to adjust it?

The maximum power is 2000 W. You can select 1000 W, 2000 W or disable heating via the POWER button on the panel or the 1000W/2000W button on the remote control. The indicator shows the active power.

How to set the date and time?

Press DATE/TIME on the remote control. The arrow and day blink: adjust with ▲/▼, confirm with DATE/TIME. Then set the hours, then the minutes. Finish with OK.

What to do if the remote control stops working?

Check the batteries (2x AAA, 1.5 V). Replace them observing polarity. Make sure there is no obstacle between the remote control and the sensor (top left corner of the device). The range is about 10 m.

How to program automatic on and off?

First set the date and time. Press TIMER SET, choose a program number (1-10), select the day(s), the on time (ON) and off time (OFF), then the temperature. Activate the programming with TIMER ON/OFF. The ∅ symbol appears.

How to clean the electric fireplace?

Unplug the device and let it cool. Clean the surfaces with a soft dry cloth. For the front glass, use a damp cloth, then dry. Never use abrasive products or metal brushes.

Why does the heating not turn on even though the device is on?

The room temperature may be higher than the set temperature. Increase the base temperature (15-30°C) with the + or - buttons on the remote control. The heating only activates if the room temperature drops below the set point.

What to do in case of overheating and alarm?

The device emits an alarm signal and the screen flashes. Set the power switch to O, unplug, and let it cool for 15 min. Check that the air inlets/outlets are not obstructed. If the problem persists, contact customer service.

Can I use an extension cord?

Yes, but the cable cross-section must be at least 1.5 mm². Do not use multiple sockets because the device is powerful. Avoid plugging other powerful appliances into the same circuit.

How to turn off the device completely?

For temporary shutdown, press ON/OFF (remote control) or I/O (panel). To completely cut off power, set the power switch to O and unplug the plug.

USER MANUAL EK 6022 CB BOMANN

Flame on a dark, glossy surface with warm orange and yellow tones (no text or symbols visible)

Simple diagram showing a rectangular frame with a blank center and two small circles, labeled 'C' at the bottom (no text or symbols within the frame)

Diagram showing two device panels with arrows indicating movement or transformation, no text or symbols present

Bedienungsanleitung

Thank you for choosing our product. We hope you will enjoy using the appliance.

Symbols in these Instruction Manual

Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the appliance:

WARNING:

This warns you of dangers to your health and indicates possible injury risks.

CAUTION:

This refers to possible hazards to the appliance or other objects.

NOTE: This highlights tips and information.

Contents

Overview of the Components....3

Assembly 4

General Notes......16

Special Safety Instructions for this Appliance....17

Handling Batteries 19

Unpacking the Appliance....19

Scope of Delivery....19

Overview of the Components....19

Control Panel on the Appliance....19

Remote Control....19

Display....20

Assembly Instructions....20

Electrical Connection....20

Power Requirements....20

Connection 20

Remote Control....20

Inserting the Batteries (Batteries not included)....20

Remote Control Range 20

Operation 21

Switching on the Appliance 21

Basic Setting of the Appliance 21

Close Operation of the Appliance 21

Operate of the Appliance from the Distance....21

Setting the Current Day of the Week and the Time.....21

The Timer....22

Display Timer Settings ....22

Programming the Timer 22

Activating/Deactivating the Timer 22

End of Operation....23

Overheating Protection....23

Cleaning 23

Maintenance Instructions 23

Troubleshooting....23

Technical Data....24

Disposal 24

Meaning of the "Dustbin" Symbol....24

Product Data Sheet......25

General Notes

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this appliance to other people, please also pass on the operating instructions.

- The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use.

- Do not use it outdoors. Keep it away from sources of heat, direct sunlight, humidity (never dip it into any liquid) and sharp edges. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately.

- When cleaning or putting it away, switch off the appliance and always pull out the plug from the socket (pull the plug itself, not the lead) if the appliance is not being used and remove the attached accessories.

- Do not operate the appliance without supervision. If you leave the room you should always turn the appliance off. Remove the plug from the socket.

- The appliance and the mains lead have to be checked regularly for signs of damage. If damage is found the appliance must not be used.

- Use only original spare parts.

- In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

WARNING:

Do not allow small children to play with the foil.

There is a danger of suffocation!

Special Safety Instructions for this Appliance

You will find the following symbol with warning character on the appliance:

WARNING: Do not Cover!

To prevent overheating of the heating appliance, the heating appliance may not be covered.

WARNING:

Risk of Electrical Shock!

Do not install this heating appliance in close proximity to a bathtub, a shower, or a swimming pool.

Risk of Explosion

The inside of the appliance contains glowing hot components. Do not use the appliance around flammable or explosive liquids or gases!

Risk of Burning

• Some parts of the product can become very hot and cause burns. Avoid contact with the skin.
• You must be particularly careful when children and vulnerable persons are present.
• The escaping air at the top of the appliance reaches temperatures of more than 100 °C! Do not allow children to play unattended in proximity to the appliance.

CAUTION:

Safety Distance

• The heating appliance must not be installed directly below a wall outlet.
• Maintain a 1 m safety distance to readily flammable objects such as furniture, curtains, etc.

CAUTION:

- Mount the appliance in a way that the air can flow freely in and out.

Use

This is an auxiliary heating appliance. Do not leave the appliance unattended for several hours. Do not leave the house while it is in use.

Risk of Overheating

Do not heat any rooms with a volume of less than 4 m^3 .

• Make sure that the power cable is not lying on the appliance.
• Do not insert any objects into the appliance.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Children younger than 3 years of age should be kept away from the appliance, unless they are supervised at all times.
• Children from the age of 3 and younger than 8 years of age may only turn the appliance on and off if they are supervised, or have been instructed with regard to the safe use of the appliance, and if they have understood the risks resulting from it, provided that the appliance has been placed and installed in its normal position of use.
• Children from the age of 3 and younger than 8 years of age may not insert the plug into the socket, may not adjust the appliance,

may not clean the appliance and / or may not perform the maintenance by the user.

- Do not repair the appliance by yourself. Always contact an authorized technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Handling Batteries

Insert correctly!

Do not charge!

Do not disassemble!

Danger of explosion! Do not expose batteries to intense heat, such as sunlight, fire or similar.

Do not short circuit!

Batteries should not be disposed in the domestic waste! Dispose empty batteries at a special collection point.

CAUTION:

• Different battery types or new and used batteries must not be used together.
• When not using the remote control for a long period of time, remove the batteries in order to prevent "leakage" of battery acid.

Unpacking the Appliance

CAUTION:

Do not hold the appliance using the glass front. It is only hanging loose at on the appliance.

1. Remove the appliance from its packaging.
2. Remove all packaging material such as plastic films, filler material, cable ties and cardboard packaging.
3. Check the content for any missing parts.
4. In the event that the packaging content should be incomplete or if damages are noticeable, do not operate the appliance. Return it to the dealer immediately.

NOTE:

The glass front is protected by a foil. We recommend not to remove this foil until after the appliance has been installed.

Scope of Delivery

1 Electric fireplace with glass front
1 Remote control
Installation material:

1 Mounting strip, 745 mm long
1 Mounting bracket, 50 mm long
7 Dowels, 8 mm long
7 Screws, 4 × 40 mm
2 Threaded screws, 10 mm

Overview of the Components

Control Panel on the Appliance

1 Button BACKLIGHT (lighting)
2 Button POWER
(heating power of 1000 W or 2000 W)
3 On/Off button I/O
4 Power switch
5 Control lamp for On / Off button
6 Control lamps for heating power

Remote Control

7 Button OK
8 On/Off button ON/OFF
9 Button ▲ or ▼
10 Button DATE/TIME
11 Button—
12 Button IC
13 Button 1000W/2000W
14 Button BACK-LIGHT
15 Button DIMMER
16 Button TIMER ON/OFF
17 Button C
18 Button+
19 Button TIMER SET

Display

20 Selection position (▶)
21 Weekday
22 Timer active (
23 Standby (
24 Temperature in °C or timer setting number
25 Timer turn-off time (OFF)
26 Timer start time (ON)
27 Time (98:88
28 Automatic, adaptive start control function of the heater (AUTO)
29 Intensity of the flames (↓)
30 Heating power of 1000 W (or 2000 W ()

Assembly Instructions

This appliance is intended for permanent attachment to a wall. It should be placed at least 30 cm above the ground. Please refer to the figures on page 4.

Do not switch on the appliance until it has been properly installed!

WARNING:

Make sure beforehand whether there are cables inside the wall which could be damaged!

CAUTION:

• The wall should be a load bearing and heat resistant wall.
• Do not hold the appliance using the glass front.
• The subsequent work requires manual skills. If necessary, get help from a specialist

NOTE:

• There must be a power outlet nearby, but not above the appliance. The hot air flow is emitted by the fan at the top of the appliance.
• Route the power cord right behind the appliance.
• In order to have an optimal view at the fireplace, we recommend installing it onto a height of 60 cm (see Fig. A).
• Use a size 8 drill bit to drill holes into the wall.

• You will also need a medium sized Phillips screwdriver.

• Gently place the appliance on the floor leaning against a wall.

• Use both hands to pull out the glass front evenly upwards. Set the glass front aside.
• Measure the height at which you want to mount the appliance. The recommended dimensions can be found in Fig. B.

• Use 5 screws and dowels to attach the mounting strip horizontally to the wall.

• Attach the mounting bracket with the threaded screws to the appliance.

• Hang the appliance into the mounting strip on the wall.
• Mark the positions of the 2 boreholes for the mounting bracket.
• Remove the appliance from the wall once again.
• Drill the 2 holes for the mounting bracket. Insert the dowels.
• Hang the appliance into the mounting strip on the wall.
• Use 2 screws to attach the mounting bracket to the wall.
• Hang the glass front back into the appliance. To do this, see Fig. D.

Electrical Connection

Power Requirements

The appliance can consume a total of 2000 W. With this connected load a separate supply line protected by a 16 A household circuit breaker is recommended.

CAUTION: Overload!

• If you use extension leads, these should have a cable cross-section of at least 1.5 ~mm^2 .
• Do not use any multiple sockets, as this appliance is too powerful.
• Do not connect any other powerful appliances to the same electric circuit.

Connection

• Make sure that the iron voltage and the line voltage match. The nameplate is located at the bottom of the appliance.
• The mains plug should only be inserted into a correctly installed socket with earthing contact.

Remote Control

Inserting the Batteries (Batteries not included)

1. Open the battery compartment cover on the back of the remote control.
2. Insert 2 batteries of type "AAA" • 1.5V • MICRO, observing the correct polarity (see markings on the bottom of the compartment)!
3. Close the battery compartment cover.

Remote Control Range

• The remote control has a range of approx. 10 meters. If the range decreases you should change the batteries.
• Make sure there are no obstacles between the remote control and the sensor of the appliance. It is located in the upper left area of the glass front.

Operation

CAUTION:

Do not switch on the appliance until it has been properly installed!

NOTE:

• The operation can partly be done via the control panel of the appliance.
  • To set the timer programming, use the remote control.
  • Each operating step will be acknowledged by a signal tone.
• When pressing a wrong button, you will hear two short beeps.
• After switching on the appliance, the display behind the glass front becomes visible. For a better ambience, the display will switch off approx. 20 seconds after each operation. Press any button to reveal the display again.

Switching on the Appliance

Set the power switch to position I. The appliance is in Standby. The ⏻ symbol lights up in the display.

Basic Setting of the Appliance

After switching on the appliance via the power switch, it will be in the following basic setting:

-Weekday = SUN (Sunday)
-Display of the current room temperature
-Time = 00:00
- Intensity of the flames 🐘... = high
-Lighting BACKLIGHT = off
-Base temperature for heating = 20°C
-Heating = off
-Timer = off

NOTE:

• Even in the event of a power failure, the appliance is reset to this basic setting.
• For safety reasons, the appliance will always start without heating.

Close Operation of the Appliance

• You can switch on the appliance on the control panel by briefly pressing the I/O button. The basic setting of the appliance will become visible in the display.
• If you want to change the intensity of the flames, press the I/O button for more than 3 seconds.
• You may turn on the lighting by pressing the BACKLIGHT button. Pressing this button repeatedly, will change the colours. There are 7 different colour variants.
• Press the POWER button once to activate the heating power for 1000 W. Press the POWER button a second time to activate the heating power for 2000 W. Pressing the button a third time will switch off the heating.

The control lamps beside the button are displaying the respective status.

NOTE:

The heater and the fan will not be switched on by the appliance until the room temperature is lower than the base temperature for the heater (see basic setting). You can increase the base temperature for the heating via the remote control.

Operate of the Appliance from the Distance

1. Switch the appliance on by pressing the ON/OFF button on the remote control. The basic setting of the appliance will become visible in the display.
2. Press the +or button to set the base temperature for the heater. Possible temperature range: Between 15 °C and 30 °C. Note that the base temperature must be higher than the current room temperature. If the room temperature falls below the set base temperature, the heating will switch on automatically.
3. Use the button 1000W/2000W to select the heating power:

Button	Appearance in the display	Heating power
Press 1 ×	☀️	1000 W
Press 2 ×	☀️ ☀️	2000 W
Press 3 × off

1. If you want to use the heater's adaptive start control function, press the IC button. "AUTO" will appear on the display. Based on the room temperature and the set temperature the appliance will automatically adjust the heating power.

2. Press the BACK-LIGHT button to select one of 7 colour variants.

3. Press the DIMMER button if you want to change the intensity of the flames.

Setting the Current Day of the Week and the Time

1. Press the DATE/TIME button. The arrow ▶ and a weekday will be flashing. Use the ▲ or ▼ button to select a weekday. Press the DATE/TIME button again to confirm the weekday.
2. The hour display starts flashing. Use the + or -button to set the current hour. Press the DATE/TIME button again to confirm the hour.
3. The minute display starts flashing. Use the + or - button to set the current minute.
4. Press the OK button to exit the menu.

The Timer

The appliance including heating can be time-controlled via the timer. Prerequisite for the correct operation of the timer is the setting of the current time and day of the week.

• You can set a maximum of 23 hours and 50 minutes in advance.
• The time setting is done in 10-minute increments.
• You may program up to 10 different timer settings.
  • Each timer setting includes its own switch-on time, switch-off time and temperature setting.
• A setting can be programmed for any day of the week or for several days.
• If you want, you may only program a switch-off time during operation and ignore the entry of the switch-on time. If the switch-off time is meant to be the next day, remember to adjust the day of the week when programming.
• Even if the appliance is disconnected from the mains, the timer settings will be preserved.

Display Timer Settings

1. Press the TIMER SET button. The number for the first setting flashes in the display and "ON" lights up.
2. Press the + or -button to display the switch-on times of the 10 timer settings.
3. Press the ▲ button in order to switch to the switch-off time. "OFF" will appear on the display.
4. Use the +or button to display the switch-off times.
5. To clear a displayed setting, press the C button.

Programming the Timer

i NOTE:

If you have accidentally made a wrong selection during timer programming, exit the menu by pressing the OK button and start again.

1. Select setting number

1) Press the TIMER SET button. The display of the timer setting number starts flashing.
2) Use the + or -button to select another setting number.
3) Press the TIMER SET button again to confirm the selection.

1. Weekday(s) selection

1) The arrow ▶ and a weekday will be flashing. Use the ▲ or ▼ button to select a weekday.
2) Press the button to activate the weekday. The arrow beside the weekday is flashing.
3) Press the TIMER SET button to confirm the selection.
4) If you want to deactivate a weekday, press the — button, while the arrow ▶ beside the weekday is flashing.

1. Setting the start time

("ON" will light up in the display)

1) The hour display starts flashing.
Use the + or -button to set the hour.
2) Press the TIMER SET button to confirm the selection.
3) The minute display starts flashing. Use the +or button to set the minute.
4) Press the TIMER SET button to confirm the selection.

1. Setting the switch-off time

("OFF" will light up in the display)

1) The hour display starts flashing. Use the + or -button to set the hour.
2) Press the TIMER SET button to confirm the selection.
3) The minute display starts flashing. Use the +or button to set the minute.
4) Press the TIMER SET button to confirm the selection.

1. Setting the base temperature for the heating

i NOTE:

For technical reasons, the current weekday is displayed again in this menu item.

1) The temperature display starts flashing. Use the + or - button to set the base temperature for the heater.
2) Press the TIMER SET button to confirm the selection.

Activating/Deactivating the Timer

i IMPORTANT NOTE:

• In the event of a power failure, all timer settings will be preserved. However, the appliance will be reset to the basic settings.
• For safety reasons, the heating will be switched off.

WARNING: Fire hazard!

• Before switching on the timer, check the settings of the current weekday, the current time and the timer settings.
  • Always set the start time in such a way that the appliance is under proper supervision during operation.

• Use the 1000 W/2000 W button to set the desired heating power. Alternatively, you may also use the IC button to select the adaptive start control function of the heater.

• Use the DIMMER button to set the intensity of the flames you wish to have at the start time.
• If you want the lighting to additionally switch on at the start time, select it now with the BACK-LIGHT button.
• By using the TIMER ON/OFF button you switch the timer on or off.

i NOTE:

• If the timer is activated, the Ⓞ symbol will appear in the display.
• In addition, the display will show the symbols for the intensity of the flames and for the heating, provided this it has been switched on.

End of Operation

• Did you activate the timer, or do you only want to temporarily switch the appliance to standby?
• To do this, use the ON/OFF button on the remote control or the I/O button (3) on the appliance.
• Do you want to disconnect the appliance from the mains?
• Set the power switch (4) to position O. Disconnect the power supply from the socket.

i NOTE:

The appliance will not turn on after disconnecting it from the mains, even if you have activated the timer. The appliance will be reset to the basic settings.

Overheating Protection

The appliance is fitted with an overheating protection, which will automatically turn off the appliance in case of overheating. You will hear a warning signal. All segments in the display start flashing. For safety reasons, the appliance will not turn itself on again.

In order for the appliance to be operated again, proceed as follows:

• Set the power switch to position O. Disconnect the power supply from the socket. Let the appliance cool down for approximately 15 minutes before you use it again.
• Check whether the air intake or vent on the heater is blocked. If necessary, clear the blockage.

In the event that the overheating protection turns off the appliance after a brief period, then there is probably a defect.

- Turn the appliance off again and unplug it from the mains.

- Have the appliance checked by the dealer or by our service.

Cleaning

WARNING:

• Before cleaning, always remove the mains plug and wait until the appliance has cooled down.
• Make sure no water enters the openings of the appliance during cleaning. Otherwise this might result in an electric shock or fire.

CAUTION:

• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
• Clean the surface of the appliance with a soft dry cloth.
• The glass front may be wiped wet, if necessary. Then dry it with a soft cloth.

Maintenance Instructions

- The appliance is equipped with an electronically controlled LED system that projects the flame effect. This system must not be serviced by the user.

• The LEDs of the lighting can not be replaced.

Troubleshooting

Problem Possible Cause Solution
The appliance does not work. The appliance is not connected to mains power.		Check the wall outlet with a different appliance.
		Insert the plug properly in the wall outlet.
		Check the fuse.
		The appliance is defective. Contact our service or a repair centre.
The heater and the fan are not working.	The room temperature is higher than the base temperature for the heating.	Check the setting for the base temperature.
The appliance is not turning on at the programmed start time.	The appliance has been disconnected from the mains (possibly due to power failure).The appliance has been reset to the basic settings	Check the settings of the current weekday, the current time and the timer settings.
The flame effect does not work.	A component is defective. Contact our service or a repair centre.
You will hear a warning signal. All segments in the display start flashing.	The overheating protection has been activated.	1. Switch off the appliance by using the power switch.2. Let the appliance cool down for at least 15 minutes before switching it on again.

Technical Data

Model:....EK 6022 CB

Power supply: 220 - 240 V\~, 50 Hz

Power consumption: 1000/2000 W

Protection class:....I

Net weight: .... approx. 16.2 kg

The right to make technical and design modifications in the course of continuous product development remains reserved.

This appliance has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Disposal

Meaning of the "Dustbin" Symbol

Protect our environment: do not dispose of electrical equipment in the domestic waste.

Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.

This helps avoid the potential effects of incorrect disposal on the environment and human health.

This will contribute to the recycling and other forms of re-utilisation of electrical and electronic equipment.

Information concerning where the equipment can be disposed of can be obtained from your local authority.

Product Data Sheet

Model identifier(s): EK 6022 CB
Item Symbol Value Unit Item Unit
Heat output Type of heat input, for electric storage local space heaters only
Nominal heat output P	nom	2.0 kW	manual heat	charge control, with integrated thermostat		N/A
Minimum heat output (indicative)	Pmin	1.0 kW	manual heat	charge control with room and / or outdoor temperature feedback		N/A
Maximum continuous heat output	Pmax,c	2.0 kW	electronic heat	charge control with room and / or outdoor temperature feedback		N/A
Auxiliary electricity consumption				fan assisted heat output		N/A
At nominal heat output (fan motor)	elmax	0.014 kW	Type of heat output / room temperature control
At minimum heat output (fan motor)	elmin	0.014 kW	single stage	heat output and no room temperature control		no
In standby mode el	SB	0.48	W	Two or more manual stages, no room temperature control		no
				with mechanic thermostat room temperature control		no
				with electronic room temperature control		no
				electronic room temperature control plus day timer		no
				electronic room temperature control plus week timer		yes
				Other control options
				room temperature control, with presence detection		no
				room temperature control, with open window detection		no
				with distance control option		no
				with adaptive start control		yes
				with working time limitation		no
				with black bulb sensor		no
Contact details	C. Bomann GmbH, Heinrich-Horten-Str. 17, 47906 Kempen / Germany

Mode d'emploi

SUN = domingo, MON = lunes, TUE = martes, WED = miércoles, THU = jueves, FRI = viernes, SAT = sábado

CTC Clatronic Sp. z o.o

Ul. Brzeska 1

45-960 Opole

Usuwanie