WaffelExpress Eis - Waffle Maker BEEM - Free user manual and instructions

Brand	BEEM
Model	WaffelExpress Eis
Product type	Waffle iron for ice cream cones
Type number	B 33.001
Dimensions (W x D x H)	255 x 205 x 115 mm
Weight	Approx. 1.56 kg
Operating voltage	220 – 240 V~
Mains frequency	50 Hz
Power	1200 W
Protection class	I
Coating of cooking surfaces	Anti-stick ceramic Bio-Lon® (without PTFE or PFOA)
Temperature setting	Yes, rotary dial (MIN to MAX)
Indicator lights	Red (heating) and green (cooking)
Included accessories	Cone for forming ice cream cones, instruction manual
Batter capacity per cone	1 to 2 tablespoons
Number of cones approx.	10 (with suggested recipe)
Safety instructions	Do not immerse, use only on a stable and heat-resistant surface, keep out of reach of children
Maintenance	Clean with a damp cloth, do not use abrasive products
Available spare parts	Cone for forming (ref. 900 880 001)
Additional manufacturer warranty	Visit www.beem.de
Intended use	Cooking ice cream cones (household use)

Frequently Asked Questions - WaffelExpress Eis BEEM

How to use the BEEM WaffelExpress Eis waffle iron for the first time?

Before first use, wipe the device with a damp cloth, close the lid, set the thermostat to MIN, plug it in, then turn to MAX for a few minutes to heat empty. Unplug, let it cool, then clean again. The first cone should not be consumed.

How to clean the waffle iron after use?

Always unplug the device and let it cool. Use a damp cloth to wipe the exterior and the cooking surfaces. Never immerse the appliance in water and do not use abrasive products that could damage the non-stick coating.

What is the correct temperature for cooking ice cream cones?

First set the thermostat to a medium position. The red light indicates heating; when it goes off and the green light comes on briefly, the temperature is reached. You can adjust during cooking according to the desired browning level.

How to shape the ice cream cones after cooking?

Place the cone provided in the center of the hot waffle. Bring one half of the waffle over the cone using a finger or spatula. Turn the cone to roll the waffle. Hold until cool to solidify the cone.

What batter recipe is recommended for this waffle iron?

The manual suggests: 50 g melted butter, 100 g powdered sugar, 180 ml milk, 130 g flour, and 1 packet vanilla sugar. Mix gradually, let rest 30 minutes, then cook 1 to 2 minutes per cone.

What to do if the appliance does not heat up?

Check that the plug is properly inserted and that the circuit breaker fuse is on. Ensure there are not too many appliances on the same circuit. If the problem persists, contact customer service.

Is the non-stick coating safe?

Yes, the Bio-Lon® coating is ceramic, without PTFE or PFOA. It is non-stick, resistant to high temperatures, and environmentally friendly.

Can I use metal utensils on the plates?

No, never use sharp objects or metal utensils to remove the cones, as they may damage the non-stick coating. Use a wooden or silicone spatula.

How to store the appliance when not in use?

Clean the appliance as instructed. Store it in a dry, clean place away from frost and direct sunlight. Keep out of reach of children.

Where to find spare parts for the waffle iron?

The available spare part is the cone for forming (ref. 900 880 001). Visit www.beem.de for accessories and spare parts.

USER MANUAL WaffelExpress Eis BEEM

Open the fold-out pages at the beginning and end of the user manual in order to view the illustration during reading.

General information. 15

Safety 17

Getting started 19

Appliance description 21

Operation and controls 21

Recipe suggestion. 23

Cleaning and care. 23

Storage 23

Simple troubleshooting. 24

Spare parts and accessories 24

Technical data. 24

Dear customer,

Before using the appliance, please read the information contained in this user manual regarding setup, safety and intended use as well as cleaning and care.

Open the fold-out pages at the beginning and end of the user manual so that you can view the illustrations while reading.

Keep this user manual for later use and give it to any future owner along with the appliance.

General information

Copyright

This document is copyrighted. Any copying or reprinting, in whole or in part, as well as distribution of the illustrations, even in altered form, is only allowed with the written consent of the manufacturer.

Environmental protection information

The packaging materials used can be cycled. Dispose of packaging mate which are no longer needed in accordance with local regulations.

This product may not be disposed of in normal household waste within the European Union. Dispose of the appliance via municipal collection points.

Warranty/guarantee

In addition to the statutory warranty obligation, BEEM also offers an extended manufacturer's guarantee on certain products.

If offered, you will find the appropriate details either on the product-specific packaging, promotional materials or on the BEEM website for the particular product.

The full warranty conditions, accessories available and spare parts as well as user manuals in various languages can be found on our website at www.beem.de.

Symbols used

DANGER

This is used for a hazard which is an immediate threat leading to severe bodily injury or to death.

To avoid the hazard, follow the instructions given here.

WARNING

This is used for a possibly hazardous situation which could lead to severe bodily injury or to death.

To avoid the hazard, follow the instructions given here.

CAUTION

This is used for a possibly hazardous situation which could lead to minor injuries.

To avoid the hazard, follow the instructions given here.

ATTENTION

This is used for a situation which could lead to material damage.

To avoid the hazard, follow the instructions given here.

Limitation of liability

We assume no liability for damage or consequential damage caused by:

• failing to observe the operating instructions,
• use for any other than the designated purpose,
  improper or inappropriate handling,
  inexpert repairs,
  unauthorised modifications,
• use of third-party parts and spare parts,
• use of unsuitable add-ons or accessories.

Conformity declaration

The BEEM company hereby declares that this appliance complies with the fundamental requirements and with the remaining applicable provisions of the directives 2006/95/EC, 2004/108/EC and 2009/125/EC. A complete declaration of conformity can be found under www.beem.de.

Safety

Safety regulations

Only use the appliance for the use described. Do not use the appliance for other, possibly similar, uses under any circumstances.
This appliance is not intended to be used by persons (including children) with limited physical, sensory or mental capabilities or insufficient experience and/or insufficient knowledge, except if they are supervised by a person responsible for their safety or have received instruction from this person as to how the appliance is to be used.
Supervise children to ensure that they do not play with the appliance. Store the appliance and the accessory parts out of the reach of children.
Inspect the appliance before use for visible, external damage. Do not operate a damaged appliance.
Do not leave the appliance unattended during operation.
Only use accessory parts of the manufacturer or those which are expressly recommended by the manufacturer. Otherwise all warranty or guarantee rights are void.
Do not use this appliance in combination with an external timer or a separate remote control system.
Only have repairs to the appliance performed by a customer service representative authorised by the manufacturer because otherwise, in the event of damage or subsequent malfunctions, there is no longer any guarantee or warranty coverage. This also applies specifically to the replacement of a damaged power supply cord. Considerable hazards for the user can result from improper repairs.

Only replace defective components with original spare parts. Only these parts ensure that the safety requirements are fulfilled.

Designated use

This appliance is primarily intended for non-commercial use indoors for making ice cream waffle cones.

Any other use, or a use which goes beyond these, constitutes improper use.

All claims whatsoever for damage arising from improper use are excluded.

The owner bears the sole risk.

Overview of hazards

Hazard due to electrical current

Do not use the appliance if the mains cord or plug are damaged.
Do not open the housing of the appliance under any circumstances. If energised connections are touched or the electrical or mechanical configuration is changed, there is a risk of electrical shock.
Never immerse the appliance or the mains plug in water or other liquids.
Unplug the mains plug from the socket in the following situations:

• When cleaning the appliance
• When the appliance is not in use
• When there is a malfunction of the appliance during operation

Always pull the power supply cord out of the mains socket by the plug and not by the mains cord itself.
Never carry, lift or move the appliance by the mains cord.

Risk of suffocation due to packaging material

Ensure that no children play with the packaging material.

Risk of burns due to hot surfaces

Only grasp the appliance by the handle.

Risk of scalding due to escaping water vapour.

• Avoid contact with the water vapour which can escape from the appliance.

Safe operation site

The operation site must meet the following requirements to ensure safe and trouble-free operation of the appliance:

The operating surface of the appliance must be solid, dry, level and both water and heat resistant.
The immediate surroundings of the appliance must not be hot, wet or very damp.
The socket must be easily accessible so that the mains connection can be disconnected quickly.
Furniture surfaces may possibly contain substances which could affect the feet of the appliance, causing them to soften. Place another material under the feet of the appliance if needed.

Getting started

Unpacking

Proceed as follows:

1. Take the appliance, all accessories and the user manual out of the box.
2. Remove all packaging material and protective films from the appliance and the accessories before using them for the first time. Do not remove the type plate or any warning notices. If possible, keep the original packaging for the duration of the appliance's warranty period so that the appliance can be packaged properly in the event of a warranty claim. Shipping damage voids the guarantee or warranty.

Checking the scope of supply

Proceed as follows:

1. Check the contents for completeness and visible damage. Do not operate a damaged appliance.
2. Notify your supplier promptly in case of an incomplete or damaged delivery.

Power connection

The following regulations for the electrical supply must be observed to ensure safe and trouble-free operation of the appliance:

1. Be certain that the appliance can be connected to a properly installed protective conductor electrical system. Operation using a socket without an earth conductor is not permitted. If in doubt, have the house mains network inspected by an electrician. The manufacturer assumes no responsibility for damage resulting from the absence or interruption of a protective earth conductor.
2. Before connecting the appliance, compare the electrical data (voltage and frequency) on the type plate with that of your electrical mains network. These data must match to avoid damage to the appliance. If in doubt, ask your electrical appliance retailer.
3. Be certain that the socket is protected by at least a 10 A automatic circuit breaker.
4. Be certain that the power supply cord is not damaged. Route the power supply cord in such a way that it poses no risk of stumbling. The power supply cord may not be routed over sharp edges and may not be pulled taut or kinked. The power supply cord must not come into contact with hot surfaces.

Before first use

WARNING

Risk of burns due to hot surfaces

Only grasp the appliance by the handle.

WARNING

Risk of scalding due to escaping water vapour

• Avoid contact with the water vapour which can escape from the appliance.

ATTENTION

Risk of damage to the non-stick coating of the baking surfaces.

Do not use any pointed objects or steel utensils to remove the ice cream waffle cones from the appliance.

Before the first waffle cones are baked, the appliance must be allowed to heat up for a few minutes while empty to remove residues due to manufacturing processes from the baking surfaces. Also for this reason, the first waffle cones produced in the new appliance should not be consumed due to hygienic considerations.

Proceed as follows:

1. Wipe off the appliance with a damp cloth.
2. Close the cover.
3. Set the temperature control (2) to the lowest level (MIN).
4. Put the mains plug into the socket.
5. Set the temperature control to the highest level (MAX). The red indicator lamp (4) shows that heating is occurring.

6. Wait a few minutes and then set the temperature control back to the lowest level (MIN).

7. Unplug the mains plug from the socket.

8. Open the cover.
9. Allow the appliance to cool down.
10. Clean the appliance and the accessories as described in the chapter Cleaning and care (page 23).

During initial usage of a new appliance, there may be an odour due to the materials used. The odour will subside after a short time.

Appliance description

(For illustrations, see the fold out page at the left.)

1 Handle
2 Temperature control
3 Indicator lamp (green), baking phase
4 Indicator lamp (red) heating phase
5 Forming cone for shaping waffle cones
6 Baking surfaces
7 User manual (not shown)

Bio-Lon® ceramic

The baking surfaces have a white ceramic non-stick coating. It is free of PTFE and PFOA and prevents the batter from sticking. Furthermore, it is scratch resistant, easy to clean, resistant to high-temperatures and environmentally friendly.

Operation and controls

WARNING

Risk of burns due to hot surfaces

Only grasp the appliance by the handle.

WARNING

Risk of scalding due to escaping water vapour
- Avoid contact with the water vapour which can escape from the appliance.

ATTENTION

Risk of damage to the non-stick coating of the baking surfaces.

Do not use any pointed objects or steel utensils to remove the ice cream waffle cones from the appliance.

Baking ice cream waffle cones

Proceed as follows:

1. Close the cover.
2. Put the mains plug into the socket.
3. First set the temperature control (2) to a medium setting to find the desired level of browning. If needed, you may also change the temperature setting while baking.
4. When the red indicator lamp (4) goes out and the green indicator lamp (3) lights up after a short while, the set baking temperature has been reached. Open the cover and place 1 - 2 tablespoons of batter carefully in the centre of the lower baking surface (6). About 2cm of the outer baking surface towards the edge should remain uncovered.
5. Lightly press the cover onto the lower baking surface while closing. After a while, the green indicator lamp will go out and the red indicator lamp will light. The appliance is now in baking mode.
6. After 1 - 2 minutes, briefly open the cover to see if the waffle cone has reached the desired degree of browning. If it is still too light, close the cover again and continue baking until the waffle cone is golden brown.
7. When the waffle is done and while it is still hot, wrap it around the forming cone (5) as described in the chapter, Forming waffle cones (page 22).
8. Now place the batter for the next ice cream waffle cone into the appliance and repeat the baking process until you have made the desired number of waffle cones.
9. Unplug the mains plug from the socket once all the ice cream waffle cones have been baked.

Note: When beginning the baking process, it may take a little longer for the waffle cones to get done. Once the appliance has been in use for a while, the baking time will become shorter.

Forming waffle cones (figures A1-A4)

Proceed as follows:

1. Lay the forming cone (5) onto the centre of the hot waffle.
2. Using your finger (or a narrow spatula), push one half of the waffle cone over the forming cone. Hold the waffle firmly while doing so, as it may otherwise slide off the forming cone.
3. Now rotate the forming cone to complete shaping of the waffle cone.
4. Leave the forming cone in the shaped waffle until the waffle has cooled (only then will it be properly firm). In the meantime, you may already bake the next waffle.

You can also create waffle cups by shaping the waffles over a cup while they are still hot. Or you can create waffle rolls by rolling up the waffles on a level surface while they are still hot.

Recipe suggestion

Use the following ingredients for about 10 waffle cones:

• 50 ~g melted butter
  100 g powdered sugar
  180 ml milk
  130 g flour
  1 pkg. vanilla sugar

Proceed as follows:

1. Gradually stir the powdered sugar into the melted butter.
2. Then stir in the milk. Add the vanilla sugar and the flour and stir until the batter is smooth.
3. Allow the batter to rest for 30 minutes.

Cleaning and care

DANGER

Hazard due to electrical current!

Never immerse the appliance or the mains plug in water or other liquids.
Never hold the appliance under running water.

WARNING

Risk of burns due to hot surfaces
- Allow the appliance to cool down before cleaning.

ATTENTION

Risk of damage to the non-stick coating of the baking surfaces.
Do not use scouring agents for cleaning to avoid damage to the appliance.

Proceed as follows:

1. Unplug the mains plug from the socket.
2. Wipe off the appliance with a damp cloth.
3. Clean the baking surfaces (6) with a damp cloth.
4. The forming cone (5) may be cleaned in warm dishwater.

Storage

If you do not need the appliance for a longer period of time, clean it as described in the chapter Cleaning and care (page 23).

Store the appliance and all accessories in a clean, dry and frost-free location protected from direct sunlight.

Simple troubleshooting

The following table is intended to help in identifying and remedying small problems:

Problem Possible cause Remedy
The appliance does not work.	Plug not plugged in.	Plug it in.
	Automatic circuit breaker in the electrical system switched off.	Switch on the circuit breaker.
The automatic circuit breaker in the electrical system triggers.	Too many appliances connected to the same power circuit.	Reduce the number of appliances in the power circuit.
	No problem can be identified.	Contact customer service.

If you are unable to remedy the problem using the above steps, please contact the customer service department.

Spare parts and accessories

Item* Part no. Designation
5	900 880 001	Forming cone for shaping waffle cones

*Number according to the appliance description.

Technical data

Model	Ice Cream Waffle Cone Maker Eiswaffel-Express
Type number B 33.001
Dimensions (L x W x H)	255 x 205 x 115 mm
Weight, approx. 1.56 kg
Operating voltage	220 - 240 V~
Mains frequency 50 Hz
Power	1200 W
Protection class	I

Table des matieres

Informations generales 25

Sécurité 27

Mise en service 29

no observancia del manual de instrucciones,
-这么做 may be beneficial to the public, but it is not necessary to do so.
tratumiento inadecido o inapropiado,
reparaciones realizadas inadequadamente,
-merican no autorizadas,
-这么做 is not a good idea. It takes too much time and energy to make a new, complex, and complex program.
-这么做 is not a good idea. It can be expensive, and it takes time.
- you should use the same pieces of material in different ways to make the same product.
- you should use the same tools for making the same product.

Customer service points:

Bureau der service Apre-s-ventes:

Elements of Lifestyle

BEEM GmbH

Subject to printing errors.

For service in other countries contact your local dealer.