TKG SIS 11 - Iron KALORIK - Free user manual and instructions

USER MANUAL TKG SIS 11 KALORIK

Steam Ironing Station

Centrale Vapeur

Stoomgenerator

Central de planchado

Labeled diagram of a portable air conditioner with numbered parts for identification

D

1. Power switch
2. Pump pilot light
3. Detachable water tank
4. Grip of the water tank
5. Temperature dial
6. Steam button
7. Water tank cap
8. Pilot light of the iron
9. Connection cord
10. Iron support
11. Power cord
12. Steam control knob

F

Please read these instructions carefully before using the appliance.

Important: People (including children) who are not able to use the appliance in a safe way, due to their physical, sensorial or mental capacity or their lack of experience or knowledge, must never use the appliance except if they are supervised by a person responsible for their safety or if they previously received instructions concerning the safe use of the appliance.

Close supervision is necessary to prevent children from using the appliance as a toy.

☐ Check that your main voltage corresponds to that stated on the appliance.
☐ Never leave the appliance unsupervised when in use.
□ Always place the base of the appliance on a stable ironing board, table or on the ground.
☐ Only connect the appliance to a main earthed wall socket.
☐ To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
☐ The iron shall be used and placed on a stable level surface.
☐ When you place the iron on its support, make sure that the surface on which you put it is stable.
☐ Do not use the iron if it has fallen, if it shows any visible signs of damage or if it leaks.
☐ If an extension cord is absolutely necessary, a 10-ampere or higher cord should be used. Never use cords rated for less than 10-ampere. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.
☐ Never leave the appliance unsupervised when switched on and especially the steam iron when it is heating. Keep out of reach of children or incompetent persons.
From time to time check the cord for damages. Never use the appliance if cord or appliance shows any signs of damage. In that case, repairs should be made by a competent qualified electrician ^() . Should the cord be damaged, it must be replaced by a competent qualified service ^() .
☐ Only use the appliance for domestic purposes and in the way indicated in these instructions.
☐ Never immerse the iron or the base in water or any other liquid for any reason whatsoever.
□ Never use the appliance near hot surfaces.
☐ Do not allow power cord and cord binding the base to the steam iron to touch hot surfaces.
☐ Never use the appliance outside and always place it in a dry environment.
☐ Never use accessories that are not recommended by the producer. They could constitute a danger to the user and risk to damage the appliance.
☐ Never move the appliance by pulling the cord. Make sure the cord cannot get caught in any way. Do not wind the cord around the appliance and do not bend it.
☐ Fully unwind the main cord and supply hose before starting to iron.
□ Always unplug the appliance when it is not in use.
☐ Burns can occur from touching hot metal parts, hot water, or steam.
□ Always place the iron on the base of the appliance, on the therefore foreseen place. Do not place iron by its rear cover. Be sure that it does not come in contact with flammable materials or with the main cord.
☐ Never fill the steam tank with vinegar, descaling agents or other chemicals.
Before the first use, remove any sticker or protective foil from the soleplate. Clean the soleplate with a soft cloth.
☐ Some parts of the iron have been slightly greased and as a result the iron might slightly smoke when switched on for the first time. After a short while, however, this will cease.
☐ The iron shall be used and placed on a stable level surface.

☐ Do not use the iron if it has fallen, if it shows any visible signs of damage or if it leaks.
☐ When you place the iron on its support (if available with the model), make sure that the surface on which you put it is stable.
☐ Proceed the same way if the water tank stops working or is damaged. To avoid the risk of electric shock, do not disassemble the iron or steam tank, take it to a qualified technician for examination and repair. Incorrect re-assembly can cause a risk of electric shock when the iron or steam tank is used.
☐ Fully unwind the main cord and supply hose before starting to iron.
☐ The power switch should always be put in position "0" before plugging or unplugging the power cord from outlet.
☐ Unplug the appliance and allow the iron and the water tank to cool down before cleaning or storing them and for pressurized steam iron station (depending on the model) before opening, filling or emptying the water tank.
☐ FOR PRESSURIZED STEAM IRONING STATION (DEPENDING ON THE MODEL), NEVER OPEN THE CAP OF THE STEAM TANK WHILE THE APPLIANCE IS CONNECTED TO THE MAINS WALL SOCKET AND ESPECIALLY WHEN STEAM IS BEING PRODUCED.

(1) Competent qualified service: after sales department of the producer or importer or any person who is qualified, approved and competent to perform this kind of repairs in order to avoid all danger. In any case you should return the appliance to this service.

BEFORE THE FIRST USE

• We recommend cleaning the iron before the first use as follows: fill the water tank, put the temperature dial on position "LINEN" and the steam regulator on MAX and let the iron heat for 10 minutes. When the temperature has been reached, take the iron from the base, hold it vertically and keep the steam button pressed for 30 seconds, then wait 30 seconds and repeat this cycle twice.
• Switch off the appliance (switch in position "0"), unplug it and let it cool down sufficiently, then clean the soleplate with a damp cloth.

STEAM IRON: PRECAUTION FOR USE AND TEMPERATURES

• Always check first if a label with ironing instructions is attached to the article that needs to be ironed. Follow these ironing instructions in all cases.
• If ironing instructions are missing but you know the kind of fabric, then see the table for recommended ironing temperatures.

Kind of textile	Temperature dial	Steam ironing
NylonSynthetic (e.g. acetate, acrylic, viscose, polyamide, polyester, ...)Silk	(ZASK)[77CS]	NO
Wool	(Z3Y4)	YES
CottonLinen	(Y008)	YES

• Plug in the appliance and put the switch (1) in position "I" to switch it on. The power light of the switch (1) and the pump pilot light (2) will light up, indicating that the appliance is working and the iron is heating. Set the temperature dial of the iron (5) to the desired position, the indicator lamp of the iron (8) will light up. As soon as the desired temperature is reached, the pilot light of the iron will go out and you can start ironing.
• During ironing this pilot light (8) will come on from time to time. When this happens, the soleplate is being heated up to the required temperature again. You can continue ironing.
• The table is valid for the fibre materials only. If some kind of finish has been applied (gloss, wrinkle, relief etc), the textile can best be ironed at a lower temperature. First sort out the fabrics according to ironing temperature: wool with wool, cotton with cotton, etc.
• The iron heats up quicker than it cools down. Therefore, start ironing the articles requiring the lowest temperature such as those made of synthetic fibres. Then progress to the higher temperatures.
• If the article is made of a mixture of different fibres, you must always select the lowest ironing temperature of the composition of those fibres. (E.g. an article consisting of "60% polyester and 40% cotton" should be ironed at the temperature indicated for polyester and without steam.) If you do not know what kind(s) of fabric(s) the article has been made of, find a spot, which will be invisible when wearing or using the article to try out the ironing temperature. (Always start at a low temperature and increase to one which gives the required results.)
• Pure woollen fabrics (100% wool) may be pressed with the iron set to a steam position. It is recommended to apply shot-of-steam and use a dry pressing cloth. When steam-ironing woollen fabrics, shining of the fabric may occur. This can be prevented by turning the article inside out and ironing the inside or by interposing a light damp cloth.
• Velvet and other textures that rapidly acquire shiny spots should be ironed in one direction only (with the nap), applying only light pressure. Always keep the iron moving.
• Iron the reverse side of synthetic materials and silk, it is not advisable to use steam as this may cause stains.

FILLING WITH WATER (FOR STEAM-IRONING)

1. Put the base on a stable surface.
2. Use the small grips (4) of the water tank to take out the water tank. Open the cap (7) and fill the water tank with clear water up to its "Max" level. Do not fill beyond this maximum level! You can use tap water, but we advise you to use distilled water.
3. Close the cap (7) of the water tank.
4. Put the water tank back in the base correctly. Make sure to keep it upright in order to avoid spilling water. Press the grips until the water tank is locked in place.
5. Never use vinegar, detergents or other chemical products.

FILLING THE WATER TANK DURING USE

As the water tank of this appliance is not under pressure, you can refill it during use. To do so, switch off the appliance, unplug it and just proceed as described above in the "Filling with water" section. When you have put the water tank back in place, plug the appliance in again, switch it on and wait until the indicator lamp of the iron goes out. Then you can start ironing again.

STEAM-IRONING

• Fill the water tank with water and insert the mains plug into a wall socket.
- As indicated on the temperature dial (5) and in the table, steam ironing is only possible at higher ironing temperatures, so set the dial to ●● or ●●●.
- Put the switch (1) in ON position ("1") and set the temperature dial of the iron (5) to the desired position. When the iron has reached the desired temperature, its pilot light (8) will go out. You can now use the steam function.
- Turn the steam control knob (12) to regulate the amount of steam. Note: the maximal steam rate ("MAX") can only be used when the ironing temperature is higher than position ●●●, or else water will drip from the sole.
- Press the steam button (6) to release steam from the soleplate of the iron. Release the button and the steam will stop. If you want a continuous jet of steam, press the steam button down and slide its transparent top part backwards so that the steam button locks. To stop the continuous jet of steam, push the transparent part of the button forwards again and release the steam button.
- When ironing, the pilot light of the iron (8) will go on and off from time to time. This means that the temperature of the iron is regulated by its thermostat. You can continue ironing. The pump pilot light will also go on and off, indicating that the steam pressure is being regulated.
- When you use a lot of steam in a very short time, the steam output is lightly reduced until your appliance produces enough steam to reduce the difference. This phenomenon also happens when there isn't enough water in the water tank.
- When the water tank is running empty, you will hear more noise when pressing the steam button. If you want to go on using the steam function, you will have to refill the water tank.

STEAMING IN A VERTICAL POSITION

Position the temperature dial on its maximum level for vertical steam ironing. The steam rate can be adjusted according to your needs.

You have to hang the cloth you want to smooth out avoiding the creases and place the iron in a vertical position at a few centimetres from the piece of cloth. Then move the iron and press the burst of steam button at the same time.

DRY IRONING

• Plug in the appliance and switch it on (power switch in position "I").
• Use the temperature dial to set the temperature needed.
• When the indicator lamp of the iron goes out for the second time, you can start ironing.
• For ironing without steam, leave the steam control knob in OFF position and do not press the steam button (6).

WHEN FINISHED IRONING

• We recommend cleaning the iron after use as follows: fill the water tank, put the temperature dial on position "LINEN" and the steam regulator on MAX and let the iron heat for 10 minutes. When the temperature has been reached, take the iron from the base, hold it vertically and keep the steam button pressed for 30 seconds, then wait 30 seconds and repeat this cycle twice.
• Switch off the appliance (power switch in position "0"), unplug the appliance and let it cool down.
  • Empty the water tank.
• We recommend placing the iron on its base when you store it. The therefore foreseen place is non-slip and will not damage the soleplate of the iron.

ANTI-CALC DEVICE

• Your appliance is equipped with an anti-calc device located inside the water tank. As a result, you can use tap water as it will be filtered by the device.
• Never use the appliance without water tank!

CLEANING

• The plastic parts of the appliance can be cleaned with a damp cloth.
- To clean the soleplate of the iron, you will find specific products in the shops. Please also read the instructions of use. Never use abrasive products to clean it.
- Never immerse the appliance in water or any other liquid.

TROUBLE-SHOOTING

Problem	Possible cause	Solution
White flour comes out of the soleplate	This is normal when the iron is new	The flour is not harmful and will disappear after a few times
Water drips from the soleplate when steam ironing	When you start steam ironing, the steam fitter is still cool and the steam will cool down	This is normal; after a few seconds, the steam jet will be OK. You can put the iron on an old cloth to start so that the water is absorbed
No steam comes out of the steam tank	The steam control knob has not been turned on or there is not enough water in the water tank	Turn the steam control knob to the desired position or fill the water tank and wait until the indicator light of the iron goes out
No steam comes out of the iron when the steam button is pressed	When ironing at a high temperature, steam with a too high temperature cannot be seen	Put a mirror under the soleplate to check if steam comes out
The soleplate is dirty	Impurities in the water adhere to the soleplate or the temperature is too high for the clothes	Clean the soleplate with a soft, damp cloth or adjust the temperature

PROTECTION OF THE ENVIRONMENT- DIRECTIVE 2002/96/EC

In order to preserve our environment and protect human health, the waste electrical and electronic equipment should be disposed of in accordance with specific rules with the

implication of both suppliers and users. For this reason, as indicated by the symbol — the rating label or on the packaging, your appliance should not be disposed of as unsorted municipal waste. The user has the right to bring it to a municipal collection point performing waste recovery by means of reuse, recycling or use for other applications in accordance with the directive.

FR MODE D'EMPLOI

POUR VOTRE SECURITE

DISPOSITIF ANTICALCAIRE

WATERRESERVOIR VULLEN (OM MET STOOM TE STRIJKEN)

SISTEMA ANTI-CALCÁRIO

PROBLEMAS E SOLUÇÕES

Copies of the I/B. Please reproduce them without any changes except under special instruction from Team International BELGIUM. The pages must be reproduced and folded in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm height). When folding, make sure you keep the good numbering when you turn the pages of the I/B. Don't change the page numbering. Keep the language integrity.

55 TKG SIS 11 - 080531

TKG SIS 11

Deutsch	4
English	10
Français	15
Nederlands	21
Español	27
Português	33
Italiano	39
Polska	45
Română	50

TEAM

Abstract black-and-white geometric shapes resembling a stylized letter 'K' with a circle inside a square (no text or symbols)

KALORIK