NoStop Prestige Eco - Iron IMETEC - Free user manual and instructions

USER MANUAL NoStop Prestige Eco IMETEC

Dear customer, IMETEC thanks you for having purchased this product. We are certain you will appreciate the quality and reliability of this appliance, designed and manufactured with customer satisfaction in mind. These instructions for use have been drawn up in accordance with European Standard EN 62079. ATTENTION! Instructions and warnings for safe use Before using this appliance, carefully read the instructions and in particular the safety warnings, which must be complied with. Keep this manual and illustrative guide with the appliance for future consultation. Should you pass the appliance on to another user, make sure to also include this documentation. NOTE: should certain parts of this booklet be difficult to understand or should doubts arise, contact the company before using the product, at the address indicated on the last page. INDEX INSTRUCTIONS FOR USE page 9 SAFETY WARNINGS page 10 SYMBOLS page 12 DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES page 12 PREPARATION page 13 USE page 13

• Cleaning the boiler page 13

• Cleaning the appliance page 14

• After having removed the appliance from its packaging, verify its integrity based on the drawing and any presence of damage caused by transport. If in doubt, do not use the appliance and contact an authorised service centre.

• Do not let children play with the packaging! Keep the plastic bag out of the reach of children - risk of suffocation!

• Before connecting the appliance, please make sure that the voltage data indicated on the identification technical data (14) correspond to those of the mains voltage. The identification technical data (14) are found on the appliance (and on the battery charger, if present).

• This appliance must be used solely for the purpose for which it was designed, namely, as a boiler iron for home use. Any other use is considered not compliant and therefore dangerous.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved or if supervised by a person responsible for their safety. Children shall not play with the appliance. The appliance cannot be cleaned or serviced by children without adult supervision. Keep the appliance and power cord away from children under 8 when the appliance is on or cooling down. DO NOT use the appliance with wet hands, damp feet or barefoot. DO NOT pull the power cable or the appliance itself to remove the plug from the socket. DO NOT expose the appliance to humidity or weather conditions (rain, sun, etc.).

• Always disconnect the appliance from the mains supply before cleaning or performing maintenance and when the appliance is not in use.EN

• If the appliance is faulty or malfunctions, switch it off and do not tamper with it. Any repairs must only be carried out by an authorised technical service centre.

• The iron must be used on a stable surface. When the iron is placed on the iron rest, make sure the support is stable. The iron must not be used if it has been dropped, if it is visibly damaged or if it leaks water.

• If the power cable is damaged it must be replaced by an authorised technical service centre, so as to prevent all risks.

• The electrical safety of this appliance is only guaranteed when it is connected correctly to an effective earthing system as required by applicable electrical safety standards. This important safety requirement must be verified and, if in doubt, request a thorough check of the system by a qualified technician.

• The electrical safety of this appliance is only guaranteed when it is connected correctly to an effective earthing system as required by applicable electrical safety standards. This important safety requirement must be verified and, if in doubt, request a thorough check of the system by a qualified technician. DO NOT immerse the iron, the power cord or the plug in any kind of liquid. DO NOT leave the hot iron in contact with easily flammable fabric. DO NOT leave the iron unattended when connected to the power supply. DO NOT dispense steam when the iron is resting on its mat. ATTENTION! Hot surface. DO NOT use chemical additives, scented substances or descaling agents.EN

IMPORTANT GUIDELINES The appliance is designed to work with tap water; however, if the water in your area is very hard, mix the tap water (50%) with distilled and/or demineralised water (50%). Salt concentration in water in certain seaside areas is very high: in such cases it is important to use “demineralised water for irons” available on the market. If in doubt, only demineralised water for steam irons must be used. Do not use diluting agents, scented liquids or descaling agents as these substances can damage the product. Do not use water from dryers, air-conditioners and rain water. The reservoir may contain some water as each product is tested before being put on the market. It is recommended to place a cloth between the iron and the fabric when using the iron for the first time. It is recommended to direct a jet of steam into the air before starting to iron, for any residual condensation to be let out. SYMBOLS WARNING PROHIBITION DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES Refer to the illustrative drawing at the beginning of this instructions booklet to verify your appliance equipment. All the figures are on the cover pages of these instructions for use

1. Reservoir water fill cover

5. Boiler cleaning LED

6. Steam (ready) LED

PREPARATION Sort the laundry according to the international symbols shown on the label; if this is missing, sort according to the type of material. Start to iron the garments that require a lower temperature so as to reduce idle time (the iron requires less time to warm up than to cool down) and eliminate the risk of burning the fabric. synthetic, acrylic, nylon, polyester: low temperatures; wool, silk: medium temperatures; cotton, linen: high temperatures; do not iron. USE

FILLING THE RESERVOIR

Lift the reservoir water fill cover (1) and fill the water reservoir without overflowing. Once finished, lower the cover (1). IRONING

• Connect the plug (8) to a suitable socket.

• Press the iron/boiler ON/OFF button (2).

• Adjust the iron temperature (10) according to the international symbols on the clothing labels and wait for the plate temperature LED (9) to go off.

• Turn the steam adjustment knob (7) to obtain the desired amount of steam.

• When the steam (ready) LED (6) lights up and remains on, you can start ironing. The plate temperature LED (9) goes on and off intermittently while ironing, thereby indicating that the appliance maintains the optimal temperature and pressure.

• Press the steam button (11) to steam iron.

• Dry iron by not pressing the steam button (11). CAUTION: TO PREVENT DROPS OF WATER LEAKING FROM THE PLATE, ONLY USE THE STEAM BUTTON (11) AT HIGH TEMPERATURES.

FILLING THE RESERVOIR WHILE IRONING

• When the water in the reservoir is below the minimum level, the no water LED (4) lights up and the iron stops producing steam.

• Lift the reservoir water fill cover (1) and fill the water reservoir without overflowing. Once finished, lower the cover (1) completely.

• The appliance is ready to continue ironing. MAINTENANCE

The boiler must be cleaned after 20 hours of operation, in order to prevent limescale from forming. The boiler cleaning LED (5) starts blinking when the boiler must be cleaned. However, you can start ironing. To clean the boiler, follow the “Sequence of operations” below.EN

ATTENTION! The boiler must only be cleaned when cold. NOTE: Failure to carry out this operation will make the warranty null and void. Sequence of operations:

• Disconnect the plug (8) from the socket.

• Place the boiler on a wash basin.

• Shake the base to help the limescale chips detach (Fig. B).

• Remove the cap cover (12) at the bottom of the boiler by turning it anti-clockwise (Fig. C).

• Loosen the cleaning cap (13) by turning it anti-clockwise with a coin (Fig. D).

• Let the water and limescale drain from the hole.

• Shake the boiler once again for the remaining water and limescale chips to come out.

• Tighten the cleaning cap (13) by turning it clockwise with a coin.

• Set the cap cover (12) in place by turning it clockwise. Do not tighten the cleaning cap (13) too tightly as the thread may be damaged. Do not clean the boiler with detergents, anti-limescale products, vinegar or any other type of substance. The boiler must be cleaned when cold, at least 4 hours after it is switched off. Once the boiler is cleaned, always fill the reservoir with water before using the boiler in order to prevent it from overheating.

CLEANING THE APPLIANCE

Switch the appliance off and disconnect the plug from the socket before cleaning. When necessary, clean the appliance with a damp cloth. Do not use solvents or other aggressive or abrasive detergents. Otherwise, the surface could be damaged. Make sure all cleaned parts are completely dry before reusing the appliance.

• Switch the appliance off by pressing the iron/boiler ON/OFF (2) button.

• Disconnect the plug (8) from the socket.

• Wait for the appliance to cool down completely before putting it away. The reservoir does not have to be emptied. NOTE: if the appliance is not going to be used for several weeks, empty the boiler completely: wait for the appliance to cool down completely and turn it over to allow all the water to flow out of the boiler.EN

TROUBLESHOOTING This chapter describes the most common problems that can arise using the appliance. If the problems cannot be solved with the information below, please contact the Authorised Assistance Centre. Problem Possible cause Solution The appliance does not go on. The household appliance is not on. Ensure that the appliance is properly connected to the socket, that the ON/ OFF button (2) is pressed and the light is on. The plate temperature LED (9) goesonando. Normal procedure. The switching ON and OFF of the LED (9) indicates the heating phase of the iron.TheLEDgoesooncetheset temperature is reached. Smoke comes out of the appliance when it is switched on forthersttime. This is absolutely normal and is due to the expansion of the plastic material. This no longer occurs after a while. Impurities come out of the plate of the new iron. This is perfectly normal in a new iron. These particles are completely harmless and will disappear after the iron is used a few times. Drops of water come out of the plate. The iron temperature adjustment knob (10) is set to a temperature that is too low for steam ironing. Adjust the temperature for steam ironing (see the ”IRONING” chapter). The appliance does not produce steam. The appliance is not on. Press the ON/OFF button (2). The steam button (11) is not being pressed. Keep the steam button (11) pressed as you iron. There is no more water in the reservoir and the no water LED (4) is on. Fill the water reservoir (see chapter

FILLING THE RESERVOIR WHILE

IRONING). The plate is dirty: there are impurities or limescale residues. The impurities or chemical substances found in the water have deposited on the plate. Wait for the plate to cool down and clean it with a damp cloth. You are ironing at a temperature that is too high. Wait for the plate to cool down and clean it with a damp cloth. An excessive amount of limescale and minerals has accumulated in the boiler. Clean the boiler (see the CLEANING THE BOILER chapter). The steam (ready) LED (6) does not light up or water leaks from the boiler cleaning cap (13). The cleaning cap (13) has not been tightened properly. Make sure the cleaning cap (13) is tightened well. Patches remain wet while ironing. Sometimes patches remain wet after being steam ironed as the steam condenses on the ironing board. Pass the iron a number of times on the wet patches without dispensing steam. If the lower part of the ironing board is wet, dry it with a dry cloth. Use a mesh ironing board to prevent the steam from condensing on the ironing board. The iron does not stay up in vertical position. The iron has been designed to be set horizontally. Place the iron on the heat resistant mat.EN

DISPOSAL The product is packaged in recyclable materials. Dispose of it in compliance with the environmental protection standards. The appliance must be disposed of in compliance with EU standard 2002/96/EC. The recyclable materials contained in the appliance must be collected to prevent environmental pollution. For further information contact the local waste authority or the appliance retailer.

ASSISTANCE AND WARRANTY

To request repairs or purchase spare parts please contact IMETEC’s authorised customer service centre on the Toll-Free Number below or via the website. The appliance is covered by the manufacturer warranty. For details, read the attached warranty sheet. Failure to comply with the instructions for use and maintenance provided in this manual will render the manufacturer’s warranty null and void. www. imetec.com Tenacta Group S.p.A. Via Piemonte 5/11 24052 Azzano S. Paolo (BG) ITALY Tel. +39.035.688.111 Fax +39.035.320.149 MI001553 0214 (MMYY)FR