LH2705 - Lighting BRENNENSTUHL - Free user manual and instructions

Brand	Brennenstuhl
Model	LH2705 (also SH2705)
Product Type	Premium City LED spotlight / lamp
Variants	LH2705, SH2705, LH2705 PIR, SH2705 PIR
Rated Voltage	220-240 V~ 50/60 Hz
Rated Power	13.5 W (27 LEDs of 0.5 W)
Protection Type	IP44
Protection Class	I
Motion Detector (PIR models)	Yes, max. range 10 m, adjustable
Detection Angle	180° (estimated)
Delay Time Adjustment	10 s ± 5 s to 4 min ± 1 min
Brightness Threshold Adjustment (LUX)	Adjustable, with day/night function
Ambient Temperature	-15 °C to +45 °C
Recommended Mounting Height	1.8 to 2.5 m above ground
Minimum Distance from Lit Objects	1 m
Maintenance and Cleaning	Dry or slightly damp cloth, no solvents
LED Replacement	Non-replaceable
Cover Replacement	Only original Brennenstuhl protective glass
Electrical Wiring	N = blue, PE = green/yellow, L = brown
Disposal	In accordance with WEEE directive (2012/19/EU)
Manufacturer	Brennenstuhl, Seestraße 1-3, 72074 Tübingen, Germany

Frequently Asked Questions - LH2705 BRENNENSTUHL

How to install the LH2705 lamp?

Loosen the screw on the connection box, press the release button and remove the mounting plate. Mark the holes, drill avoiding hidden cables, then fix the plate with plugs and screws. Connect the electrical cable (N blue, PE green/yellow, L brown) to the terminal block. Put the lamp body back on the plate until it clicks and tighten the screw. Important: installation must be carried out by a qualified professional.

How to adjust the motion detector?

The detector has two controls: TIME (delay from 10 s to 4 min) and LUX (brightness threshold). To adjust the range, orient the sensor and have a person cross the area. Set TIME to the desired duration. To make the lamp only turn on at night, turn LUX from the sun symbol towards the moon symbol. Tip: by slowly turning LUX while moving, you can adjust the twilight threshold.

What to do if the light does not turn on when motion is detected?

First check the power supply (fuses/switchboard). Make sure no other light source prevents the detector from sensing darkness. Also check the LUX control setting: if it is too low, the lamp will not turn on. Reorient the sensor if necessary.

What is the range of the motion detector?

The maximum range is 10 meters, but it may vary depending on the mounting height and location. Cross movements are detected better than direct approach movements.

Can I replace the LEDs?

No, the LEDs are integrated and cannot be replaced. In case of failure, the lamp must be replaced. For broken covers, use only original Brennenstuhl protective glass.

What does the IP44 protection rating mean?

IP44 means the housing is protected against solid bodies larger than 1 mm (tools, wires) and against splashing water from all directions. The lamp is therefore suitable for outdoor use.

How to clean the lamp?

Use a soft, dry or slightly damp cloth. Never use solvents, corrosive or aggressive cleaning products. Wait for the lamp to be switched off and cooled down before cleaning.

Can I use this lamp indoors?

Yes, IP44 allows use outdoors as well as in humid indoor environments (bathroom, cellar). However, the lamp is designed for normal use and not for intensive applications.

What is the ideal mounting height?

The recommended height is 1.8 to 2.5 meters above ground. Mount the lamp on a stable, dry surface. Maintain a distance of at least 1 meter from lit materials to avoid fire hazard.

How to adjust the daylight sensitivity?

Turn the LUX control towards the sun symbol (*) for the detector to respond day and night, or towards the moon symbol (C) to operate only at night. For fine adjustment, wait for the desired light level, then slowly turn the control until the lamp turns on upon movement.

USER MANUAL LH2705 BRENNENSTUHL

GB Installation and Operating Instructions Premium LED spotlight /zone lighting

MODEL
LED spotlight Premium City SH 2705 PIR IP 44,
LED zone lighting Premium City LH 2705 PIR IP 44,
LED spotlight Premium City SH 2705 IP 44,
LED zone lighting Premium City LH 2705 IP 44

PARTS DESCRIPTION (see Fig. A)

Screw for terminal box
Lustrerterminal
3Unlockbutton
Assemblyplate
Screws for assembly plate
6 Cablebushing
Dowels
Motion detector (model SH 2705 PIR IP 44 and LH 2705 PIR IP 44)

SAFETY INSTRUCTIONS

Notice: Please read the following instructions before your install the lamp. Make sure that the current is shut off before you connect the lamp. The lamp may only be installed by a qualified professional.

Warning: This lamp may not be used without all of the o-rings properly installed! LED lamps are extremely bright. Under no circumstance should you look into the LED lamp as this can cause permanent damage to the eyes.

RISK OF FIRE! Assemble the lamp at a minimum distance of 1 m to the material being illuminated. Excessive heat development can lead to fire.

$$ \dots - 1 m \vert $$

A broken LED cover must be replaced with a Brennenstuhl LED protection disc prior to continuing to use the lamp.

RISK OF BURN INJURY! Make sure that the lamp is switched off and cool before you touch it.

Operating Instructions Premium LED spotlight /zone lighting

TECHNICAL DATA

Nominal voltage: 220 - 240V 50 / 60Hz

Nominal power: 27 × 0.5 W LED

Protection type: IP 44

Protection class: I

The LED lamp is solely for normal use and not designed for raw operation.

Motion detector range: 180^ and max. 10 meter, adjustable

Duration: adjustable from 10 (+ / - 5) seconds up to 4 (+ / - 1) minutes

Ambient temperature: -15^ + 45^

INSTALLATION

Notice: The lamp must be installed on a dry, stable and solid surface in accordance with the specifications in Fig. B. Ideally, the LED lamp should be installed 1.8 to 2.5 above the ground (see Fig. B).

Install the lamp (see Fig. A)

Release the screw 1 on the terminal box, press the unlock button 3 and remove the assembly plate 4. Use the assembly plate to mark the positions of the screw holes on the assembly surface.

Important: Make sure not to drill into any hidden lines. Guide the power cable through the cable bushing ⑥ on the assembly plate and attach it to the wall using the screws ⑤ and dowels ⑦. Attach the power cable to the lustre terminal ② in accordance with Fig. A (N = blue cable, 12 = green/yellow cable, L = brown cable).

Reattach the body of the lamp to the assembly plate. To do this, press the unlock button 3 and slide the lamp onto the assembly plate until the unlock button 3 locks back into place. Secure the connection by screwing it to the terminal box 1.

Set the desired direction of the light and tighten the screws. Switch the main power supply on.

Only for model SH 2705 PIR IP 44 and LH 2705 PIR IP 44

The motion detector should not be directed at heat sources such as grills, air conditioners, other outside lighting, moving cars and exhaust shafts in order to avoid annoying false triggering. For the same reason, the motion detector should not be installed in areas with strong electromagnetic interference. Do not direct the device at reflective surfaces such as smooth white walls, swimming pools, etc.

The technical specifications for the sensor range (max. 10 meter at 180^ ) can vary slightly depending on the installation height and location. The sensor range on the device can also change if the temperature changes. Before you select the installation location for the device, you should know that the motion detector reacts most sensitively to movements that run straight across its range and least sensitively to movements that run directly toward or away from the motion detector (see Fig. C). If the movement is directly toward or away from it, this means a significant reduction of the sensor range (see Fig. C).

SETTING THE MOTION DETECTOR (Only for model SH 2705 PIR IP 44 and LH 2705 PIR IP 44)

There are two controllers on the motion detector (see Fig. D)

Time setting (TIME):

The length of the duration that the lamp remains on after activation can be set to between 10 (+/-5) seconds and 4 (+/-1) minutes. By turning the TIME controller from (+) to (-) , the duration is shortened.

Notice: If the light has been triggered by the motion detector, the duration restarts with each detection.

Light setting (LUX):

The LUX controller has an integrated sensor device (photocell) that recognises daylight and darkness. Symbol () means that the motion detector is triggered during the day and at night and when set at the () symbol, it only reacts at night.

Setting the controllers (see Fig. D)

Set the LUX controller to the (※) symbol and wait for a few seconds. Make sure that the TIME controller is set to minimum (-) . The lamp will now turn on and remain on for several seconds.

Direct the motion detector so that the desired area is within its range. Have a person walk across the area to be detected and change the sensor angle until the lamp turns on from the movement (see Fig. C). Set the TIME controller to the desired time.

To set the LUX threshold, at which the light should automatically turn on at night, turn the LUX controller from daylight to night. Notice: If the light needs to be turned on earlier, e.g., at dusk, wait for the desired light level, then slowly turn the LUX controller toward the daylight position while someone walks through the centre of the sensor range. Let the controller go when the light turns on.

MAINTENANCE AND CLEANING

The LED lamp does not contain any components that require maintenance. The LEDs cannot be replaced. To clean, use only a dry or lightly moistened cloth and do not use any cleaning solvents, acidic cleaning agents, etc.

DISPOSAL

Dispose of electrical devices in an environmentally responsible manner!

Do not dispose of electrical devices with household rubbish

In accordance with Directive 2012/19/EU on waste electrical and electronic equipment, used electrical equipment must be collected separately and reused or recycled in an environmentally responsible manner. Please contact your local authorities for available disposal options for your worn-out device.

Operating Instructions Premium LED spotlight /zone lighting

TROUBLESHOOTING AND USER INSTRUCTIONS

Problem Possible cause Possible solution

Light does not go on from motion within the sensor range.	1.Nopower. Check all connections and fuses/switches.
	2. Lighting close up is too bright.	Redirect the motion detector or change the device's location.
	3. Controller set incorrectly. Adjust sensor angle or controller.
The light goes on for no apparent reason (false trigger)	1. Heat sources such as air conditioners, ventilation openings, heating equipment outlets, grills, other outdoor lighting or moving cars activate the motion detector.	Adjust the sensor head away from these sources.
	2. Animals/birds or pets. Readjusting the sensor head can be helpful.
	3. Reflections from swimming pools or reflective surfaces.	Readjust the motion detector.

Notice: Under cold weather conditions, all devices with PIR sensors are more sensitive than in warm weather.

MANUFACTURER

LED-spot Premium City SH 2705 PIR IP 44,

LED-lamp Premium City LH 2705 PIR IP 44,

LED-spot Premium City SH 2705 IP 44,

LED-lamp Premium City LH 2705 IP 44

BESCHRIJVING VAN ONDERDELEN (zie afb. A)

VEILIGHEIDSWAARSCHUWINGEN

Nominal guc: 27 × 0.5 W LED

PpOβoλεaC LED Premium City SH 2705 PIR IP 44,

Φavoc LED Premium City LH 2705 PIR IP 44,

PpOBoλεaC LED Premium City SH 2705 IP 44,

Φavoc LED Premium City LH 2705 IP 44

NEPIRPAΦH EAPTHMATΩN (βλ. εικ.Α)

Iba pre model SH 2705 PIR IP 44 a LH 2705 PIR IP 44

LED Iampa Premium City LH 2705 PIR IP 44,

LED prozektors Premium City SH 2705 IP 44,

LED Iampa Premium City LH 2705 IP 44

DETAU SARAKSTS (skat. A att.)

Piesleguma karbas skruve
Piesleguma spailes
3Atblokešanas taustinš
Montañas plaksne
Montazasplaksnes skruves
6 Vada izvades vieta
Dibeli
Kustibu sensors (model SH 2705 PIR IP 44 un LH 2705 PIR IP 44)

DROŠIBAS NORADIJUMI

Piezime: pirms gaismekla uzstadiisanas, ludzu, izlasiet sos noradijumus. Pirms gaismekla pieslegsanas elektrotiklam parliecinieties, ka strvas padeve ir izslegta. Gaismekla uzstadiisanu drikst veikt tikai kvalificets specialists.

Bridinajums: so gaismekli nedrikst izmantot, ja nav atbilsto uzstaditi visi blivgredzeni! LED gaismekli ir loti spilgti. Nekadā gadijumā neskatieties uz gaismas avotu, jo tas var radit neatgriezeniskus redzes bojāumus.

AIZDEGSANAS RISKS! Montejiet gaismekli vismaz 1 m attalumā no apgaismotā materiaīla. Parak augsta temperatura var izraisit aizdegsanos.

Ja LED gaismekla aizsargstikls ir saplisis, pirms turpmakas lietošanas to nepieciesams aizstat ar originalu Brennenstuhl LED aizsargstiklu.

APDEGUMURISKS! Pirms pieskaraties gaismeklim, izsledziet to un parliecinieties, ka tas ir atdzis.

Lietosanas instrukcija LEDprozektors/lampa Premium

TEHNISKIE DATI

Spiregums: 220 - 240V 50 / 60Hz

Nominalā jauda: 27 x 0,5 W LED