F400 - Smoke machine BOOMTONEDJ - Free user manual and instructions

Product Type	Smoke Machine
Brand	BOOMTONEDJ
Model	F400
Dimensions (L x W x H)	280 x 130 x 135 mm
Weight	1.55 kg
Power Supply	230 VAC, 50-60 Hz
Power Consumption	400 W
Tank Capacity	0.25 L
Smoke Output	2,000 ft³/min (50 m³/min)
Heating Time	Approximately 4 minutes
Recommended Fluid Type	BoomtonDJ Smoke Fluid
Electrical Protection	Power cable with ground
Safety	Do not touch during operation; do not use in rain or humid environments; max ambient temperature 40°C
Installation	Must be installed by a qualified person, with a sturdy hook and safety sling; the structure must support 10 times the weight of the device
Maintenance	Clean with mineral or distilled water; never use tap water
Repairability	No user-replaceable parts; contact an authorized repairer
Included Accessories	Remote control with red button
Intended Use	Smoke production for visual effects

Frequently Asked Questions - F400 BOOMTONEDJ

How to fill the tank of the F400 smoke machine?

Open the tank cap and pour smoke fluid (preferably BoomtonDJ brand) up to the maximum level. Do not exceed the 0.25 L capacity.

What is the heating time of the machine?

The heating time is approximately 4 minutes for the first warm-up. The remote control indicator lights up when the machine is ready.

What to do if the machine does not produce smoke?

Check that the machine is plugged in and turned on, that the tank contains fluid, and that the heating time has elapsed. If the remote control does not light up, let it heat longer. If the problem persists, contact an authorized repairer.

The remote control does not work, what to do?

Ensure the machine is up to temperature (indicator on). If the indicator is off, the machine is still heating. If the indicator is on but the remote control does not trigger smoke, check the remote control connection or replace it.

How to clean the F400 smoke machine?

Empty the tank of any fluid, fill it with mineral or distilled water (about 1 L), turn on the machine, set the flow to maximum and let it run for 15 minutes. Then turn it off, let it cool, and drain the excess water. Never use tap water.

What safety precautions must be followed?

Do not touch the device during operation as it gets very hot. Do not obstruct the smoke outlet. Do not use in rain or humid environments. Install the machine with a sturdy hook and safety sling. Disconnect it before any intervention.

What type of fluid should I use?

Use exclusively smoke fluid specially designed for smoke machines, preferably BoomtonDJ brand. Unsuitable fluids may damage the device.

What is the required power supply?

The machine requires a mains outlet 230 VAC, 50-60 Hz with ground. Do not connect it to a dimmer pack.

At what height should the machine be installed?

The machine must be installed out of reach of the public, securely fixed to a hook capable of supporting at least 10 times its weight (15.5 kg). Use a safety sling.

How often should I clean the machine?

Clean the machine as soon as the smoke volume decreases or after several hours of use. Regular maintenance with distilled water extends the device's lifespan.

USER MANUAL F400 BOOMTONEDJ

Line drawing of a portable industrial machine with ventilation slots and control knobs (no text or symbols)

F400

1- Safety Instructions

WARNING

Please read the instructions carefully which include important information about the installation, operation and maintenance.

• Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that he also receives this instruction booklet.
• Unpack and check carefully there is no transportation damage before using the fixture.
• It's important to ground the yellow/green conductor to earth in order to avoid electric shock.
• Disconnect main power before servicing and maintenance.
• Maximum ambient temperature is Ta: 40°C. Don't operate it where the temperature is higher than this.
• In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. There are no user serviceable parts inside the fixture.
• Do not connect the device to any dimmer pack.
• To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
• Do not look directly at the LED light beam while the fixture is on.
• Do not touch any wire during operation.
• The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit's weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

• The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

• WARNING: This device operates under high temperatures. Do not touch the fog machine while active or directly after use. Do not block the fog exit with your hands. Incorrect use may cause serious first or second degree burns.

• WARNING: A cooling down time of 20 minutes is obligatory after use, to cool down the housing and internal components.
• WARNING: Do not physically move the machine while in use.
• IMPORTANT: It is possible that small amounts of fog are produced during the warming-up time and after use.

2- How to use the unit

1- Fill the liquid tank.
2- Connect main power supply.
3- Turn ON the Smoke machine.
4- Wait about 5 minutes, for the 1st warm-up.
5-The remote control LED is now ON, you can use the machine by pressing the remote control button.

3- Technical Specifications

Smoke output : 2,000 cu.ft per minute

Warm up time : approx. 4 min

Tank capacity : 0.25L

Power consumption: 400W

Power supply : 230Vac, 50-60Hz

Dimensions : 280 x 130 x 135mm

Weight : 1.55Kgs

4-Clogged system

It is possible that the fog output of your machine decreases over time. This may be caused by congestion in the fluid pump system. To solve this, you have to follow the steps described below first. Do not use special fog machine cleaning solutions first, as these are the last expedients to save your fog machine. - If there is any fog liquid left in your tank, remove it from the tank. - Fill the fluid tank with demineralized/distilled water.

WARNING: Never use tap or normal bottled water as this contains chalk. This may clog your system, causing permanent damage.

• Fill the tank with approximately 1 liter demineralized/distilled water.
• Turn on the machine and let the heating process take place
• When your fog machine is ready, let the machine work at 100% output, continuously.
• You will notice that the first couple of output-bursts the machine mainly produces fog. This is caused due to the fog liquid that is still inside the pipes of the heating system. After several minutes you will notice that the fog output smoothly transforms into a light steam solution. This means that the demineralized or distilled water has been pumped around the machine.
• Let the machine perform at full output for approximately 20 minutes, to make sure any internal dirt is removed when possible.
• Turn off the machine and let it cool down. Remove the demineralized/distilled water from the tank.

IMPORTANT: You can save the demineralized/distilled water that was not used, but only use it again for fog machine cleaning purposes, as traces of fog liquid have mixed with the water inside the tank.

NOTE: When the machine will not be used in the near future, you may leave the tank empty. The demineralized/distilled water will stay inside the machine, which is harmless. - Fill the machine with fog liquid and turn it back on. Let the heating process take place. When the fog machine is ready, let it perform at 100% output. You will notice that the machine produces steam, which will smoothly transform into fog as the fog liquid is pumped through the system.

BoomToneDJ.com

www.boomtonedj.com