14910SL2-4 - Dishwasher PROLINE - Free user manual and instructions

Product type	Freestanding dishwasher
Brand	PROLINE
Model	14910SL2-4
Capacity	9 place settings
Dimensions (H x W x D)	84 x 45 x 60 cm
Electrical supply	220-240 V ~ 50 Hz, 1850 W
Energy class	E
Water consumption (eco program)	10.0 L/cycle
Energy consumption (eco program)	0.704 kWh/cycle
Duration of eco program	4 h 00 min
Noise level	47 dB(A) - class C
Water pressure allowed	0.04 - 1.00 MPa
Wash programs	Intensive, Eco, Glasses, 1h, Quick wash, Pre-wash
Special functions	Delay start (1-24 h), Child lock, 3-in-1 function
Tub type	Stainless steel
Water softener	Adjustable (7 levels)
Cleaning and maintenance	Removable filters, detachable spray arms
Installation	Cold water connection, drain up to 1 m height
Warranty	2 years
After-sales service	FNAC DARTY - Spare parts within 15 working days

Frequently Asked Questions - 14910SL2-4 PROLINE

How to adjust the water softener?

To adjust the softener, hold down the Menu and P buttons for 5 seconds until 'H4' appears. Press Menu to select the level appropriate for your water hardness (H0 to H7), then confirm with P.

What to do if the dishwasher does not start?

Check that the appliance is turned on, the door is properly closed, and the cord is plugged in. Make sure the fuse has not blown and the water supply is open.

How to use the 3-in-1 function?

This function is activated for the Intensive, Eco or Glass programs. Press the 3-in-1 button; the indicator flashes, then press Start to confirm. It allows the use of all-in-one tablets without salt or rinse aid.

How to clean the filters?

Turn the filter assembly counterclockwise, lift it out, then separate the three elements (flat filter, coarse debris filter, micro-filter). Rinse them under running water with a soft brush. Reassemble by turning clockwise.

Why is my dishes not clean?

Possible causes: incorrect loading (dishes touching), program too light, insufficient detergent, blocked spray arms or clogged filters. Consult the loading guide and choose a more intense program if necessary.

How to activate child lock?

Hold down both Menu and P buttons simultaneously for more than 3 seconds. The lock indicator lights up. To deactivate, repeat the same operation.

What is the minimum and maximum water pressure?

The water supply pressure must be between 0.04 MPa (minimum) and 1.00 MPa (maximum).

How to add salt and rinse aid?

For salt: remove the lower basket, unscrew the cap of the salt reservoir, pour about 1.2 kg of specific salt then fill with water to the brim. For rinse aid: unscrew the cap of the dispenser and pour until the indicator is black.

What do error codes mean?

Common codes: E1 (door open), E2 (water inlet problem), E3 (drain problem), E4 (temperature sensor), E5 (overflow), E6 (leak), E7 (heating element). In case of leak, turn off the water before intervening.

How to maintain the appliance during prolonged non-use?

Run an empty cycle, unplug the appliance, turn off the water supply and leave the door slightly open to avoid odors and preserve the seals.

USER MANUAL 14910SL2-4 PROLINE

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675166

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675167

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675166

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675167

Nominale spanning / frequentie	220-240V ~ 50Hz
Nominaal vermogen	1850W
Waterdruk	0,04 - 1,00 MPa

DIENST VOOR HERSTELLINGEN EN RESERVEONDERDELEN

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675166

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675167

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ THE FOLLOWING SAFETY WARNINGS AND THE INSTRUCTIONS CAREFULLY BEFORE USING THE APPLIANCE AND KEEP FOR FUTURE REFERENCE.

Warnings

• This appliance is intended to be used in household and similar applications such as:

• staff kitchen areas in shops, offices and other working environments;

• farm houses;
• by clients in hotels, motels and other residential type environments;

• bed and breakfast type environments.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

• Regarding the instructions for the method and frequency of cleaning, refer to the section "CLEANING AND MAINTENANCE" in pages 126-129
  The openings must not be obstructed by a carpet.
• The new hose-sets supplied with the appliance are to be used; old hose-sets should not be reused.
• The maximum number of place settings to be washed by this dishwasher is 9 place settings.

• The door should not be left in the open position since this could present a tripping hazard.

• Regarding the detailed instructions on how to load the dishwasher, refer to the section "Loading the dishwasher" in pages 112-113.
  WARNING: Knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position.

• The minimum permissible inlet water pressure is 0.04MPa . The maximum permissible inlet water pressure is 1MPa .
• The plug must be remained easily accessible after installation of the appliance.

Safety Precautions

• Installation and repair can only be carried out by a qualified technician.
  This appliance is for indoor household use only.
• To protect against the risk of electrical shock, do not immerse the appliance, cord or plug in water or any other liquid.
• Turn off and unplug the appliance before cleaning and performing maintenance.
• Do not sit on, or stand on the door or dish rack of the dishwasher.
• Do not operate your dishwasher unless all enclosure panels are properly in place.
• Carefully open the door when the dishwasher is operating because there might be a risk of water squirting out.
• Do not place any heavy object on or stand on the door when it is open. The appliance could tip forward.
• Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children away from the dishwasher when the door is open.
• Do not wash plastic items unless they are marked "dishwasher safe" or the equivalent.

• Use only detergent and rinse agents recommended for use in an automatic dishwasher.

• Never use soap, laundry detergent, or hand washing detergent in your dishwasher.

• The door should not be left open, since this could increase the risk of tripping.
• Do not tamper with controls.

Earthing Instructions:

• This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of an electric shock by providing a path of least resistance of electric current. This appliance is equipped with an earthing conductor plug.
• The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.
• Improper connection of the equipment-earthing conductor can result in the risk of an electric shock.
• Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.
• Do not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician.

PRODUCT OVERVIEW

Control Panel

106

FR

NL

PT

EN

Program indicator lights

Eco			1h	ER
Intensive	Eco	Glass	60 minutes	Rapid	Pre-wash

Display: To show washing program time, delayed start time, water hardness setting and error codes

Indicator lights

3-in-1 Tablet detergent	Child lock	Washing	Drying	Refill rinse aid	Refill salt

BEFORE INSTALLING YOUR DISHWASHER

Before connecting your dishwasher to the power supply, check that the voltage stated on the rating label of your appliance corresponds to the voltage in your home. The appliance must be grounded. The manufacturer is not responsible for damages that may occur as a result of usage without grounding.

WARNING:

Disconnect electrical power before installing your dishwasher.

INSTALLATION INSTRUCTIONS

Your dishwasher can be installed in various locations in your kitchen as long as there is space and accessibility to connect your dishwasher to the water/ drainage and electrical supply.

Do not connect an extension lead to the appliance to avoid potential safety hazards.

Cold Water Connection

The installation of the hose should be done by professionals.

Connect the supplied water supply hose to a threaded 3 / 4'' connector and make

sure that it is fastened tightly in place.

If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear. This precaution is needed to avoid the risk of the water inlet to be blocked and damage the appliance.

Connection of the Drain Hose

Insert the drain hose into a drain pipe with a minimum diameter of 4cm , or let it run into the sink, making sure to avoid bending or crimping it. The height of drain pipe must be less than 1000mm . The free end of the hose must not be immersed in water to avoid the back flow of it.

108

FR

NL

PT

EN

Please securely fix the drain hose in either position A or position B.

The installation of the hose should be done by professionals.

If leaks are detected, immediately shut the water supply and check the hose connections fully. Re-tighten the connections if necessary.

If for any reason you are unable to stop the leak yourself, please seek advice from a qualified plumber.

Electrical Connection

The installation of electrical equipment should be done by professionals.

• Do not use an extension cord or an adapter plug with this appliance.
• Do not, under any circumstances, cut or remove the earthing connection from the power cord.

Ensure the voltage and frequency of the dishwasher correspond to those indicated on the rating plate. Only insert the plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the socket, rather than using a adaptors or the like as they could cause overheating and burns.

Ensure that proper earthing exists before use.

Levelling

Place the dishwasher on an even, stable surface.

It is very important that the dishwasher is perfectly levelled in order to avoid the dishwasher to malfunction. You can level the dishwasher by adjusting the base feet.

110

FR

NL

PT

EN

BEFORE LOADING THE BASKETS

• Remove coarse food remains, e.g. bones, which may clog the filter or damage the wash pump.
• Soak any pots or pans with burnt-on food remains on the bottom then load them into the basket.

WARNING:

• Make sure that the dishes are securely in place so that they cannot tip over or obstruct the rotation of the spray arms during the washing cycle.
• Containers such as cups, bowls, glasses and pots should always be loaded with the opening facing downwards and with any cavities at an angle, to allow the water to drain out.
• Do not stack dishes.
• Do not place glasses too close together because they may knock against each other and break.
• Load large items which are most difficult to clean into the lower basket.
  Make sure that the items being washed are dishwasher-safe.

Items which are not dishwasher-safe:

Wooden dishes, pots or pans
Handcrafted items
- Plastic dishes (except when marked dishwasher-safe)
Dishes and objects in copper, tin, zinc or brass
Aluminium dishes
Silverware
Glass and crystal
- Decorated items

LOADING THE DISHWASHER

Loading the Upper and Lower Baskets

• The upper basket is designed to hold delicate and light items such as glasses, cups, saucers, serving bowls and shallow pans.
• The lower basket is designed to take saucepans, lids, plates, salad bowls, cutlery etc.
• Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the upper spray arm can turn freely.
• Arrange items so that water can reach all surfaces.

A. Cups
B. Glasses
C. Saucers
D. Mugs
E. Dessert bowls
F. Small pot
G. Cutlery basket

H. Soup plates
I. Dinner plates
J. Dessert plates
K. Oval platter
L. Glass bowl
M. Melamine dessert plates
N. Melamine bowl

112

FR

NL

PT

EN

Cultery Basket
1

1. Teaspoons
2. Dessert spoons
3. Soup spoons

4. Forks

5. Knives

6. Serving fork
7. Gravy ladle

Do not let any item extend through the bottom.

Always load sharp utensils with the sharp point down!

FR

NL

PT

EN

113

ADJUSTING THE UPPER BASKET

1. Pull out the upper basket.

1. Re-attach the upper basket to upper or lower rollers.

1. Remove the upper basket.

1. Push in the upper basket.

FOLDING SPIKES

The spikes of the lower basket are used to hold plates and a platter.

They can be folded down to make more room for large items.

114

FR

NL

PT

EN

USING THE WATER SOFTENER

The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will be formed on the utensils. This appliance is equipped with a water softener which uses a salt specifically designed to eliminate the minerals from the water.

CAUTION:

Only use salt specially formulated for domestic dishwashers.
- Do not use table salt as it contains insoluble substances which may damage the water softening system.
- Fill the salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion.

Adjusting the salt consumption

1. After the dishwasher is switched on, enter the status of adjusting the salt consumption by holding down and P for about 5 seconds until the display shows "H4".
2. Repeatedly press to adjust the setting to suit the water hardness.
3. Press P to validate settings.

WATER HARDNESS			Display
°Clarke	Range	Mmol/l
0 - 8	Soft	0 - 1,1	H0
9 - 10	Soft	1,2 - 1,4	H1
11 - 12	Medium	1,5 - 1,8	H2
13 - 15	Medium	1,9 - 2,1	H3
16 - 20	Medium	2,2 - 2,9	H4
21 - 26	Hard	3,0 - 3,7	H5
27 - 38	Hard	3,8 - 5,4	H6
39 - 62	Hard	5,5 - 8,9	H7

Factory setting : H4

Salt is not required when the setting is at H0.

FR

NL

PT

EN

115

Filling with salt

The salt container must be refilled when the salt warning light illuminates.

1. Remove the lower basket and unscrew the cap from the salt container.
2. Place the end of the funnel (supplied) into the hole and pour in about 1,2kg dishwasher salt.
3. Fill the salt container to its maximum limit with water. It is normal for small amount of water to come out of the salt container.
4. Screw back the cap tightly.
5. Remove any salt that has fallen around the opening of the container and into the tub.

WARNING!

Salt is corrosive, it is strongly recommended to run a shortest program without dishes after each salt container filling to wash away any salt that may have been spilled into the tub.

NOTE: Depending on how well the salt dissolves, the salt warning light may still be on even though the salt container is filled.

USING THE RINSE AID AND DETERGENT DISPENSERS

Function of the rinse aid

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can leave spots and streaks. It also improves drying by allowing water to roll off the dishes.

WARNING! Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances (e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.

Function of the detergent

The chemical ingredients that compose the detergent are necessary to remove, crush and dispense all dirt out of the dishwasher.

WARNING!

Proper use of detergent

Use only detergent specifically made for dishwasher use.

Keep your detergent fresh and dry.

Do not put powdered detergent into the dispenser until you are ready to wash dishes.

• Dishwasher detergent is corrosive! Keep it out of the reach of children.

Refilling the rinse aid dispenser

Unless the rinse-aid warning light on the control panel is on, you can always estimate the amount from the color of the rinse-aid indicator. When the rinse-aid container is full, the indicator will be fully dark. The size of the dark dot decreases as the rinse-aid diminishes. You should never let the rinse aid level be less than 1/4 full.

As the rinse aid diminishes, the size of the black dot on the rinse aid indicator changes, as illustrated below.

Full

3/4 full

1/2 full

1/4 full

Empty

FR

NL

PT

EN

117

Filling the rinse aid dispenser

1. Remove the rinse aid dispenser cap by rotating it anticlockwise.

2. Pour the rinse aid into the dispenser, being careful not to overfill.

3. Close the rinse aid dispenser cap by rotating it clockwise.

NOTE: Clean up any spilled rinse aid with an absorbent cloth to avoid excessive foaming during the next wash.

118

FR

NL

PT

EN

118

Adjusting the rinse aid dispenser

The rinse aid reservoir has six settings. The higher the number, the more rinse aid the dishwasher uses.

If the dishes are not drying properly or are spotted, adjust the dial to the next higher number until your dishes are spotfree.

Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or knife blades.

Filling the detergent dispenser

1. Open the detergent dispenser cover by pushing the release catch.

2. Add detergent into the larger cavity (A) for the main wash cycle.

For more heavily soiled wash loads, also add some detergent into the smaller cavity (B) for the pre-wash cycle.

1. Close the cover and press on it until it locks into place.

WASHING PROGRAMS

Program	Type of Dishes	Cycle Description	Detergent Pre/Main	Program duration (min)	Energy (kWh)	Water consumption (L)	Rinse aid needed?
	For heavily soiled crockery with or without dried-on food	Pre-wash Main Wash(62°C) Rinse1 Rinse2 Hot Rinse Drying	3 / 14 g (or 3-in-1)	170	1,20	16,4	Yes
Eco	Standard cycle for normally soiled loads such as pots, plates, glasses and lightly soiled pans	Pre-wash Main Wash (46°C) Hot Rinse Drying	3 / 14 g (or 3-in-1)	240	0,704	10,0	Yes
	For lightly Soiled crockery and glass	Main Wash(45°C) Rinse Hot Rinse Drying	12 g (or 3-in-1)	82	0,76	10,0	Yes
1h	For normally soiled loads that need quick wash	Pre-wash Main Wash (60°C) Hot Rinse Drying	3 / 12 g	60	0,84	10,0	Yes
ER	A shorter wash for lightly soiled loads that do not need drying	Main Wash (45°C) Hot Rinse	10 g	40	0,60	6,8	No
	To rinse out loosen soil particles from the dishes	Pre-wash	N.A.	13	0,01	3,6	No

NOTE:

EN 60436: This program is the test cycle. The information for comparability test is in accordance with EN 60436.

• The eco programme is suitable to clean normally soiled tableware, that for this use, it is the most efficient programme in terms of its combined energy and water consumption, and that it is used to assess compliance with the EU ecodesign legislation.
• Loading the household dishwasher up to the capacity indicated by the manufacturer will contribute to energy and water savings.

120

FR

NL

PT

EN

• Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended.
• Washing tableware in a household dishwasher usually consumes less energy and water in the use phase than hand dishwashing when the household dishwasher is used according to the manufacturer's instructions.
• The values given for programmes other than the eco programme are indicative only.

FR

NL

PT

EN

STARTING A WASH CYCLE

1. Turn the water tap on.
2. Open the dishwasher door.

3. Check the filters.

4. Ensure that they are clean and properly positioned. See the section Cleaning and Maintenance.

5. Check that there is rinse aid and salt.

6. Load the dishes.

7. Ensure that the spray arms can rotate freely.

8. Add the required amount of detergent into the dispenser according to the Washing Program chart.

9. Close the dishwasher door securely.
10. Press to switch on the dishwasher.

11. Repeatedly press P to select the desired washing program.

12. The corresponding programme indicator light will flash.
    Delay Timer:

The delay timer allows you to delay the start of a washing program from 1 hour up to 24 hours.

Repeatedly press until the desired delayed start time is shown on the display, e.g. 3H for a 3-hour delay.

Once the delay timer has been set, press to activate the function. To cancel the delayed start, press .

1. Use 3-in-1 function :

Your dishwasher has a 3-in-1 function which does not need salt and rinse-aid but a 3-in-1 detergent tablet for cleaning your dishes.

When using a 3-in-1 detergent tablet, the rinse-aid and salt indicator lights are no longer. It may be

helpful to select the lowest possible setting for water hardness.

Before using 3-in-1 detergent tablets you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers instructions (on the product packaging).

Detergent tablets of different brands dissolve at different speeds. For this reason some detergent cannot dissolve and develop their full cleaning power during

122

FR

NL

PT

EN

short cycles.

Therefore please use long cycles when using detergent tablets, to ensure the complete removal of detergent residuals.

This function can only be selected on Intensive, Eco or Glass program only.

To select "3-in-1" function:

a. Press and the corresponding indicator light will flash on the display.

b. The 3-in-1 washing cycle will be available after pressing and the indicator light will stop flashing.

To cancel "3-in-1" function:

To cancel the 3-in-1 washing cycle, please follow the "Changing the program in progress" instructions.

If you decide to switch to the use of a standard detergent system, it is recommended that you:

a. Refill both the salt and rinse aid compartments.
b. Switch the water hardness setting to the highest possible position and run for three normal cycles without load.
c. Readjust the water hardness setting again according to the conditions for your region (For more information please refer to your instruction manual).

1. Press to start washing.

2. The programme indicator light will stop flashing.

3. If delay timer is set, the selected delay hour indicator light will illuminate. After the delay time has elapsed the appliance will automatically operate.

4. After the program has ended, the diswasher will buzz and stop.

5. Wait for a few minutes before you open the dishwasher door in order to avoid burns.

6. Open the door carefully. Hot steam may escape when the door is opened!

7. Open the dishwasher door, leave it ajar and wait for about 15 minutes before removing the dishes. In this way they will

be cooler and the drying will be improved.

1. Unload the dishes.

WARNING!

• The washing cycle will not start if the dishwasher door is left open or not properly closed.
• Do not open the door when the dishwasher is working since hot water may be ejected, which could cause scalding.

Adding extra dish

A forgotten dish can be added any time before the detergent dispenser opens. If this is the case, follow the instructions below:

1. Press to pause.
2. Wait for 5 seconds then open the door.
3. Add the forgotten dishes.
4. Close the door.
5. Press The cycle will start from the point at which it was interrupted.

Changing the program in progress

A wash cycle can only be changed if it has been running for a short time otherwise, the detergent may have already been released and the dishwasher may have already drained the wash water. If this is the case, the dishwasher needs to be reset and the detergent dispenser must be refilled. To reset the dishwasher, follow the instructions below:

1. Press to switch off the dishwasher.
2. Press .again to switch on the dishwasher.
3. Repeatedly press P to select the desired washing program.
4. Press to start the program.

Child lock function

The child lock function of your dishwasher prevents accidental program changes and stops children playing with the controls while the appliance is running.

124

FR

NL

PT

EN

To activate the function, press and hold the two buttons simultaneously for more than 3 seconds. The lock indicator light will flash.

To deactivate the function, press and hold the two buttons simultaneously for more than 3 seconds. The lock indicator light will go out.

CLEANING AND MAINTENANCE

Always switch off and unplug the appliance before cleaning.
- To avoid penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind.
- Never use abrasive cleaners or scouring pads on the outer surfaces because they may scratch the finish.

Your dishwasher cleans by spraying a mixture of clean water and detergent (under pressure) against the soiled surface of dishes. The water is pumped through a rotating spray arm, drained through a filter removing food and soiled particles and pumped back through the spray arm.

Soiled water is pumped out and replaced with clean water at the end of each cycle (the number of times depends on the cycle being used).

NOTE:

Hard water conditions will adversely affect washability performance of your dishwasher.

Hard water conditions will also contribute to "Lime" (white film substance) deposits and/or "Scaling" on the stainless steel surface of the dishwasher tub and heater element located in the sump underneath the removable filter screen. To minimise these conditions, it is recommended to periodically operate/rinse the inside of the dishwasher (empty) using 1 cup of white vinegar (at least once a week).

Cleaning the door and the door seal

Clean the door seals regularly with a soft damp cloth to remove food deposits. When the dishwasher is being loaded, food and drink residues may drip onto the sides of the dishwasher door. These surfaces are outside the wash cabinet and are not accessed by water from the spray arms. Any deposits should be wiped off before the door is closed.

Cleaning the control panel

If cleaning is required, the control panel should be wiped with a soft damp cloth only.

126

FR

NL

PT

EN

Cleaning the filtering system

The filtering system in the base of the wash cabinet retains coarse debris from the washing cycle. The collected coarse debris may cause the filters to clog. Check the condition of the filters regularly and clean them if necessary under running water.

The filtering system consists of a coarse filter, a flat (Main filter) and a micro filter (fine filter).

1. Flat filter

Food and debris will be trapped by a special jet on the lower spray arm.

2. Coarse filter

Big debris, such as bone and glass that could clog the drain will be trapped in the coarse filter. To remove an item caught in this filter, gently squeeze the taps on the top of this filter and lift it out.

3. Micro filter

This filter holds soil and food residue in the sump area and prevents it from being redeposit on the dishes during a cycle.

Separate the filters and rinse all filters under running water using a soft brush. Clean the filters once a week.

Replace the flat filter and replace the filter assembly by turning them clockwise until they lock into position.

CAUTION: Never operate the dishwasher without the filters.

Cleaning the spray arms

It is necessary to clean the spray arms regularly, otherwise hard water chemicals will clog the spray arm jets and bearings.

To clean the spray arms, follow the instructions below:

To remove the upper spray arm, screw off the nut clockwise to take out the washer on the spray arm and remove the

arm.

To remove the lower spray arm, pull it out.

Wash the arms in soapy and warm water and use a soft

brush to clean the jets.

Replace them after rinsing thoroughly.

Frost precaution

Please take frost protection measures on the dishwasher in winter. Every time after washing cycles, please operate as follows:

1. Cut off the electrical power to the dishwasher at the supply source.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain the water from the inlet pipe and water valve (Use a pan to gather the water).
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.

128

FR

NL

PT

EN

After every wash

After every wash, turn off the water supply to the appliance and leave the door slightly open so that moisture and odors are not trapped inside.

No solvents or abrasive cleaning

To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Only use a cloth with warm soapy water.

To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little vinegar, or a cleaning product made specifically for dishwashers.

When not in use for a long time

It is recommend that you run a wash cycle with the dishwasher empty and then remove the plug from the mains socket, turn off the water supply and leave the door of the appliance slightly open. This will help the door seals to last longer and prevent odors from forming within the appliance.

Moving the appliance

If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be positioned on its back.

Cleaning the seals

One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring.

TROUBLESHOOTING

Before Calling For Service

Reviewing the charts on the following pages may save you from calling for service.

Problem	Possible Causes	Possible Solution
Dishwasher will not start.	Fuse blown, or the ir庚it breaker tripped	Replace fuse or reset circuit breaker. Remove any other appliance sharing the same circuit with the dishwasher.
	Power supply is not turned on.	Make sure the dishwasher is turned on and the door is closed securely. Make sure the power cord is properly plugged into the wall socket.
	Water pressure is low.	Check that the water supply is connected properly and the water is turned on.
Water not pumped from dishwasher	Kink in drain hose	Check drain hose.
	Filter clogged	Check the filters (see "Cleaning the Filtering System").
	Kitchen sink clogged	Check kitchen sink to make sure it is draining well. If kitchen sink is not draining, you may ask a plumber to check it.
Suds in the tub	Improper detergent	Use only the detergent special for dishwasher to avoid suds. If this occurs, open the door and let the suds evaporate. Add 1 gallon of cold water to the bottom of the dishwasher. Close the dishwasher door, then select any cycle. Initially, the dishwasher will drain out the water. Open the door after draining stage is complete and check if the suds have disappeared. Repeat if necessary.
	Spilled rinse aid	Always wipe up rinse aid spills immediately.
Stained tub interior	Detergent with colourant may be used.	Make sure that the detergent has no colourant.
White film on inside surface	Hard water minerals.	To clean the interior, use a damp sponge with dishwasher detergent and wear rubber gloves. Never use any other cleaner than dishwasher detergent otherwise it may cause foaming or suds.
There are rust stains on cutlery.	The affected items are not corrosion resistant.	Avoid washing items that are not corrosion resistant in the dishwasher.
	A program is not run after adding dishwasher salt. Traces of salt have gotten into the wash cycle.	Always run a wash program without any crockery after adding salt.
	The cap of the salt container is loose.	Check the cap is secure.

130

FR

NL

PT

EN

The dishwasher is noisy.	Dishes are rattling against each other. The spray arms are knocking against the dishes.	Refer to "Loading the Dishwasher" to rearrange the dishes.
The dishes are not clean.	The dishes have not been arranged properly.	Refer to "Loading the Dishwasher".
	The washing program selected is too gentle.	Select a more intensive program. Refer to "Washing Programs".
	Not enough detergent has been used or it is unsuitable.	Use more detergent or change the detergent.
	The spray arms are clogged.	Rearrange the items so that the spray arms can rotate freely.
	The filters are not clean or not in the correct position.	Clean and/or position the filters correctly.
Cloudiness on glassware	Combination of soft water and too much detergent	Use less detergent if you have soft water and select a shorter cycle to wash the glassware and to get them clean.
White spots appear on dishes and glasses	Hard water area can cause limescale deposits.	Add more detergent.
The dishes are not quite dry.	Improper loading	Refer to "Loading the Dishwasher".
	The rinse aid has run out or too little is being used.	Increase or refill the amount of rinse aid.
	Wrong program has been selected.	Choose a program with long washing time.
Dishwasher leaks.	Overfill dispenser or rinse aid spills.	Be careful not to overfill the rinse aid dispenser. Spilled rinse aid could cause oversudsing and lead to overflowing. Wipe away any spills with a damp cloth.
	Dishwasher is no level.	Make sure the dishwasher is level.
Drain pump doesn't stop.	Overflow	The system is designed to detect an overflow. When it works, it shuts off the circulation pump and turns on the drain pump.
Yellow or brown film on inside surfaces	Tea or coffee stains	Using a solution of 1/2 cup of bleach and 3 cups of warm water to remove the stains by hand. WARNING: You have to wait for 20 minutes after a cycle to let the heating elements cool down before cleaning interior; otherwise, burns will happen.
	Iron deposits in water can cause an overall film.	You have to call a water softener company for a special filter.
The detergent dispenser cover cannot be closed properly.	Clogged detergent residue is blocking the catch.	Clean the detergent from the catch.
Detergent left in dispenser cups.	Dishes block detergent cups.	Re-loading the dishes properly.
Steam	Normal phenomenon	There is some steam coming through the vent by the door latch during drying and water draining.
Black or gray marks on dishes	Aluminum utensils have rubbed against dishes.	Use a mild abrasive cleaner to eliminate those marks.
Water standing on the bottom of the tub	This is normal.	A small amount of clean water around the outlet on the tub bottom keeps the water seal lubricated.

FR

NL

PT

EN

131

Error codes

When some malfunctions happen, the appliance will display error codes to warn you.

Codes	Meanings	Possible Causes
E1	Door open	The door is opened when the dishwasher is operating.
E2	Water inlet	Water inlet malfunctions.
E3	Water drainage	Water drainage malfunctions
E4	Temperature sensor	Temperature sensor malfunction.
E5	Overflow/leakage	Overflow occurs/Water leakage occurs.
E6	Water leakage	Water leakage occurs
E7	Heating element	Abnormal heating occurs.

WARNING!

If overflow occurs, turn off the main water supply before calling a service. If there is water in the base pan because of an overfill or small leak, the water should be removed before restarting the dishwasher.

PRODUCT INFORMATION SHEET

COMMISSION DELEGATED REGULATION (EU) 2019/2017 with regard to energy labelling of household dishwashers

Supplier's name or trade mark: Etablissements Darty & fils © | Proline

Supplier's address: 9 Rue des Bateaux-Lavoirs, 94200 Ivry-sur-Seine, France

Model identifier: SDW4910WH2, SDW4910SL2

General product parameters:

Parameter	Value	Parameter		Value
Rated capacity (a) (ps)	9	Dimensions in cm	Height	84
			Width	45
			Depth	60
EEI (a)	55,9	Energy efficiency class (a)		E
Cleaning performance index (a)	1,130	Drying performance index (a)		1,090
Energy consumption in kWh [per cycle], based on the eco programme using cold water fill. Actual energyconsumption will depend on how the appliance is used.	0,704	Water consumption in litres [per cycle], based on the eco programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.		10,0
Programme duration (a) (h:min)	4:00	Type		free-standing
Airborne acoustical noise emissions (a) (dB(A) re 1 pW)	47	Airborne acoustical noise emission class (a)		C
Off-mode (w) (if applicable)	0,49	Standby mode (w) (if applicable)		0,60
Delay start (w) (if applicable)	1,00	Networked standby (w) (if applicable)		N/A

Minimum duration of the guarantee offered by the supplier: 24 months

Additional information:

Weblink to the supplier's website, where the information in point 6 of Annex II to Commission Regulation (EU) 2019/2022 is found: www.darty.com

(a) for the eco programme.

To find the model information in the product database:

Click the link

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675166

https://eprel.ec.europa.eu/screen/product/dishwashers2019/1675167

Rated voltage / frequency	220-240V ~ 50Hz
Rated power	1850W
Water pressure	0,04 - 1,00 MPa

FR

NL

PT

EN

133

REPAIR AND SPARE PARTS SERVICE

Do not disassemble or repair the appliance by yourself. Failure to do so may result in an electric shock or personal injury.

To access to professional repair and order spare parts, please get the support from FNAC DARTY after-sales service.

Spare parts for your appliances will be delivered within 15 working days after having received the order.

Please Note!

All appliances have a 2-year warranty.

Warranty does not cover damages caused due to improper installation, unauthorized modification, self-repair or non-professional repair.

Contact us at :

DARTY

www.darty.com

0978 970 970

24 Hours

7 Days a week

129 Avenue Gallieni, 93140 Bondy,

France

Vanden Borre

in alle vertrouwen

www.vandenborre.be

023340000

8AM-6PM

Mon to Sat

Slesbroekstraat 101

1600 Sint-Pieters-Leeuw

Belgium

DISPOSAL

As a responsible retailer we care about the environment. As such we urge you to follow the correct disposal procedure for the appliance and packaging materials. This will help conserve natural resources and ensure that it is recycled in a manner that protects health and the environment.

You must dispose of this appliance and its packaging according to local laws and regulations.

Because this appliance contains electronic components, the appliance and its accessories must be disposed of separately from household waste when the appliance reaches its end of life.

Contact your local authority to learn about disposal and recycling.

The appliance should be taken to your local collection point for recycling. Some collection points accept appliance free of charge.

We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product improvement and development.

EU Declaration of Conformity

Product Description:

The object of the declaration described above is in conformity with the relevant Union

harmonisation legislation:

Low Voltage Directive (LVD)

Eco design requirements for energy-related products (ErP)

RoHS

EMC:

EN IEC 55014-1:2021

EN IEC 55014-2:2021

EN IEC 61000-3-2:2019+A1

EN 61000-3-3:2013+A1

CISPR 14-1:2020

CISPR 14-2:2020

IEC 61000-3-2:2018+A1:2020

IEC 61000-3-3:2013+A1:2017+A2:2021

LVD:

EN 60335-1:2012+A11+A13+A1+A14+A2+A15

EN 60335-2-5: 2015+A11+A1

EN 62233:2008

ErP :

(EU) 2019/2017

(EU) 2019/2022

(EU) 2021/340

(EU) 2021/341

EN 60436:2020+A11:2020+A12:2022

This declaration of conformity is drawn up under the sole responsibility of the manufacturer.

The person responsible for this declaration is:

Place, Date / Lieu :