ELIOSAN1530 - Kitchen extractor FALMEC - Free user manual and instructions
Find the device manual for free ELIOSAN1530 FALMEC in PDF.
| Product type | Kitchen extractor (hood) |
| Brand | FALMEC |
| Model | ELIOSAN1530 |
| Operating mode | External exhaust (extracting) or recirculation (filtering) |
| Number of speeds | 4 (speed 4 timed) |
| Control | Electronic with buttons and indicator LEDs |
| Lighting | High-efficiency LED spots |
| Timer | Automatic shut-off after 15 minutes |
| Filter alarm | Fixed red LED after 30 hours of use |
| Anti-grease metal filters | Hand washable or dishwasher safe (max 55°C) |
| Activated carbon filters | Replacement recommended every 3-4 months |
| Minimum distance above a gas hob | 65 cm (can be reduced according to the hob manual) |
| Power supply | 230 V ~ 50 Hz (typical) |
| Earth connection | Mandatory |
| Installation | Reserved for qualified personnel |
| Surface maintenance | Clean with a soft cloth and neutral detergent every 15 days |
| Safety | Do not use if cable damaged, do not modify the appliance |
Frequently Asked Questions - ELIOSAN1530 FALMEC
User questions about ELIOSAN1530 FALMEC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Kitchen extractor in PDF format for free! Find your manual ELIOSAN1530 - FALMEC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ELIOSAN1530 by FALMEC.
USER MANUAL ELIOSAN1530 FALMEC
Installation operations are to be carried out by skilled and qualified installers in accordance with the instructions in this booklet and in compliance with the regulations in force.
DO NOT use the hood if the power supply cable or other components are damaged: disconnect the hood from the electrical power supply and contact the Dealer or an authorised Servicing Dealer for repairs.
Do not modify the electrical, mechanical or functional structure of the equipment.
Do not personally try to carry out repairs or replacements. Interventions carried out by incompetent and unauthorised persons can cause serious damage to the unit or physical and personal harm, not covered by the Manufacturer's warranty.
WARNING FOR THE INSTALLER
TECHNICAL SAFETY
Before installing the hood, check the integrity and function of each part. Should anomalies be noted, do not proceed with installation and contact the Dealer.
Do NOT install the hood if an aesthetic (or cosmetic) defect has been detected. Put it back into its original package and contact the dealer.
No claim can be made for aesthetic (or cosmetic) defects once it has been installed.
During installation, always use personal protective equipment (e.g.: Safety shoes) and adopt prudent and proper conduct.
The installation kit (screws and plugs) supplied with the hood is only to be used on masonry walls: in case of installation on walls of a different material, assess other installation options keeping in mind the type of wall surface and the weight of the hood (indicated on page 2).
Keep in mind that installations with different types of fastening systems from those supplied, or which are not compliant, can cause electrical and mechanical seal danger.
Do not install the hood outdoors and do not expose it to atmospheric elements (rain, wind, etc.).
ELECTRICAL SAFETY
The electrical system to which the hood is to be connected must be in accordance with local standards and supplied with earthed connection in compliance with safety regulations in the country of use. It must also comply with European standards regarding radio antistatic properties.
Before installing the hood, check that the electrical mains power supply corresponds with what is reported on the identification plate located inside the hood.
The socket used to connect the installed equipment to the electrical power supply must be within reach: otherwise, install a mains switch to disconnect the hood when required.
Any changes to the electrical system must be carried out by a qualified electrician.
The maximum length of the flue fastening screws (supplied by the manufacturer) must be 13 mm. Use of non-compliant screws with these instructions can lead to danger of an electrical nature.
Do not try to solve the problem yourself in the event of equipment malfunction, but contact the Dealer or an authorised Servicing Department for repairs.
When installing the hood, disconnect the equipment by removing the plug or switching off the main switch.
FUMES DISCHARGE SAFETY
Do not connect the equipment to discharge pipes of fumes produced from combustion (for example boilers, fireplaces, etc.).
Before installing the hood, ensure that all standards in force regarding discharge of air out of the room have been complied with.
USER WARNINGS
These warnings have been drawn up for your personal safety and those of others. You are therefore kindly asked to read the booklet carefully in its entirety before using or cleaning the equipment.
The Manufacturer declines all responsibility for any damage caused directly, or indirectly, to persons, things and pets as a consequence of failing to comply with the safety warnings indicated in this booklet.
It is imperative that this instructions booklet is kept together with the equipment for any future consultation.
If the equipment is sold or transferred to another person, make sure that the booklet is also supplied so that the new user can be made aware of the hood's operation and relative warnings.
After the stainless steel hood has been installed, it will need to be cleaned to remove any residues remaining from the protection adhesive as well as any grease and oil stains which, if not removed, can cause irreversible damage to the hood surface. To properly clean the unit, the manufacturer recommends using the supplied moist wipes, which are also available sold separately.
Insist on original spare parts.
INTENDED USE
The equipment is solely intended to be used to extract fumes generated from cooking food in non-professional domestic kitchens: any other use is improper. Improper use can cause damage to persons, things, pets and exempts the Manufacturer from any liability.
The equipment can be used by children over the age of 8 and by persons with reduced physical, sensory and mental abilities, or with no experience or knowledge, as long as they do so under supervision or after having received relative instructions regarding safe use of the equipment and understanding of the dangers connected to it.
Children are not to play with the equipment. Cleaning and maintenance by the user must not be carried out by children without supervision.
USE AND CLEANING WARNINGS
Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching off the main switch.
Do not use the hood with wet hands or bare feet.
Always check that all electrical parts (lights, extractor fan) are off when the equipment is not being used.
The maximum overall weight of any objects placed or hung (if applicable) on the hood must not exceed 1.5 kg.
Always supervise the cooking process during the use of deep-fryers: Overheated oil can catch fire.
Do not leave open, unattended flames under the hood.
Do not prepare food over an open flame under the hood.
Never use the hood without the metal anti-grease filters: in this case, grease and dirt will deposit in the equipment and compromise its operation.
Accessible parts of the hood can be hot when used at the same time as the cooking appliances.
Do not carry out any cleaning operations when parts of the hood are still hot.
There can be a risk of fire if cleaning is not carried out according to the instructions and products indicated in this booklet.
Disconnect the main switch when the equipment is not used for long periods of time.
If other appliances that use gas or other fuels are being used at the same time (boiler, stove, fireplaces, etc.), make sure the room where the fumes are discharged is well-ventilated, in compliance with the local regulations.
INSTALLATION
Only intended for qualified personnel.
Before installing the hood, carefully read the chapter 'SAFETY INSTRUCTIONS AND WARNINGS'.
TECHNICAL FEATURES
The technical specifications are exhibited on the labels located inside the hood.
POSITIONING
The minimum distance between the highest part of the cooking equipment and the lowest part of the hood is indicated in the installation instructions.
Generally, when the hood is placed over gas cookers, the distance must be at least 65 cm (25.6"). However, according to an interpretation of standard EN60335-2-31 dated 11-07-2002 of TC61 (sub-clause 7.12.1 meeting 15 agenda item 10.11), the minimum distance between the cooker and lower part of the hood can be reduced to the quota reported in the installation instructions.
Should the instructions for the gas cooker specify a greater distance, this must be taken into consideration.
Do not install the hood outdoors and do not expose it to outdoor environment (rain, wind, etc.).
Disconnect the equipment from electrical mains power supply before carrying out any operations on the hood.
Ensure that the wires inside the hood are not disconnected or cut: in the event of damage, contact your nearest Servicing Department.
Refer to qualified personnel for electrical connections.
Connection must be carried out in compliance with the provisions of law in force.
Before connecting the hood to the electrical mains power supply, check that:
- voltage supply corresponds with what is reported on the data plate located inside the hood;
- the electrical system is compliant and can withstand the load (see the technical specifications located inside the hood);
- the power supply plug and cable do not come into contact with temperatures exceeding 70°C;
- the power supply system is effectively and properly connected to earth in compliance with regulations in force; the socket used to connect the hood is within reach.
In case of:
- devices fitted with cables without a plug: the type of plug to use is a "standardised" one. The wires must be connected as follows: yellow-green for earthing, blue for neutral and brown for the phase. The plug must be connected to an adequate safety socket.
- fixed equipment not provided with a power supply cable and plug, or any other device that ensures disconnection from the electrical mains, with an opening gap of the contacts that enables total disconnection in overvoltage category III conditions. Said disconnection devices must be provided in the mains power supply in compliance with installation regulations.
The yellow/green earth cable must not be cut off by the switch.
The Manufacturer declines all responsibility for failure to comply with the safety regulations.
FUMES DISCHARGE
EXTERNAL EXHAUST HOOD (SUCTION)
In this version, the fumes and vapors are discharged outside through the exhaust pipe.
To this end, the hood outlet fitting must be connected via a pipe to an external output.
The outlet pipe must have:
- a diameter not less than that of the hood fitting.
- a slight downward slope (drop) in the horizontal sections to prevent condensation from flowing back into the motor, and the minimum required number of bends.
- the minimum required length to avoid vibrations and reduce the suction performance of the hood.
You are required to insulate the pipes if they pass through cold environments.
In the presence of motors with 800 m³/h or higher, a check valve is present to prevent external air from flowing back.
Deviation for Germany:
When the kitchen hood is used at the same time as appliances that are powered by energy other than electricity, the negative pressure in the room must not exceed 4 Pa (4 x 10⁻⁵ bar).
HOOD WITH INTERNAL RECIRCULATION (FILTERING)
In this model, the air passes through the charcoal filters to be purified and recycled in the environment.
Ensure that the active carbon filters are assembled into the hood; if not, install them as indicated in the assembly instructions.
In this version the check valve must not be assembled: remove it if it is on the air outlet fitting of the motor.
ASSEMBLY INSTRUCTIONS
only intended for qualified personnel
The hood can be installed in various configurations.
The generic assembly steps apply to all installations; for each case, follow the specific steps provided for the required installation.
OPERATION
WHEN TO TURN ON THE HOOD?
Switch on the hood at least one minute before starting to cook to direct fumes and vapours towards the suction surface.
WHICH SPEED IS TO BE SELECTED?
1st speed: maintains the circulation of clean air with low electricity consumption. 2nd speed: normal conditions of use. 3rd speed: presence of strong odours and vapours. 4th speed: rapid disposal of odours and vapours. (ONLY 800m3 /h)
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The metal filters must be cleaned every 30 hours of operation.
For further details refer to the "MAINTENANCE" section.
USE OF SLIDER
LIGHT SWITCH
0
By placing the slider in position 0, the hood light is off
1
By placing the slider in position 1, the hood light is on
MOTOR SWITCH
0
By placing the slider in position 0, the hood motor is off
1
By placing the slider in position 1, the hood motor is set at minimum speed
2
By placing the slider in position 2, the motor is set at medium speed
3
By placing the slider in position 3, the motor is set at high speed
The motor activation is signalled by the switching on of the red LED on the slider
800
m³/h
ELECTRONIC PUSHBUTTON PANEL
Motor ON/OFF
Upon start-up, the speed is that stored at the previous operation.
Increase speed from 1 to 4
Speed 4 is only active for a few minutes, then speed 3 activates.
The speeds are indicated by the LEDs on the keys:
Speed 1
Speed 2
Speed 3
Speed 4
Reduce speed from 4 to 1
Light on/off
TIMER (red LED flashing)
Auto switch-off after 15 min.
The function deactivates (red LED off) if:
- The TIMER key is pressed again.
- The ON/OFF key (●) is pressed.
FILTER ALARM (red LED steady on with ● off)
Anti-grease filter maintenance after approximately 30 hours of operation.
Press the meter for 3 seconds to reset.
MAINTENANCE
Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching off the main switch. Do not use detergents containing abrasive, acidic or corrosive substances or abrasive cloths.
Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the metal anti-grease filters: frequent cleaning of the filters and their supports ensures that no flammable grease is accumulated.
CLEANING OF EXTERNAL SURFACES
You are advised to clean the external surfaces of the hood at least once every 15 days to prevent oily substances and grease from sticking to them. To clean the brushed stainless steel hood, the Manufacturer recommends using "Magic Steel" wipes.
Alternatively and for all the other types of surfaces, it can be cleaned using a damp cloth, slightly moistened with mild, liquid detergent or denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths.
Do not use too much moisture or water around the push button control panel and lighting devices in order to prevent humidity from reaching electronic parts.
The glass panels can only be cleaned with specific, non-corrosive or non-abrasive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these instructions.
CLEANING OF INTERNAL SURFACES
Do not clean electrical parts, or parts related to the motor inside the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal filters (at least once a month) leaving them to soak in boiling water and cleaning solution for 1 hour, taking care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the filter material to darken: to reduce the possibility of this problem from happening, use low-temperature washes (55°C max.).
To extract and insert the metal anti-grease filters see the assembly instructions.
ACTIVE CARBON FILTERS
These filters retain the odours in the air that pass through them. The purified air is recirculated into the environment.
The active carbon filters must be replaced on average every 3-4 months under normal conditions of use.
See assembly instructions to replace the active carbon filters.
LIGHTING
The range hood is equipped with high efficiency, low consumption LED spotlights with an extremely long life-span under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in the figure.
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out trash or refuse bin symbol on the appliance means that the product is WEEE, i.e. "Waste electrical and electronic equipment", accordingly it must not be disposed of with regular unsorted waste (i.e. with "mixed household waste"), but it must be disposed of separately so that it can undergo specific processing for its re-use, or a specific treatment, to remove and safely dispose of any substances that may be harmful to the environment and remove the raw materials that can be recycled. Proper disposal of these products contributes to saving valuable resources and avoid potential negative effects on personal health and the environment, which may be caused by inappropriate disposal of waste.
ic processing for its re-use, or a specific treatment, to remove and safely dispose of any substances that may be harmful to the environment and remove the raw materials that can be recycled. Proper disposal of these products contributes to saving valuable resources and avoids potential negative effects on personal health and the environment, which may be caused by inappropriate disposal of waste.
You are kindly asked to contact your local authorities for further information regarding the designated waste collection points nearest to you. Penalties for improper disposal of such waste can be applied in compliance with national regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented differently in each country. Accordingly, if you wish to dispose of this appliance, we suggest contacting your local authorities or dealer to find out the correct method of disposal.
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish to dispose of this appliance in other countries, we suggest contacting your local authorities or dealer to find out what the correct method of disposal is.
The Manufacturer reserves the right to make changes to the equipment at any time and without prior notice. Printing, translation and reproduction, even partial, of this manual are bound by the Manufacturer's authorisation.
The Manufacturer reserves the right to make changes to the equipment at any time and without prior notice. Printing, translation and reproduction, even partial, of this manual are bound by the Manufacturer's authorisation.
Technical information, graphic representations and specifications in this manual are for information purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for any transcription or translation errors.
ACTIVE CARBON FILTERS
SAFETY TECHNICAL PRECAUTIONS
Installation must be carried out by qualified and experienced installers in accordance with the instructions in this manual and current regulations.
If the power supply cable is damaged, do not use the appliance: disconnect it from the power supply and contact the distributor or an authorized technical support center for repair.
Do not make electrical, mechanical or functional modifications to the appliance.
Do not attempt to replace parts or repair the appliance yourself. Work performed by unqualified or unauthorized personnel may cause harm, including serious injury, and voids the manufacturer's warranty.
PRECAUTIONS FOR THE INSTALLER
SAFETY TECHNICAL
Before starting installation of the hood, check that all its parts are intact. If damage is found, do not proceed with installation and contact the distributor.
If external defects are found, do not install the hood; place it in its original packaging and contact the distributor.
After installation, no claims will be accepted for external defects.
During installation, always use personal protective equipment (e.g., protective footwear) and proceed with caution and care.
The fixing kit supplied with the hood (screws, plugs) can only be used for brick or concrete walls. For installation on walls made of other materials, use appropriate fixings suitable for the wall strength and the weight of the hood (indicated on page 2).
Installation and use of the hood with the use of fastening systems other than those specified may lead to a dangerous situation of an electrical or mechanical nature.
Do not install the hood outdoors or in places where it would be exposed to atmospheric agents (rain, wind, etc.).
Electrical safety
The electrical system to which the hood is connected must comply with current regulations and must be grounded in accordance with the regulations in force in the country of use; it must also comply with European standards regarding radio interference devices.
Make sure that the voltage in the electrical system corresponds to the value indicated on the rating plate located inside the hood.
The socket used to connect the hood to the electrical power supply must be accessible after installation. Otherwise, it is necessary to provide an accessible switch to disconnect the hood in case of need.
Any modifications to the electrical system must be carried out only by a qualified electrician.
The maximum length of the screws for fixing the hood (supplied by the installer) is 13 mm. Use of screws not conforming to these instructions may lead to a dangerous situation of an electrical nature.
In case of malfunction of the fuse, do not attempt to repair it yourself; contact the manufacturer or an authorized technical service center for repair.
During installation of the hood, disconnect the appliance from the power socket using the main switch.
Safety of smoke exhaust
Do not connect the appliance to smoke ducts for the evacuation of fumes produced by combustion (boilers, fireplaces, etc.).
Before installation, make sure that all requirements of current regulations regarding air exhaust outside the premises are met.
Safety measures for the user
These safety measures are intended for your safety and for the safety of others, so please read them carefully before using or cleaning the appliance.
The manufacturer is not responsible for any direct or indirect damage to people, property, or domestic animals caused by failure to follow the instructions given in this manual.
It is important that this manual with instructions is kept together with the equipment for future reference.
In case of resale or transfer of the appliance to another person, make sure that the manual is also handed over so that the new owner can familiarize themselves with the operation of the hood and the corresponding safety precautions.
After installing the hood made of stainless steel, it is necessary to remove any residues of the protective coating. Possible stains of grease or oil may remain. If they are not removed, they may permanently damage the surface of the hood. For this operation, the manufacturer recommends using the cloths supplied, which are also available for sale.
Required spare parts.
INTENDED USE
The appliance is intended exclusively for extracting fumes generated during cooking in domestic environments, not for professional use. Any other use, different from that described, is considered improper and may cause damage to people, property, or domestic animals. The manufacturer declines all liability.
The appliance can be used by children aged at least 8 years, and by persons with reduced physical, sensory, or mental capabilities, or lacking experience and knowledge, provided they are supervised or have received instructions on the safe use of the appliance and understand the associated dangers. Children must not play with the appliance. Cleaning and maintenance performed by the user must not be carried out by children without supervision.
SAFETY PRECAUTIONS FOR OPERATION
Before performing any operation on the hood or maintenance, disconnect the appliance from the electrical supply by unplugging it or switching off the main switch.
Do not touch the hood with wet hands and do not use it barefoot.
When the appliance is not in use, always check that all electrical components (light, aspirator) are switched off.
The total weight of objects placed on or hung from the hood (where provided) must not exceed 1.5 kg.
Watch the appliance during use: hot oil may catch fire.
Do not light an open flame under the hood.
He opened the hood and pulled it out.
He did not use the hood without metal chloride filters; in this case, the filter must be inserted into the device, which may affect its operation.
The accessible parts of the hood may heat up when used with gas appliances.
Do not touch the hood while its parts are still hot.
If cleaning is not carried out in accordance with the methods and using the means specified in this instruction, there is a risk of fire.
When the hood is not used for a long period of time, it is necessary to turn off the main switch.
In case of simultaneous use of other devices (boiler, stove, fireplace, etc.) operating on gas or other fuel, provide appropriate ventilation of the room where smoke is extracted, in accordance with current regulatory requirements.
INSTALLATION
This section is intended only for qualified personnel.
Before starting to install the hood, you should carefully read the section "SAFETY TECHNIQUES AND PRECAUTIONARY MEASURES".
TECHNICAL CHARACTERISTICS
The technical data of the appliance are given on the labels located inside the hood.
POSITIONING
The minimum distance between the highest part of the appliance and the lowest part of the hood is indicated in the installation instructions.
Usually, when the hood is installed above a gas cooking surface, this distance should be no less than 65 cm (25.6"), but no less, based on the requirements of EN60335-2-31 of 11-07-2002 of TC61 (subclause 7.12.1, note 15 of the notification of 10.11), the minimum distance between the cooking surface and the lower part of the hood can be reduced according to the instructions given in the installation instructions.
If the manual for the hood indicates a greater distance, this must be taken into account. Install the non-return valve in places where it would be exposed to atmospheric agents (rain, wind, etc.).
ELECTRICAL CONNECTION
(section intended for qualified personnel only)
Before performing any operation, disconnect the appliance from the power supply.
Check that there are no detached or damaged wires inside the hood: if so, contact the nearest Technical Support Service.
The electrical connection must be made by qualified personnel.
The connection must be made in compliance with the requirements of current legislation.
Before connecting the hood to the electrical network, check that:
The voltage in the electrical network corresponds to that indicated on the rating plate located inside the hood; - The electrical network meets the requirements of current standards and can withstand the load (see technical specifications inside the hood); The plug and electrical cable must not come into contact with temperatures above 70°C; The electrical system is equipped with an effective earth connection in accordance with current standards; The socket used for connection is accessible after installation of the hood.
In case:
The device must be connected using a standardized plug. The connection must be made with a plug that is suitable for the socket. The plug must be connected to a suitable socket. - FIXING THE DEVICE TO THE CABINET WITH THE SOCKET. The socket must be connected to the mains supply, ensuring complete disconnection from the live contacts, ensuring full disconnection in conditions of overvoltage category III.
These disconnecting devices must be provided in the electrical network in accordance with installation rules.
The earth wire must not be disconnected by the switch.
The manufacturer accepts no liability in the event of failure to comply with safety rules.
OUTPUTS
Exhaust hood with external discharge (suction type)
In this version, the air is discharged outside through an air duct.
For this purpose, the exhaust outlet must be connected by means of a pipe to the external air inlet.
The exhaust pipe must have
- Diameter not less than the diameter of the exhaust outlet. Slope downwards (fall) of horizontal sections to prevent condensate from entering the engine. Minimum number of necessary bends.
Minimum possible length to avoid vibration and reduction of suction capacity.
It is necessary to insulate the pipe if it passes through cold rooms.
To prevent air from returning from outside, a non-return valve is installed, which is required for engines with a power of 800 m³/h or more.
Deviations from the diagram:
When the room is simultaneously equipped with a chimney and appliances operating on gas other than electric, the negative pressure inside the room must not exceed 4 Pa (4x10-5 bar).
Exhaust hood with internal recirculation (filtering)
The air is drawn in, passes through an activated carbon filter, and is then returned to the room.
Make sure that the activated carbon filters are installed in the hood; otherwise, install them as described in the installation instructions.
The hood must be installed. Check if it is installed on the air inlet pipe of the engine.
Installation instructions
pa3dien npedha3hauen TOIbko KBaIIHmIpuOBaHHOMy nepcoHaJIy
BbTAAKMyO HObYctAHabNtBbTaBpa3nnHbIX KOHpyrauaJx. 06Ie 3TaNbMoTHaKa DeCTBnTeNBbI DnR BCEX TNOB yCTa npIepKnBaTc TaKke OTrEbnHO yKa3aHbIX 3TaNOB, COOTBe TNYy cTAHOBNk.
ФУНКЦИОНИРОВАНИЕ
КОГДА ВКЛЮЧАТЬ ВЫТЯЖКУ?
Вытяжку следует включать хотя бы за минуту до начала приготовления пищи для образования потока воздуха для направления дыма и пара к всасывающей поверхности.
КАКУЮ СКОРОСТЬ ВЫБИРАТЬ?
I скорость: поверхность чистая, воздух при низком потреблении электроэнергии.
II скорость: нормальные условия использования.
III скорость: сильные запахи и пары.
IV скорость: быстрое удаление запахов и паров (800 м³/ч).
КОГДА МЫТЬ ИЛИ ЗАМЕНЯТЬ ФИЛЬТРЫ?
Металлические фильтры следует мыть после каждых 30 часов использования.
Более подробно см. главу "ТЕХОБСЛУЖИВАНИЕ".
ИСПОЛЬЗОВАНИЕ СЕЛЕКТОРОВ
СЕЛЕКТОР ОСВЕЩЕНИЯ
0
By position 0, lighting is off.
1
By position 1, lighting is on.
ENGINE SELECTOR
0
By position 0, the engine is off.
1
By position 1, the engine runs at minimum speed.
2
By position 2, the engine runs at medium speed.
3
By position 3, the engine runs at maximum speed.
Engine start is signaled by the indicator on the selector.
ELECTRONIC KEYPAD
The set speed corresponds to the speed entered on the display at the previous switch-off.
Increase speed from 1 to 4
Speed 4 works only for a few minutes, then switches to speed 3.
Decrease speed from 4 to 1
The LED buttons show the speed:
Speed 1
Speed 2
Speed 3
Speed 4
Light on/off
Timer (red LED indicator)
Automatic switch-off after 15 minutes.
(Red LED indicator when off)
Cleaning of the grease filters is recommended approximately every 30 hours of operation. Press (2/3) and hold for 3 seconds to reset the counter.
Before performing any maintenance operation, disconnect the appliance from the mains using the main switch or unplug it from the socket.
Do not use cleaning agents containing abrasives,
acids, or corrosive substances, nor cloths with hard surfaces.
Regular maintenance guarantees proper functioning and efficiency.
Pay special attention to metal filters or grids, as regular cleaning of the filters guarantees the absence of easily flammable grease deposits.
CLEANING OF EXTERNAL SURFACES
It is recommended to clean the external surface of the hood at least every 15 days to prevent the accumulation of oil or grease deposits. For cleaning the hood made of painted stainless steel, it is recommended to use "Magic Steel" products.
As an alternative, and also for all other surfaces of the hood, it is possible to use a damp cloth moistened with neutral liquid detergent or denatured alcohol.
Finish cleaning with a thorough rinse and dry with a soft cloth.
Do not use too much water near the control panel or lighting devices to avoid moisture getting onto the electronic parts.
Cleaning of glass panels is carried out only with the use of special non-corrosive or non-abrasive cleaning agents and a soft cloth.
The manufacturer is not responsible for failure to comply with these instructions.
CLEANING OF INTERNAL SURFACES
It is forbidden to clean electrical components or parts of the motor inside the hood using liquids or solvents.
Cleaning of internal metal parts is described in the previous paragraph.
METAL GREASE FILTERS
It is recommended to wash the metal filters (at least once a month) by soaking them for about 1 hour in hot water with detergent, then rinsing thoroughly and drying before reinstalling.
Do not use corrosive, acidic, or abrasive cleaning agents.
Rinse thoroughly and let them dry completely before reinstalling them in place.
The filters may discolor over time, but this does not affect their performance. To reduce this, use gentle cleaning programs with a maximum temperature of 55°C.
Removal and installation of metal grease filters are described in the installation instructions.
ACTIVATED CARBON FILTERS
These filters retain impurities present in the air passing through them. The purified air is then returned to the room.
The activated carbon filter must be replaced with a new one on average every 3-4 months under normal usage intensity.
Instructions for replacing the activated carbon filter are given in the installation manual.
LIGHTING
The hood is equipped with high-efficiency LED lighting elements with low energy consumption and a long service life under normal operating conditions.
If it is necessary to replace the light bulb, proceed as shown in the figure.
DISPOSAL AT END OF SERVICE LIFE
The symbol of the crossed-out waste bin indicates that this product belongs to the category of WEEE. That is, "waste from electrical and electronic equipment", therefore it cannot be thrown away together with unsorted waste (i.e., with "household waste"), but must be disposed of separately, so that the necessary recycling operations can be carried out, or for special treatment to safely neutralize possible harmful materials for the environment and recover raw materials that can be reused. Proper disposal of this product will help save natural resources and avoid potentially negative effects on human health and the environment, which may result from improper disposal.
We ask you to contact local authorities for more detailed information on recycling. In accordance with national legislation, penalties may be imposed in case of improper disposal of these wastes.
INFORMATION ON DISPOSAL IN EU COUNTRIES
INFORMATION ON DISPOSAL IN COUNTRIES OUTSIDE THE EU
The symbol of the crossed-out waste bin is valid only in EU countries. If you wish to dispose of this appliance in other countries, we recommend contacting local authorities or the distributor for information on proper disposal.
ATTENTION!
The manufacturer reserves the right to make changes to the product at any time without prior notice. The text, translation and reproduction, including partial, of this manual are possible only after obtaining prior written permission from the manufacturer.
Technical information, graphic representations and illustrations contained in this manual are indicative and not binding.
The manual was written in Italian; the manufacturer is not responsible for possible errors or mistakes in the translation.
TECHNICAL SPECIFICATIONS
- WARNING FOR THE INSTALLER
- TECHNICAL SAFETY
- ELECTRICAL SAFETY
- FUMES DISCHARGE SAFETY
- USER WARNINGS
- INTENDED USE
- USE AND CLEANING WARNINGS
- INSTALLATION
- TECHNICAL FEATURES
- POSITIONING
- FUMES DISCHARGE
- EXTERNAL EXHAUST HOOD (SUCTION)
- HOOD WITH INTERNAL RECIRCULATION (FILTERING)
- ASSEMBLY INSTRUCTIONS
- OPERATION
- USE OF SLIDER
- LIGHT SWITCH
- MOTOR SWITCH
- ELECTRONIC PUSHBUTTON PANEL
- MAINTENANCE
- CLEANING OF EXTERNAL SURFACES
- CLEANING OF INTERNAL SURFACES
- METAL ANTI-GREASE FILTERS
- ACTIVE CARBON FILTERS
- LIGHTING
- DISPOSAL AFTER END OF USEFUL LIFE
- INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
- INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
- THE MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES TO THE EQUIPMENT AT ANY TIME AND WITHOUT PRIOR NOTICE. PRINTING, TRANSLATION AND REPRODUCTION, EVEN PARTIAL, OF THIS MANUAL ARE BOUND BY THE MANUFACTURER'S AUTHORISATION
- SAFETY TECHNICAL PRECAUTIONS
- PRECAUTIONS FOR THE INSTALLER
- SAFETY TECHNICAL
- SAFETY OF SMOKE EXHAUST
- SAFETY MEASURES FOR THE USER
- SAFETY PRECAUTIONS FOR OPERATION
- TECHNICAL CHARACTERISTICS
- ELECTRICAL CONNECTION
- IN CASE
- OUTPUTS
- EXHAUST HOOD WITH EXTERNAL DISCHARGE (SUCTION TYPE)
- DEVIATIONS FROM THE DIAGRAM
- EXHAUST HOOD WITH INTERNAL RECIRCULATION (FILTERING)
- INSTALLATION INSTRUCTIONS
- ФУНКЦИОНИРОВАНИЕ
- КОГДА ВКЛЮЧАТЬ ВЫТЯЖКУ
- КАКУЮ СКОРОСТЬ ВЫБИРАТЬ
- КОГДА МЫТЬ ИЛИ ЗАМЕНЯТЬ ФИЛЬТРЫ
- ИСПОЛЬЗОВАНИЕ СЕЛЕКТОРОВ
- СЕЛЕКТОР ОСВЕЩЕНИЯ
- ENGINE SELECTOR
- ELECTRONIC KEYPAD
- INCREASE SPEED FROM 1 TO
- DECREASE SPEED FROM 4 TO
- LIGHT ON/OFF
- METAL GREASE FILTERS
- ACTIVATED CARBON FILTERS
- DISPOSAL AT END OF SERVICE LIFE
- INFORMATION ON DISPOSAL IN COUNTRIES OUTSIDE THE EU
- THE SYMBOL OF THE CROSSED-OUT WASTE BIN IS VALID ONLY IN EU COUNTRIES. IF YOU WISH TO DISPOSE OF THIS APPLIANCE IN OTHER COUNTRIES, WE RECOMMEND CONTACTING LOCAL AUTHORITIES OR THE DISTRIBUTOR FOR INFORMATION ON PROPER DISPOSAL
- THE MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES TO THE PRODUCT AT ANY TIME WITHOUT PRIOR NOTICE. THE TEXT, TRANSLATION AND REPRODUCTION, INCLUDING PARTIAL, OF THIS MANUAL ARE POSSIBLE ONLY AFTER OBTAINING PRIOR WRITTEN PERMISSION FROM THE MANUFACTURER
- TECHNICAL SPECIFICATIONS
Brand : FALMEC
Model : ELIOSAN1530
Category : Kitchen extractor