CGIH3047VF - Electric stove FRIGIDAIRE - Free user manual and instructions

USER MANUAL CGIH3047VF FRIGIDAIRE

PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. United States FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followed exactly, a fire or electrical shock may result causing property damage, personal injury or death. Tip Over Hazard

• A child or adult can tip the range and be killed.
• Verify the anti-tip device has been installed to floor or wall.
• Ensure the anti-tip device is re-engaged to floor or wall when the range is moved.
• Do not operate the range without the anti-tip device in place and engaged.
• Failure to follow these instructions can result in death or serious burns to children and adults. Important Notes to the Installer:
• Read all instructions contained in these installation instructions before installing range.
• Remove all packing material from the oven compartments before connecting the gas & electrical supply to the range.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer. Important Notes to the Consumer: Keep these instructions with your owner’s guide for future reference.

Range leveling leg As when using any appliance generating heat, there are certain safety precautions you should follow. These are listed in the Use & Care Guide, read it carefully. Be sure your range is installed and grounded properly by a qualified installer or service technician. Make sure the wall coverings around the range can withstand the heat generated by the range. To eliminate the need to reach over the surface elements, cabinet storage space above the elements should be avoided. Anti-tip bracket To check if the anti-tip bracket is installed properly, use both arms to grasp the rear edge of the range back. Carefully attempt to tilt range forward. When properly installed, the range should not tilt forward. Refer to the anti-tip bracket installation instructions supplied with your range for proper installation. P/N 809127104 (1903) Rev. CEnglish – pages 1-6 Français – pages 7-12

1. Clearances and Dimensions

a. Provide adequate clearances between the range and adjacent combustible surfaces. b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. Front view Side view Typical cabinet installation 29 7/8" 30” Minimum

Minimum to wall on either side of range above 36” height. 30” Minimum* 18” Minimum to cabinets on either side of range 13” Maximum depth for cabinets above range top. 25” Max. 36 5/8" ± 1/4" Maximum 36” SIDE VIEW FRONT VIEW Fig. 1 Minimum to wall on either side of (25 mm) range above 36’’ (914 mm) height. 30” Minimum 0” clearance below cooking top and at rear of range 30” 30” (762 mm) (762 mm) Minimum 18” (457 mm) Minimum to cabinets on either side of range. 13” 330 mm Maximum depth for cabinets above range top. *30" (762 mm) MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM 25” OF AN UNPROTECTED WOOD OR METAL CABINET;635 36”24" (610 mm) MINIMUM WHEN BOTTOM OF WOOD OR (914 mm) METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" (6 mm) FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" (0.4 mm) STAINLESS30”STEEL, 0.024" (0.6 mm) ALUMINUM 0” (0 mm) clearance below cooking top and at rear of range. OR 0.020" (0.5 mm) 0" (0 mm) CLEARANCE IS (762COPPER. mm) THE MINIMUM FOR THE REAR OF THE25-RANGE. FOLLOW 3/4” RANGE 30” (654 mm) ALL DIMENSION REQUIREMENTS PROVIDED ABOVE (762 mm) OVERALL DIMENSIONS

HAZARD, AND INCORRECT COUNTERTOP AND CABINET

CUTS. 26 6/8" Centerline of range Doo 47" r op

Fig. 2 BACK VIEW All dimensions for electrical outlet location are maximum. Dashed cubed area shows where the electrical outlet must be installed for flush to the wall installation. 11” (279 mm) 22” (559 mm)

Maximum (759 mm) THE CABINETS. Door Open Wall Edge 2-5/8” (67 mm) for models equipped with warmer drawers 3-1/2” (89 mm) for models equipped with storage drawers

2. Tools You Will Need

installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template. For leveling legs and Anti-Tip Bracket:

• Adjustable wrench or channel lock pliers
• 5/16" Nutdriver or Flat Head Screwdriver
• Electric Drill & 1/8" Diameter Drill Bit (Masonry Drill Bit if installing in concrete)
• Level & Measuring Tape For electrical supply connection:
• 1/4" & 3/8" Socket driver or Nutdriver Additional Materials You Will Need:
• Power Supply Cord or
• Copper Electrical Wiring & Metal Conduit (for hard wiring) B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8” (3 mm) pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20° downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 5/32” (4 mm) pilot hole 1-3/4” (44 mm) deep. The screws provided may be used in wood or concrete material. Use a 5/16” (8 mm) nutdriver or flat head screwdriver to secure the bracket in place.

3. Anti-Tip Bracket Installation

Instructions Important Safety Warning To reduce the risk of tipping of the range, the range should be secured to the floor by properly installed anti-tip bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself. (32 mm) If range is ever moved to a different location, the anti-tip brackets must also be moved and installed with the range. Instructions are provided for installation in wood or cement fastened to either the floor or wall. When installed to the wall, make sure that screws completely penetrate dry wall and are secured in wood or metal. When fastening to the floor or wall, be sure that screws do not penetrate electrical wiring or plumbing. Fig. 4 (32 mm) A. Locate the Bracket Using the Template - (Bracket may be located on either the left or right side of the range. Use the information below to locate the bracket if template is not available). Mark the floor or wall where left or right side of the range will be located. If rear of range is against the wall or no further than 1-1/4" (32 mm) from wall when installed, you may use the wall or floor mount method. If molding is installed and does not allow the bracket to fit flush against the wall, remove molding or mount bracket to the floor. For wall mount, locate the bracket by placing the back edge of the template against the rear wall and the side edge of template on the mark made referencing the side of the range. Place bracket on top of template and mark location of the screw holes in wall. If rear of range is further than 1-1/4" (32 mm) from the wall when Fig. 5

C. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. Note: A minimum clearance of 1/8” (3 mm) is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide range back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer. For models with a warmer drawer or broiler compartment, grasp the top rear edge of the range and carefully attempt to tilt it forward. Power supply cord with 4-prong grounding plug 240V grounded wall receptacle Fig. 7 It is the personal responsibilty of the consumer to have the appropiate outlet with the correct, properly grounded wall receptacle installed by a qualified electrician.

5. Model and Serial Number

Location The serial plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or the lower panel area. (17 mm) Fig. 6 When ordering parts for or making inquires about your range, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your range.

4. Electrical Connection

Requirements Your serial plate also tells you the Kilowatt rating (power requirements) and Voltage ratings. Avoid fire hazard or electrical shock. Failure to follow this warning may cause serious injury, fire, or death. Serial Plate Locations: Plug the range power cable (4 conductors) into a 4 conductor range outlet. Outlet must be properly grounded and in accordance with the Canadian Electrical Code (CSA Standard (C22.1 Part 1 -- latest edition) -- and any local electrical code requirements. Locate outlet 6" (152 mm) above the floor in the wall behind the range. Serial plate is located on the lower right front frame of the appliance. Alternate location may be under cooktop. Fig. 8 Grounding Instructions For personal safety, this appliance must be properly grounded. For maximum safety, the power cord must be plugged into an electrical outlet that is correct voltage, is correctly polarized and properly grounded in accordance with local codes.

7. Door Handle Mounting Instructions (some models)

Note: Installation of the filler trim kit is not required. Disconnect electrical power to range before beginning installation. Before servicing any part of the appliance, make sure the appliance is off and the surfaces are cool. Attempting to service the appliance while hot may cause burns or other injury.

1. Remove handles from carton and any other protective

2. Position handle end caps over left and right preinstalled shoulder bolts (A) that are fastened to the

door, ensuring the holes for the set screws are facing down.

3. While holding handle firmly against door, loosely tighten

right Allen set screw (B) with supplied Allen wrench until there is no gap between handle and door.

4. Still holding the handle firmly to the door, firmly tighten left

Allen set screw (B) with supplied Allen wrench.

5. Return to the right Allen set screw (B) and firmly tighten with

supplied Allen wrench. Filler Trim Attachment Instructions:

1. Remove the 7 screws on the vent trim on the back.

2. Place the filler trim over the back by lining up the 7

screw holes of the filler trim with the vent trim and tighten screws. All set screws should be tightened so the screw is below the surface of the handle. The handle should be drawn tight to the door with no gaps. The door handle may loosen over time or if it was installed improperly. If this happens, tighten the set screws on the handles. Fig. 10

3. When filler trim is secured it will be flush with the top of

the range. Fig. 11 Fig. 12 - Range with filler trim installed.

8. Care, Cleaning and

Maintenance Before You Call for Service Read the "Before You Call" and operating instruction sections in your Use & Care Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Refer to the Use & Care Manual for cleaning instructions. If removing the range is necessary for cleaning or maintenance, disconnect the electrical power supply. If the electrical supply is inaccessible, lift the unit slightly at the front and pull out away from the wall. Pull only as far as necessary to disconnect the electrical supply. Finish removing the unit for servicing and cleaning. Reinstall in reverse order making sure to level the range and check electrical connections. See pages 2 and 3 for proper anchoring instructions. Refer to the warranty in your Use & Care Manual for our toll-free service number and address. Please call or write if you have inquiries about your range product and/or need to order parts. Some models have a cool-air intake vent on the rear of the appliance. Do not block or obstruct this vent. Fig. 13