CTL55E - Industrial vacuum cleaner FESTOOL - Free user manual and instructions

Product type	Mobile industrial vacuum cleaner class L
Brand	Festool
Model	CTL 55 E
Tank capacity	55 litres
Power consumption	350 - 1200 W
Max. connected power (tool socket)	2400 W (CE), 1100 W (CH/DK), 1800/500 W (GB), 1200 W (AUS)
Max. airflow rate	228 m³/h
Max. vacuum pressure	23000 Pa
Filter surface area	14000 cm²
Suction hose	Ø 27 mm x 3.5 m
Sound pressure level	72 dB(A) according to EN 60704-2-1
Mains cable length	7.5 m
Protection degree	IP X4
Dimensions (L x W x H)	710 x 380 x 935 mm
Weight	22 kg
Main functions	Dry dust and liquid suction, automatic start via power tool or pneumatic tool, suction power adjustment, antistatic system, thermal protection, blow function
Maintenance and cleaning	Regular filter cleaning by shaking (handle), filter bag and filter element replacement, tank draining, decontamination after use with hazardous dusts
Safety	Automatic shut-off in case of overheating, liquid level indicator, IP X4 water splash protection, emergency stop via switch
Spare parts and repairability	Festool accessories available (filter bags, filter elements, antistatic hoses, pneumatic module, etc.), maintenance and repair by a Festool authorized workshop, annual technical inspection recommended
General information	Compliant use for class L hazardous dusts (concentration ≤ 1 mg/m³), water suction possible, 24-month EU warranty, recycling according to regulations

Frequently Asked Questions - CTL55E FESTOOL

How to change the filter bag of the Festool CTL 55 E?

Open the vacuum cleaner by unlocking the closing clips and tilt the upper part upwards. Remove the used bag following the markings, dispose of it according to applicable regulations. Carefully clean the tank and the turbine area with a damp cloth. Insert a new filter bag (ref. 452973) by pressing the sleeve firmly onto the suction inlet. Close the vacuum cleaner.

How to use automatic start (AUTO mode)?

Set the on/off switch to the 'Auto' position. Plug the power tool into the integrated socket of the vacuum cleaner. The suction motor starts automatically as soon as the tool is switched on. Make sure the tool is turned off before turning the switch to 'Auto'.

What to do in case of vacuum cleaner overheating?

The vacuum cleaner is equipped with thermal protection that stops it before reaching a critical temperature. Turn off the device and let it cool down for about 5 minutes. If restarting fails after this time, contact a Festool authorized service workshop.

Can I vacuum water with the CTL 55 E?

Yes, the vacuum cleaner is suitable for vacuuming water. Before vacuuming liquids, remove the filter bag. Preferably use a special liquid filter. A level indicator (2.12) automatically stops suction when the tank is full. Caution: never vacuum flammable liquids such as gasoline or paint thinner.

How to clean the filter element?

Cleaning the filter element is only necessary when using without a filter bag. Actuate the cleaning handle (2.1) about 10 times back and forth. This shakes the element to loosen dust. For a deeper clean, follow the filter element replacement instructions (ref. 452923).

Which accessories are recommended for vacuuming hazardous dusts?

Use exclusively Festool accessories, especially an antistatic hose to avoid electrostatic discharges. For automatic start with pneumatic tools, install the pneumatic module (ref. 452829) and the VE power supply unit (ref. 452797). Wear a P2 respirator during maintenance operations.

How to empty the collection tank?

Unplug the vacuum cleaner. Open the closing clips, tilt the upper part upwards, then remove it horizontally forward after releasing the support. Empty the tank and clean it. To reassemble, insert the two pins of the upper part into the recesses (1.5) and close the clips.

What is the protection class of the vacuum cleaner?

The vacuum cleaner has protection class IP X4, meaning it is protected against water splashes from all directions. It must be connected to a grounded power outlet to ensure electrical safety and the operation of the antistatic system.

How to attach a Systainer on top of the vacuum cleaner?

The top panel (1.9) is designed to hold a Systainer. Use the two closures (1.11) to secure it firmly. You can also store tools and accessories on the panel and in the side compartments (1.6). A hose holder (1.10) can be installed in the opening (1.7).

What to do if the vacuum cleaner does not start after an overload?

Check if the thermal protection has tripped: wait 5 minutes for cooling. If the problem persists, check the power cord, socket, and fuse. If the device remains inoperative, contact a Festool service workshop. Never open the motor cover yourself, this must be done by an authorized professional.

USER MANUAL CTL55E FESTOOL

Head of Research, Development and Technical Documentation

Technical data Mobile dust extractors
Power consumption		350 - 1200 W
Connected load to appliance plug socket max.:	EU	2400 W
	CH, DK	1100 W
	GB 240 V/ 110 V	1800 W/ 500 W
	AUS	1200 W
Volume flow (air) max., turbine		228 m³/h
Vacuum max., turbine		23000 Pa
Filter surface		14000 cm²
Suction hose		Ø 27 mm x 3,5 m
Sound pressure level in compliance with EN 60704-2-1		72 dB(A)
Power cable length		7,5 m
Protection type		IP X4
Container capacity	CTL 44 E/CTL 44 LE	44 l
	CTL 55 E	55 l
Dimensions L x W x H	CTL 44 E/CTL 44 LE	710 x 380 x 935 mm
	CTL 55 E	710 x 380 x 935 mm
Weight	CTL 44 E/CTL 44 LE	20 kg
	CTL 55 E	22 kg

The specified illustrations can be found at the beginning of the operating instructions.

Pictograms

Note, Danger!

Manual, read the instructions.

Warning: The appliance contains dust hazardous to health.

1 Intended use

The vacuum cleaners are designed as specified for the aspiration and evacuation of noxious dusts industrial threshold limit values (LTL-values) up to 1mg / m^3 corresponding to dust class 'L' in accordance with IEC 60335-2-69. The vacuum cleaner is designed as specified for extracting water. The vacuum cleaner is designed in accordance with EN 60335-1 and EN 60335-2-69 for a higher loading in industrial use.

2 Safety instructions

• Only use original Festool accessories.

• Warning: The appliance contains dust hazardous to health. Emptying and maintenance operations,

including removal of the dust collection means, must only be carried out by authorised personnel wearing suitable personal protection. Do not operate without the full filtration system fitted.

• The machine is not intended for use by persons (including children) with limited physical, sensory or mental ability or without sufficient experience and/or knowledge, unless they are supervised by a person responsible for their safety or have been instructed on how to use the machine. Children should always be supervised to ensure that they do not play with the machine.
• The appliance may be operated only in an adequately ventilated space (in compliance with national industrial safety provisions).
• Do not suck in any sparks or hot chippings.
• With the exception of wood dust, do not suck in any flammable or explosive dusts such as magnesium, aluminium etc. - Risk of explosion!
• Do not use to extract flammable or explosive liquids (e.g. petrol, thinners) - Risk of explosion!
• Do not use to extract aggressive liquids/dry materials (e.g. acids, alkalis, solvents).
• This mobile dust extractor is suitable for extracting paint dust.

• Remove plug from mains socket when not in use and before maintenance work.

• Do not pull plug out of mains socket by its cable.

• Protect the cable against heat, oil and sharp edges.
• Check the plugs and cables regularly and have them replaced by an expert if damaged.
• Do not leave devices out in the rain.
• Do not lift or carry the devices by their handles using a crane hook or lifting gear.
• The device may only be used by persons who have been trained in its use and who are authorised to do so.
• If noxious dusts have been extracted, the vacuum cleaner and all accessories must be completely cleaned (inside and outside) by suction and wiping, before removal from the contaminated area. Parts that cannot be completely cleaned are to be packed for transport in a plastic bag with an airtight seal.
• For safety reasons, only operate the machine using a totally earthed socket.

3 Appliance preparation and initial operation

The accessories are delivered horizontal in the container (2.10), and must be removed prior to initial operation.

3.1 Power supply

The line voltage and frequency must correspond with the data on the ratings plate!

Make sure that the vacuum cleaner is switched off when you plug the power cable in.

The antistatic system (AS)

Friction in the suction hose causes electrostatic charges which can result in unpleasant electric shocks for the operator. In order to conduct these static charges to earth, the extraction units are provided with an antistatic system as a standard feature. However, antistatic hoses and accessories have to be used in this case. The antistatic function will only work if the plug is plugged into a totally earthed socket.

3.2 On/off switch (1.3)

In position 0 the vacuum cleaner is switched off and the appliance plug socket (1.2) is dead.

Two modes of operation are possible:

a) Switch position „MAN“

The appliance plug socket is dead.

The cleaner motor starts immediately.

b) Switch position „Auto“

The appliance plug socket is live.

Before turning the switch to the „Auto“ position, ensure that the tool connected to the appliance plug socket is switched off.

The cleaner motor starts only when the tool connected to the appliance plug socket is switched on.

3.3 Suction force regulator (1.4)

The suction force regulator can be used to vary the suction capacity. This permits a precise adaptation to different substances to be picked up.

3.4 Temperature control

A temperature fuse switches the dust extractor off before this reaches a critical temperature to protect against overheating - switch dust extractor off and leave for around 5 minutes to cool down.

If the dust extractor still cannot be switched back on, please consult a Festool-service centre.

3.5 Connecting an electric tool

Observe the maximum connected load on the appliance plug socket (see "Technical Data")!

Make sure that the electric tool is switched off when plugging it in and unplugging it.

Connect the electric tool to the appliance plug socket (1.2).

3.6 Connecting pneumatic tools

Make sure that the pneumatic tool is switched off when plugging it in and unplugging it.

When the compressed-air module (1.8) (452829; supplied ready with CTL 44 LE) is fitted, the automatic cut-in of the appliance also operates in conjunction with compressed-air tools. We also recommend fitting of the VE supply unit (452797). The supply unit filters and oils the compressed air and allows the air pressure to be regulated. An IAS connecting piece (454757) is available for connecting Festool compressed-air tools with the IAS system. To ensure trouble-free functioning of the automatic cut-in, the operating pressure of the tool must be 6 bar.

4 Operation

4.1 Opening/closing the vacuum cleaner

• Open retaining clamps (2.2),
• Raise upper part (2.4) until support catch (2.5) engages.

Follow the reverse order to close the appliance. You must raise the upper part slightly before depressing or disengaging the support.

4.2 Changing the filter

During the following procedure, take care not to raise dust more than is unavoidable.

Wear a P2 breathing protection mask with health-hazardous dusts!

a) Changing the filter bag (3.4)

Order no.:

CTL 44 E/CTL 44 LE 452972

CTL55E 452973

• Open the vacuum cleaner,
• Remove the used filter bag (see printed text on filter bag),
• Dispose of the used filter bag in accordance with statutory requirements,
• Thoroughly clean the dirt container (2.10) and the space (3.1) for suction turbine (wipe down with a damp cloth),
• Insert new filter bag (see printed text on filter bag). Important: Press the filter bag sleeve (3.3) firmly onto the dust extraction fitting (3.2)!
• Close the vacuum cleaner.

b) Changing the filter element (2.3)

Order no.: 452923

Do not operate machine without a filter element. This may damage the motor.

• Open the vacuum cleaner,
• Remove the used filter element (see printed text on the filter element packaging),
• Dispose of the used filter element in a sealed, dust-tight bag in accordance with statutory requirements,
• Thoroughly clean dirt container (2.10) and space (3.1) for the suction turbine (wipe down with a damp cloth),
• Fit a new filter element (see printed text on the filter element packaging),
• Close vacuum cleaner.

4.3 Cleaning the filter element

To clean, move the handle (2.1) to and fro about 10 times. N.B.: You need to clean the filter element only if you use the vacuum cleaner without a filter bag.

4.4 Emptying the dirt trap (2.10)

Always remove the upper part of the vacuum cleaner before emptying the dirt container!

• Open the vacuum cleaner,
• Raise the upper part slightly, depress the support (2.5),

• Raise the upper part to the stop (vertical position),

• Remove the upper part by moving it forwards horizontally,

• Empty the dirt container,
• Replace the upper part. Warning: Make sure that both upper-part pins are fully inserted in the recesses (1.5)!
• Close the vacuum cleaner.

4.5 Stand/Brake

The wheels can be blocked by the brakes [2.8], thus preventing the vacuum cleaner from rolling away unexpectedly.

4.6 Hose depot (partly in scope of delivery)

Securing the hose depot on the dust extractor: see Fig. 4. When work is complete, you can guide the extractor hose through the opening (4.1) and deposit the hose in the depot. Similarly, the mains cable can also be guided through the opening (4.2) and deposited in the hose depot.

5 Application

• A systainer can be fixed to the storage area (1.9) with the two clamps (1.11). Tools or accessories can also be stowed on the storage area and in the storage compartments (1.6).
• A hose coupling (1.10) (487072) can be plugged into the opening (1.7). The suction hose is connected to the tool from above with the hose coupling. Alternatively, a hose clip (452998) can be fitted for coiling the suction hose.
• The push handle (2.11) (452921) makes the vacuum cleaner easier to move. Accessories (e.g. vacuum accessories) can be fixed to the push handle batten (2.9).
• An air blast is obtained by inserting a suction hose in the blast opening (2.7).

5.1 Vacuuming dry materials

A filter bag must be used without exception when evacuating noxious substances!

Before using the vacuum cleaner to evacuate dry substances, a filter bag must always be inserted in the container. Then the evacuated material can be disposed of easily. The filter element becomes damp after evacuating liquids. A damp filter element suffers more wear and tear if it is used for dry materials. Accordingly, the filter element should be dried or replaced with a dry one before dry operation.

5.2 Vacuuming liquids

Do not evacuate combustible liquids!

If foam or liquid escapes, stop work immediately and empty the dirt container.

The filter bag has to be removed before evacuating liquids. We recommend use of a special wet filter. When the maximum filling level is reached, a bag-full indicator (2.12) automatically interrupts extraction.

6 After finishing work

• Switch off the cleaner and pull the Plug of the mains lead out of the Plug socket.
• Wind up the mains lead [2.6].
• Empty dirt tank.
• Clean the vacuum cleaner inside and outside by suction and wiping.
• Deposit the appliance in a dry room, safe from unauthorised use.

7 Maintenance and care

Always remove the power supply plug from the socket before carrying out any work on the machine.

All maintenance and repair work which requires the motor casing to be opened may only be carried out by an authorised service centre.

A safety test is to be carried out at least once a year by the manufacturer or an instructed person, e.g. for possible damage to the filter and leaks in the appliance, and to ensure that the control devices are functioning.

If the user services the appliance, it must be dismantled, cleaned and serviced, as far as possible without any danger to the maintenance staff and other persons. Appropriate measures include decontamination before dismantling, locally filtered forced ventilation on the dismantling site, cleaning the service area, and suitable personal safety equipment.

8 Accessories, filter

The accessory and filter order number can be found in your Festool catalogue or on the Internet under "www.festool.com".

9 Disposal

Do not throw the power tool in your household waste! Dispose of machines, accessories and packaging at an environmentally responsible recycling centre. Observe the valid national regulations.

10 Warranty

For our tools, we give warranty for material and production defects in accordance with the locally applicable legal provisions, but in any case for at least 12 months. Within the EU member states, the warranty period is 24 months (verification through invoice or delivery note). Damage caused by, in particular, natural wear, overloading, incorrect handling, or damage caused by the operator, or damage caused through use of the equipment contrary that specified in the Operating Instructions, or damage which was known at the time of purchase, is not covered by the warranty. Furthermore, damage caused by the use of non-original accessories and consumable materials (e.g. sanding pads) is also excluded. Complaints can only be recognised if the tool is returned while still assembled to the supplier or an authorised Festool Customer Service workshop. Keep the Operating Instructions, Safety Instructions, Spare Parts List and purchase receipt in a safe place. Otherwise the respective, current warranty conditions of the manufacturer shall apply.

Note

Due to continuous research and development work, we reserve the right to make changes to the technical content of this documentation.

REACH for Festool products, their accessories and consumables

REACH is a European Chemical Directive that came into effect in 2007. As "downstream users" and product manufacturers, we are aware of our duty to provide our customers with information. We have set up the following website to keep you updated with all the latest news and provide you with information on all the materials used in our existing products: www.festool.com/reach

8 Accessoires, filter

Pn PooCoeHHeHH N OToCoeHHeHH PHeBMOnHCTpyMeHT DoJIKeH 6bITb BblKJIouyeH.

Ecnu yctahOBlen nHeBMOmOyIb (1.8) (452829, CTL 44 LE - BxOJNT B O6bEM NoCTaBKn), To 6ydet pa6oTaTb ABTomAtnKa BkJIoueHn IblJeYdaJIaHO Ue Ro aIIapata B CoUeTAHN C NHeBMOHcTpymEn TAm. PekomeHnyem YcTaHOBtB DOnOIHNteIbHo y3eI NOrTOBKn CxAToRBO3Dyxa VE (452797). DaHbI y3eI NOrTOBKn CxAToRBO3Dyxa OUn- uaeTeero, npomacInBaET IIO3BOJAErpeylnpoBAHne DaBLeHn BO3Dyxa. IJa npincoeiHnHn IHeBMOHcTpymEtOB Festool c cnCTeMoI IAS y HAc Imeetc coeHNtIb IAS (454757). IJa oBecepeHn 6e3ynpueHno pa60tbl ABtomKn BkIoUeHn pa6Ouee daBLeHn IHcTpymEnta DoJXHO 6bITb paBHO 66ap.

4 Pnucn DeiCTBna

4.1 OTKpbITb/3aKpbITb nbIeYda-JraUoHn annapaT

• pa30mKHyTb 3aOpHbIe 3aIeJkn (2.2),
• OTKINHyTb BBepx BePxHIOu qAcTb aannapata (2.4) Do 3actoOpnbAHnO npobI (2.5).

3aKpbBaTb B o6paTHOM nopJKe.ДЯ npIXKaTna IJI paCzepnIeHnO onOpbl Tpe6yEtc cHaJaIa CJIerka npINOdHrB BepXHIOU qAcTb nbIeYdaJIaIooIero aannapata.

4.2 3aMeHaΦnJIbTpTa

Pn BbIIOJIHeHn CJIeDyUOuX pa6oT CJIeIITb 3a TeM, UTo6bI He pacIbJIaJaCb Nblb.

Ecn n nbIb coepKnt BpeHbIe npImecn, noIb30BaTbcra pecnnpaTopom D2!

a) CmeHa MeuKa- nblnc6OpHnka (3.4)

N° 3aKa3a:

CTL 44 E/CTL 44 LE 452972

CTL55E 452973

-OTKpbITb nbIeYdaJIoUoN annapaT
- BbIHyTb IcNoJIb3OBAHHbI ΦnJIbTp-MeWOK (cM. yKa3aHHe Na ΦnJIbTp-MeWKe),
- yTnIu3npoBaTb nCNoJb3OBAHHbI ΦnJIbTpMeUOK cOrJaCHO npEynCMOTpeHbIM HopMaM,
- NOIHOCTbIO OUHCTNTb rpr3eYIOBHTeJIb (2.10) I NOIocTb (3.1) IJRA Tpy6nHbI OTCOca (npoTepeTB BIAJHOI TpIKNO),
- BINOJNTb HOBbI ΦINbTp-MeWOk (cM. yKa3aHne Ha ΦINbTp-MeWke). BaxKHo: KpeNko HaNabVTb

Mуфту Фильту-Мeшka (3.3) на BCасьВаюшништуцер (3.2)!
- 3aKpbItb nbIeUdaJauoJn annpapaT.

b) CmeHaΦnIbTpkyoUeTo ΘIeMeHtA (2.3)

N°3aKa3a: 452923

3a npeuaetcBbTjKka 6e3 nJbTpOBaJIbHOro 3JeMeHa! 3To MoKeT npNBecTu K nobpejdeHIO 3JeKtpoDbuRaTeIa.

• OTKpbITb nbIeuydajouo nn annapaT,
  -ИЗВЛЕЧь ИСПОЛБ30ВАнHBи ΦИЛБТРОВАЛБНИ マЛЕМЕNT (сM.УКAZAHп Ha yPаКOBКe ΦИЛБТРОВАЛБНOrO эЛemeHTa),
• yTnIu3nPoBaTb NcNoJb30BaHhbI ΦNtPoBaJIbHbI ΘJeMeHT, BLOXNB eRO B NblJeHeIpOnHucaeMbI 3aKpbITbI NaKeT, cOrJaCHo ppeDycmOTpeHbIM HOpMaM,
• NOIHOCTbIO OUHCTnTB rpa3eYIOBNTeJIb (2.10) I NOLOCTb (3.1) dIy Typ6uHbI OTCocA (npoTepeTb BlaJXHO TpIKnO),
  -yCTaHOBNTb HOBbI ΦnJIbTpOBAJIbHbI ΘJIeMeHT (cM. yKa3aHHe Ha yPaKOBKe ΦnJIbTpOBAJIbHOrO ΘJIeMeHTa),
• 3aKpbItb nbIeUdJaIouoN annapaT.

4.3 OuNCTKaФиЛьТpoВаьHOrO 3JIeMeHTeA

Дя оистк pyky (2.1) kaatb Bnepei-Ha3ad Ok. 10 pa3. ПрimeuaHne: oynctka ФильтpoBaJbHoro элем enta Tpe6yetc TolbkoВ TOM clyuae, ecIn nbileyuJaIauOu n annapaT pa6oTaET 6e3 Фильтmeшka.

4.4 OnopoxKHeHne nblIec6bOpHnka (2.10)

peed onopoxHeHem rpa3eyIobnteTne Tpe6yeTc
chauaLCHaTB BepxHIOU qactb nbIeYdaJIaHOeTo
annapata!

-OTKpbITb nbIleuydajlouyn annpaT,
- CJIerKa npHIOdHЯTb BepXHIOU qAcTb, npJxKaTb onopy (2.5),
- OTKINHyTb BepxHIOU yAcTb Do yNopa BBepx (Bep-TnKaJIbHoe nOLOXKeHne),
- CnTb BnepeiBepxHIOU qAcTb, yIepKINBaJ eE B Tropn30HTaJIbHOJ PLOCKOCTN,
- onopokhntb rpa3eyIobNTeJIb,
-BHObHacaIHTbBepXHIOU qactb.BHmAHHe: IoJIHoCTbIO BBeCTn 6a 6oITa BepxHeu qactn B npEHa3NaueHHbIe JIy HIX BbIeMKn (1.5)!
- 3aKpbItb NblJeUdaJIoUan nnapapT.

8 PrnHaJneKHoCTn,OnJIbTp

Homepa 3aka3a Дя пинадлжноctey n onlbtp Bbl haideTe B Baшем kaTalore Festool nInnВ INHTepHet no aDpecy „www.festool.com".

9 ytnln3aun

He BbIbpaBbIaIe aIppaT BMeCTe C bIbOBbIMn OTXoamn! OBecepeyTe 6e3OpacHyO dIy OkpyJxauSei cpebl yTIJIIN3aCNIu aIppaTa, oChAcTkN uynakobKn. CoJIIOJaTe DeIcTBYUOJIne HaCIOHaJIbHbIe npednscAHn.

10 FapaHTn

Для наших пиборов мbl пededoctabлгem rapaHTnIO,pacnpoctpaHЯоуocHa DeΦeKtbl MaTePnIaI n npO3BOdCTBa,COrlaCHO 3akOHoJaTeJIbHbIM npedncaHЯm,DeiCTBvUOuM B KOHKpeTHO CTpaHe.MHHMaJIbHbI cpoK DeiCTBnA rapaHTn12 MeCAseB.Длястpan-yuaCTnU EC cpoK DeiCTBnA rapaHTn10 MeCAseB.Длястpan-yuaCTnU EC cpoK He pacnpoctpaHЯETcHa NOBpeJdeHna,poLyueHbIe B pe3yIbTaTe eCTeTBeHNo I3Hoca/INcNoJIb-3OBaHna,nepeRpy3Kn,HeNaIeJkaUeRo INcNoJIb-3OBaHna,NOBpeJdeHna IO BInHe NOpIb3OBaTeJIa IInn pni NcNoJIb3OBaHnN BOppeKn PyKOBoDCTBy no 3KcPIyatauN,JI6o I3BeCTHbIe Ha MOMENT POKynK (yuEHaToBapa).IckJIouaetc TaKxge yUep6,Bbl3BaHbI nCNoJIb3OBaHnEm HeoprInHaJIbHoO ochTknI paCxOJNbIx MaTePnIaNob (HaNPImep,ShIIΦOBaJIbHbIX TapeLoK).

PpeTeH3nn npHHMaHTcTToIbKO B TOM Clyuae,ecnnp6op DoCTaBLeH K NoCTaBUnky nIn aBTOpN3OBaHHbI cepBnCHbI ueHTp fIpMbI Festool B Hepa3o6paHHom Bnde. CoXpaHnTe PyKobOJCTBO nO 3KcPnLyataun, INHcTpYkUnn Po TexHnke6e3OnaChocTn I TOBaHbI ueK. B ocTaJIbHOM dei

CTBOBaTb COrIaCHO COOTBeTcTBUOuM yCIOBnA M IpeIoCTaBJIeHn rapaHTn n3rOToBnteJI.

PpimmeuHne

B cBra3n C nocTo8HHbIMN nccJIeOBAHn8Mn HOBbIMn TexHnueckmN pa3pa60TkamN 6npMa oCTaBJIaET 3a co6oI npABo Ha BHeceHne I3MeHeHn BTexHnueckne xapakTepeNCTIKN.

REACH pour n3deI'Festool, nx ochakn npacxOndbIX MaTePnaIob

C 2007 roda dinpekTbBa REACHЯВЯETcpe rIaMeHToM IO XIMnueckm BeIeCTBam, DeIcTByUOuM HaTeppntopnn BceI EBpOnbl. BbIcTypaR B poNl «PnBVeKaeMoTO yUacTHNKa» 3TOro peIaMeHTa, Mbl, KAK IpnON3BOINTEJI N3deJIIn, PpIHUMaEM Ha Ce68O63aTeJIbCTBO IpeIOCTABJrT b COOTBeTCTBYUOuYIOHΦOpMaZNU O HsIM KJIeHTaM. YTo6bl DEpxKaTbBAC B Kypce IocLeDNHX Co6blTNI INpeIOCTABJrTbHΦOpMaZNU O BeIeCTBax, KOToPbIE BKJIQUeHbIBCNICOK BblSeYNOMJHyTORO peIaMeHTa N KOToPbIEMOrYT NcNoJIb3OBaTbCS B HaXNX N3deJIuX, Mbl C03-DAJI N CpeZnaJIbHbI Be6-caIT:www.festool.com/reach

3.3 Regulator sity ssania (1.4)