R30 R40 - Flashlight SEAC - Free user manual and instructions

Product type	Rechargeable LED dive torch
Model	SEAC R30 / R40
Maximum depth rating	100 m (both models)
LED power	R30: 15 W (3 x 5 W); R40: 20 W
Luminous flux (Hi/Low/Flashing)	R30: 1500/450/1500 lm; R40: 2300/730/2300 lm
Lux at 1 m	R30: 20500; R40: 25400
Color temperature	5700-7300 K
LED type	R30: Cree XP-G2; R40: 3x Cree XPL
Number of LEDs	3
Adjustable beam angle	12° to 75°
Beam distance	R30: 285 m; R40: 310 m
Battery type	R30: Rechargeable Li-ion 26650 3.7V 5000mAh; R40: Rechargeable Li-ion 26800 3.7V 5400mAh
Recommended charger	USB adapter, 5V 1-2A
Burn time (Hi/Low)	R30: 2h / 5h; R40: 1.5h / 4h
Weight in air	R30: 470 g; R40: 594 g
Length	R30: 167 mm; R40: 206 mm
Head diameter	R30: 65 mm; R40: 62 mm
Switch	Magnetic sliding switch with Hi/Low/Flashing modes
Safety features	Safety lock ring to prevent accidental activation
Build materials	Aluminum body, tempered glass lens, aluminum reflector, NBR O-rings
Maintenance and cleaning	Rinse with fresh water after each dive; grease O-rings with silicone grease; avoid chlorine-based cleaners and solvents
Spare parts and repairability	Use original SEAC spare parts; annual service by authorized center recommended
Warranty	2 years from purchase date, excluding normal wear items (O-rings, batteries)

Frequently Asked Questions - R30 R40 SEAC

How do I install the battery correctly?

Open the aluminum cap at the end of the handle and remove the plastic charging ring. Insert the Li-ion battery with the positive pole (+) facing into the torch. Apply silicone grease to the O-rings, then screw the charging ring and aluminum cap back on clockwise. Always respect the polarity markings to avoid short circuits.

How do I recharge my SEAC torch?

Unscrew the end cap, connect a micro-USB cable to the torch port, and plug the other end into a 5V 1-2A adapter. The red LED near the port indicates charging; when it turns green, the battery is fully charged. Unplug the mains side first, then the torch. Avoid leaving it charging for more than a few hours after full charge.

Can I adjust the beam width?

Yes, the torch allows adjusting the light cone from 12° to 75° by rotating the torch head while holding the handle. Turn the head with the rubber ring in the desired direction to widen or narrow the beam.

How does the safety lock work?

The torch has a safety ring nut just below the switch. Rotate it so the pointer aligns with the closed lock icon to lock the switch and prevent accidental activation. Rotate it the other way to align with the open lock icon to enable the switch.

What is the maximum diving depth?

The SEAC R30 and R40 have a maximum depth rating of 100 meters. Do not exceed this depth.

What battery type is used in the R30?

The R30 uses a rechargeable Li-ion 26650 battery with 3.7V and 5000mAh. Use only the same type of battery for replacement.

What battery type is used in the R40?

The R40 uses a rechargeable Li-ion 26800 battery with 3.7V and 5400mAh. Always replace with the identical type.

How long does the battery last on maximum power?

On Hi mode, the R30 delivers 1500 lumens with a burn time of 2 hours; the R40 delivers 2300 lumens for about 1.5 hours. On Low mode, the R30 lasts about 5 hours and the R40 about 4 hours.

Can I use the torch outside water?

It is recommended to use the torch exclusively underwater because high temperatures can occur when used out of water. If you use it on land, avoid prolonged operation and never point it at eyes.

How should I maintain the torch after diving?

After each dive, rinse the torch with fresh water and dry it. Inspect and grease the O-rings with silicone grease whenever you open the body. Avoid cleaning with chlorine-based products or solvents, and have the torch inspected annually by an authorized SEAC center.

USER MANUAL R30 R40 SEAC

Lampada subacquea ricaricabile in Alluminio Rechargeable dive torch in aluminium Torche subaquatique rechargeable en aluminium Foco submarino recargable de aluminio Aufladbare Aluminium-Tauchlampe

Italiano....3

English....11

Français....19

Espanol 27

Deutsch 35

2

Congratulazioni

MODALITÀ DI CONTROLLO PRIMA DELL'IMMERSIONE

PICTURE A

Thanks for having chosen a technologically advanced product from SEAC.

The manufacturing processes, raw materials used, and attention to detail all make SEAC products reliable both in terms of quality and durability over time. SEAC's on-going technological expansion consistently guarantees continual innovation.

Enjoy yourself with SEAC products!

Introduction

SEAC aluminum torches are the result of advanced research in collaboration with experts in the field.

The high-light-efficiency LEDs and the reliability of this product make the SEAC torch ideal for any type of dive.

GENERAL WARNINGS

WARNING

Before using the torch, make sure you have read this manual in its entirety. WARNING! Never point the torch into your eyes or the eyes of other people, either on dry land or during the dive.

WARNING! Be sure to remove the batteries when transporting the torch by air.

WARNING! Do not leave the battery in the torch if it will be unused for a long time.

WARNING! When replacing the battery, remember to check the polarity.

WARNING! If you need to replace the battery, always use the same type of battery indicated in the manual.

• Do not keep the torch switched on out of the water for long periods.
• Never aim the light into your own eyes or those of others, either during the dive or out of the water.
• Do not remove the lens ring nut during the dive or when the torch is wet.
• Never hold the torch near sources of heat.
• Always use original spare parts when conducting any regular or supplementary maintenance.

TECHNICAL CHARACTERISTICS

	R30
Max. depth	100 m
LED power	15 W (3 x 5 W)
Lumens rating	Maximum power (Hi): 1500Low power (Low): 450Flashing: 1500
Lux at 1 m	20500
Color temperature (° Kelvin)	5700°-7300° K
LED Type	Cree XP-G2
Number of LEDs	3
Light beam	Adjustable from 12° to 75°
Depth of light beam	285 m
Type of batteries	1 X Rechargeable Li-ion 266503.7 V -5000 mAh
USB battery charger recommended	output 5 V - 2 A
Lens	Tempered glass
Reflector material	aluminum
Seals	O-ring
O-ring material	NBR
Weight in air (including batteries)	470 g
Length	167 mm
Diameter (head)	65 mm
Switch	Magnetic, sliding
Modes	Maximum power (Hi)Low power (Low)Flashing
Burn time	Hi= 2 hLow= 5 h

	R40
Max. depth	100 m
LED power	20 W
Lumens rating	Maximum power (Hi): 2300Low power (Low): 730Flashing: 2300
Lux at 1 m	25400
Color temperature (° Kelvin)	5700°-7300°
LED Type	3*XPL
Number of LEDs	3
Light beam	Adjustable from 12 to 75°
Depth of light beam	310 m
Type of batteries	1X Rechargeable Li-ion 268003.7 V -5400 mAh
USB battery charger recommended	output 5V 1 - 2A
Lens	Tempered glass
Reflector material	aluminum
Seals	O-ring
O-ring material	NBR
Weight in air (including batteries)	594 g
Length	206 mm
Diameter (head)	62 mm
Switch	Magnetic slide
Modes	Maximum power (Hi)Low power (Low)Flashing
Burn time	Hi= 1 1⁄2 h maxLow= 4 h max

ADJUSTABLE LIGHT BEAM WIDTH

The torch has a system that allows users to adjust the angle of the light cone during use from 12° to 75° by turning the head.

Grasp the handle of the torch firmly with one hand, and with the other grip the head of the torch where the special rubber ring is located. Rotate one direction or another depending on whether you want the light beam to be broader or narrower.

WARNING

During this operation, be careful to grasp the base of the torch firmly and do not touch the end cap, because unscrewing this could cause the torch to flood.

WARNING

Strictly follow the polarity markings when inserting the battery!

INSERTING THE BATTERY

• Unscrew the aluminum cap at the end of the handle, turning counterclockwise.
• Remove the plastic charging ring, turning counter-clockwise.
• Insert the battery, making sure that the positive pole (+) is pointing into the torch.
• Grease the sealing O-rings with a layer of silicone grease.
• Screw the plastic recharging ring nut back on clockwise, taking care not to damage the threading while doing so.
• Screw the aluminum terminal at the end of the handle back on, turning clockwise.

WARNING

Failure to fully tighten this cap could result in water leaking into the torch during use.

- Check that the torch switches on using the switch.

WARNING

If the battery is inserted incorrectly (inverted polarity), a short circuit will be created, causing irreversible damage and a risk that the torch could explode.

SWITCH

The torch has a sliding magnetic switch with three positions: 100% light output, low power setting (30% of maximum power), and flashing.

ENGAGING OR DISENGAGING THE SAFETY

The torch features an exclusive and effective safety system, designed to prevent the torch from switching on accidentally. To insert the safety, rotate the circular ring nut right below the switch as far as it can go. The pointer engraved into the ring nut will line up with the closed lock icon. The switch will be locked. To disengage the safety, simply turn the ring nut the other way until the pointer lines up with the open lock icon. In the position the switch is not secured and is operative.

PRE-DIVE INSPECTION

• If your torch has not been used recently, check the condition of the batteries by ensuring that it switches on.
• Check that the body is fully closed.
• As soon as you enter the water, check that no bubbles emerge from the body of the torch.

RECHARGING THE BATTERY

WARNING

Pay the utmost attention to ensuring that there are no flammable objects or products near the torch while it is charging.

• Unscrew the end cap counter-clockwise (where the strap attaches).
• Insert the micro-USB cable connector to the port on the torch and connect the other end to a 5 Volt, 1 - 2 Amp power adapter. The red LED near the micro-USB housing on the end of the torch will light up immediately. This indicates that the battery is charging. When the LED turns green, it means that the battery is fully charged. Unplug the connector plugged to the power adapter or computer USB port first, and then unplug the micro-USB connector from the torch.

WARNING

Avoid leaving the torch connected to the power once it is charged, and in any event not longer than a few hours. Failure to do so could cause damage to the product and pose a danger to people and/or things.

FLOODING

If water gets into the torch, open the body, remove the battery, and immediately rinse the internal parts in fresh water. Then dry everything with a cloth and a hair dryer using warm air, paying close attention to mechanical parts. Remove any oxide that may have formed on the metal parts and conduct an operations test.

If a significant quantity of water has entered the torch and has remained there for a long period, open the torch body and immediately rinse the internal parts in fresh water. We suggest that you immediately contact a competent repair center or contact the closest SEAC shop.

USAGE RESTRICTIONS

• The maximum operating depth is 200 m.
• Because of the high temperatures that can arise in the torch when used out of the water, we recommend that you use it exclusively underwater.

MAINTENANCE AND TRANSPORT

It is important to abide by the following instructions:

• Always transport the torch in a bag that will protect it from any blows.
• When you aren't using the torch, always make sure you have fully inserted the safety in order to prevent the torch from switching on accidentally, which could cause fires. For extended transport in the trunk or hold, it's good practice to always remove the batteries from the torch. This provision may be mandatory with certain airlines.
• Avoid prolonged exposure to the sun.
• After a dive (sea, lake, or pool), always rinse with fresh water and dry.
• Check the condition of the gaskets (O-rings) every time you open the body of the torch.
• Clean and grease the parts involved in opening the torch with silicone grease.
• Avoid cleaning the torch with products containing chlorine (sodium hypochlorite/bleach, etc.), aggressive surfactants (such as degreasers), or solvents to avoid damaging the rust protectant anodic treatment, the plastic parts, and the sealing gaskets.
• It is advisable to have your product inspected annually by an authorised SEAC center.

SEAC declines all responsibility for damage caused to the user resulting from improper use of equipment. The same is true of direct or indirect damage of any kind caused to people or things resulting from any periods of disuse of the product or incorrect use of the same.

WARRANTY CONDITIONS

SEAC guarantees the product two years from the time of purchase.

SEAC strongly recommends that you keep your sales receipt as evidence of your date of purchase.

The warranty does not include parts subject to normal wear and tear:

• O-ring
• Batteries.

This warranty does not cover damage resulting from:

• mechanical blows.
• Use in excessively chlorinated or polluted water.
• Prolonged exposure to intense sources of heat above 70 °C.
• Damage to the threads caused by screwing improperly.

The warranty will be forfeited if:

• the equipment is used improperly, failing to comply with the instructions.
• The owner makes changes to or tampers with the product, or has personally conducted repairs, or if these procedures were conducted by unauthorized personnel.

WARNING

Do not dispose of the battery or the torch in the environment at the end of its life cycle.

Dispose of the product at a special collection point.

Disposal of electrical and electronic equipment in the European Union must comply with European Union Directive 2002/967CE.

PICTURE A

The EU Declaration of Conformity is available at: www.seacsub.com

Félicitations

VÉRIFICATION AVANT LA PLONGÉE

CONDITIONS DE GARANTIE

PICTURE A

CÓMO RECARGAR LA PILA

ADVERTENCIA

PICTURE A

PICTURE A