ALASKA - Strollers HAUCK - Free user manual and instructions

USER MANUAL ALASKA HAUCK

Read these instructions carefully before use and keep them safe. If you do not follow these instructions, your child's safety can be impaired.

• This pram is meant for 1 child from 0 months upwards, weighing up to 15 kg . The maximum load on this pram may not exceed 15 kg .
  WARNING: Do not leave your child unsupervised.
  WARNING: Keep plastic packaging materials out of the reach of children in order to avoid a risk of suffocation.
  WARNING: Before use, make certain that all locking positions are closed.
  WARNING: Use a safety belt as soon as your child can sit up on his/ her own.
  WARNING: Always use the crotch belt in combination with the pelvis belt.
  WARNING: the seat position is unsuitable for children under 6 months.
  WARNING: Any loads attached to the slider restrict the pram's stability.
  WARNING: Always use the parking brake when parking the pram.
  WARNING: Remember that small parts can be swallowed by your child and can cause choking.
  WARNING: Do not lay any additional mattresses in the pram.
• Please use only original hauck accessories and original hauck spare parts.
• Please use only the supplied carrying bag and make sure that it is firmly attached. Do not put an additional mattress into the carrying bag.
• Avoid extreme usage situations that restrict your control over the child and the pram.

If you are using the pram for your child, you should restrict your tempo to walking, i.e. do not run, jog or skate.
- Do not use any escalators or stairs, and be careful using lifts while your child is in the pram.
- Only use the space allowed for loading and do not exceed the maximum permitted weight of 15kg .
The pram may only be used for transporting one child.
- Please make sure that the child's hands are nowhere near the folding area so as not to risk them being crushed if you have to fold up, unfold or otherwise change the pram or parts of it.

THIS PRAM COMPLIES WITH STANDARD DIN EN 1888:2003-06

Scope of supply (fig. 1)

• Chassis with pushchair superstructure
  Snug nest
• Leg cover
• 4 wheels

1. Assembly

Release the transport safeguard. Erect the pushchair by moving the slide until you can see and hear that the locking mechanisms on both sides have engaged.

2. Mounting the wheels (fig. 2)

Slip both wheels on to the front axle until you hear a click and the metal clips have clicked into place in the axle groove. Check that it fits firmly. ush the axle through the two plastic check rails at the frame ends until it clicks home. Here again, check that it fits firmly. Proceed accordingly with the rear axle.

3. Brakes

To lock the foot brake, press the brake bar down with your foot. To release it again, lift the brake bar with your foot.

Caution! Always lock the brakes when parking the pushchair.

4. Mounting the hood (fig. 3)

Push the hood in the corresponding openings to the left and right of the pushchair superstructure.

5. Swivelling the push bar (fig. 4a, 4b, 4c, 4d)

The push bar can be swivelled to use the pushchair with snug nest. To do so, pull the upper adjusting lever on the push bar and move it over to the other side at the same time. Check that it has engaged correctly.

6. Adjusting the height of the push bar (fig. 5)

Press the adjusting buttons underneath the handle on both sides and adjust the required height. After adjusting the required height, the buttons pop out again.

7. Adjusting the back rest (fig. 6)

To adjust the back rest, pull the metal handle at the back of the rest up and move the back rest back.

The sitting position is achieved by pushing the back rest up until the locking mechanism engages.

8. Adjusting the leg rest (fig. 7)

Bring the leg rest to the required position and hook the metal supports in position under the leg rest.

9. Adjusting the front strap (fig. 8)

Press the adjusting buttons on both sides and adjust the required position. After adjusting the required position, the buttons pop out again.

10. Safety belt

Fit the belt between the legs and around the hips. Adjust the width of the belt to fit your child.

Caution! To avoid any injuries, you should always secure your child with the safety belt.

11. Collapsing (fig. 9)

Pull the lower unlocking levers on both sides of the push bar upwards and push the pushchair down to collapse. Tip: Before collapsing the pushchair, adjust it to the lying position.

12. Fastening the carrying bag (fig. 10)

Do not place an additional mattress in the carrying bag. The carrying bag is securely fixed when you attach D-rings on to the hooks.

In General

Please check the pram functions on a regular basis. Make sure that the frame is stable, the screws are tight, the latching devices are safely locked, the wheels are securely attached and the brakes are in working order. Check the covers occasionally, making sure that the stitching is still firm, and inspect the quality of the plastic parts. Any defective or worn working parts should be replaced immediately. Proceed in the same manner with components that are broken, torn, defect or worn-out. Please use only original hauck replacement parts.

Do not subject your pram to excessive solar radiation. This can lead to a fading of the textile covers and plastic parts.

Cleaning the covers

Remove the cover from the frame by loosening the loops, press studs or screws. Please read the instructions on the sewn-in washing label before washing.

To clean the cover gently, wipe it down evenly using only a damp cloth. When cleaning cloth covers with non-removable lining, please take care not to drench everything. As long as there are no plastic, wood or metal parts on or in the cover, it can be machine-washed at 30^ and spun at medium speed. The cover should be air-dried, but not exposed to blazing sun. Please do not dry the cover in the drier, so as to avoid shrinking. Do not re-fit the covers until they are completely dry.

Cleaning the frame

Dry the pram with a soft cloth after cleaning or after use in rain and snow. Use only mild soapy water or lukewarm water to clean the frame of your pram. Plastic parts can be cleaned with standard cleaners.

Wheel maintenance

Clean and service the wheels regularly. Treatment with a silicon or corrosion spray protects against rust and deposits. Please make sure in winter that road salt residue is removed immediately. Remove dirt from the wheels and axes on a regular basis.

IMPORTANT- KEEP IT FOR LATER READING

CONSERVER CE MODE D'EMPLOI POUR UN USAGE ULTERIEUR ET LE LIRE ATTENTIVEMENT

BELANGRIJK - BEWAAR ALS NASLAGWERK

CONSERVARE PER UNA CONSULTAZIONE SUCESSIVA

hauck GmbH & Co KG

Tel. : [phone] / 986-0

Frohnlacher Str. 8

Fax. : [phone] / 6272

D-96242 Sonnefeld

Email : [e-mail]

Germany

Internet: http://www.hauck.de