WDGA 58F - Uncategorized Wachendorff - Free user manual and instructions
Find the device manual for free WDGA 58F Wachendorff in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Absolute rotary encoder |
| Model | WDGA 58F |
| Manufacturer | Wachendorff |
| Housing Diameter | 58 mm |
| Shaft Type | Hollow shaft, Ø 12 mm (typical) |
| Supply Voltage | 10 to 30 V DC |
| Resolution per Revolution | Up to 16,384 steps (14 bit) |
| Multiturn Sensing Range | Up to 65,536 revolutions (16 bit) |
| Bus Interface | CANopen, PROFIBUS DP, or DeviceNet (variant dependent) |
| Output Code | Binary or Gray (configurable) |
| Protection Class | IP67 (housing), IP65 (shaft) |
| Operating Temperature | -40°C to +85°C |
| Connection | Radial cable or M12 connector |
| Housing Material | Aluminum with epoxy coating |
| Weight | Approx. 500 g |
| Maintenance | Maintenance-free sealed unit |
| Cleaning | Wipe with dry cloth; avoid solvents or pressure washers |
| Safety Features | Reverse polarity protection, short-circuit protection |
| Repair and Spare Parts | Non-field-serviceable; return to manufacturer or authorized service center |
| Certifications | CE, RoHS, EMC compliant |
Frequently Asked Questions - WDGA 58F Wachendorff
How do I set the resolution of the WDGA 58F encoder?
The resolution is set via the configuration software or hardware switches depending on the interface variant. Consult the parameter manual for address settings and scaling options.
Can I use the WDGA 58F outdoors?
Yes, the encoder is rated IP67 for the housing and IP65 for the shaft, making it suitable for harsh environments. Ensure all connectors are properly tightened to maintain protection.
What is the maximum rotational speed?
The maximum speed is typically 3500 RPM for continuous operation. For short durations, up to 5000 RPM may be allowed. Refer to the technical datasheet.
Does the WDGA 58F support multiturn measurement?
Yes, the multiturn version counts up to 65,536 revolutions (16-bit), allowing absolute position feedback over multiple turns without battery backup.
How do I connect the encoder to a PLC?
Connect the bus wires according to the pinout in the manual. For CANopen and PROFIBUS, terminate the bus correctly. Use a male/female M12 connector or cable glands for wiring.
What should I do if the encoder does not communicate?
Check the supply voltage, wiring polarity, and bus termination. Verify the node address and baud rate settings. Use the status LED to diagnose errors.
Is the zero position adjustable?
Yes, the zero position can be set via a teach-in command or by using the programming input. The preset value can also be stored in the non-volatile memory.
How often should I perform maintenance?
The WDGA 58F is maintenance-free under normal conditions. Inspect connectors and cables periodically for damage, and keep the shaft seal free from abrasive particles.
Can I replace the cable myself?
The cable is not user-replaceable. For repair, contact Wachendorff or an authorized service center to ensure the IP protection and accuracy are maintained.
What spare parts are available?
As a sealed and encapsulated unit, there are no internal spare parts available. Only optional mating connectors and cable assemblies can be ordered separately.
User questions about WDGA 58F Wachendorff
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual WDGA 58F - Wachendorff and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. WDGA 58F by Wachendorff.
USER MANUAL WDGA 58F Wachendorff
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Wachendorff
Model : WDGA 58F
Category : Uncategorized