XGS-6320-12X4TR - Network switch Planet - Free user manual and instructions
Find the device manual for free XGS-6320-12X4TR Planet in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Managed Network Switch |
| Model | XGS-6320-12X4TR |
| Brand | Planet |
| Ports | 12 x 10G SFP+, 4 x 40G QSFP+ |
| Switching Capacity | 560 Gbps |
| Forwarding Rate | 416 Mpps |
| MAC Address Table | 32K entries |
| VLAN Support | Up to 4K VLANs |
| Jumbo Frame Support | Up to 9K bytes |
| Layer 3 Features | Static routing, RIP, OSPF, VRRP |
| Management | Web GUI, CLI, SNMP v1/v2c/v3 |
| Power Supply | Dual built-in AC power supplies (redundant) |
| Power Consumption | 120W typical |
| Dimensions (WxDxH) | 440 x 320 x 44 mm (1U rackmount) |
| Weight | 5.5 kg |
| Operating Temperature | 0°C to 50°C |
| Cooling | Fan-based, smart fan control |
| Certification | CE, FCC Part 15 Class A |
| Warranty | 3 years limited |
| Spare Parts & Repairability | No user-serviceable parts; contact Planet support |
Frequently Asked Questions - XGS-6320-12X4TR Planet
How to reset the switch to factory defaults?
Press and hold the reset button on the front panel for 10 seconds while the switch is powered on. The switch will reboot with factory settings. Alternatively, use the command 'configure restore factory-default' via CLI.
What is the default IP address of the switch?
The default IP address is 192.168.0.100 with subnet mask 255.255.255.0. The default username and password are admin / admin.
How to update the firmware?
Download the latest firmware from Planet's support site. Access the web GUI, go to Administration > Firmware Upgrade, select the file, and click 'Upgrade'. The switch will reboot automatically.
How to configure VLANs?
Via web GUI, navigate to VLAN > 802.1Q VLAN. Create a new VLAN ID, assign ports, and set the PVID. For CLI, use commands like vlan 10 and untagged 1-4.
Does the XGS-6320-12X4TR support PoE?
No, this model does not have PoE support. It is a pure data switch for 10G and 40G fiber connections.
How to access the CLI?
You can access the CLI via SSH (port 22) or console cable (RJ45 to DB9). Default SSH credentials are admin / admin. The console speed is 115200 baud.
What is the maximum cable length for SFP+ ports?
For 10G SFP+ modules, the maximum length depends on the transceiver: up to 300m on multi-mode fiber (MMF) or up to 10km on single-mode fiber (SMF).
Does the switch support stacking?
No, this model does not support physical stacking. However, it supports MLAG (Multi-Chassis Link Aggregation) for redundancy.
How to check port status?
In the web GUI, go to Port > Port Statistics. For CLI, use show interfaces status to see link state, speed, and duplex.
What should I do if the switch overheats?
Ensure the vents are not blocked, and the operating temperature is within 0-50°C. Check fan operation via show system environment. If overheating persists, power off and contact Planet support.
User questions about XGS-6320-12X4TR Planet
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Network switch in PDF format for free! Find your manual XGS-6320-12X4TR - Planet and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. XGS-6320-12X4TR by Planet.
USER MANUAL XGS-6320-12X4TR Planet
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Planet
Model : XGS-6320-12X4TR
Category : Network switch