AA120G - Receiver ATLAS - Free user manual and instructions
Find the device manual for free AA120G ATLAS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Audio Receiver |
| Brand | Atlas |
| Model | AA120G |
| Dimensions (W x D x H) | 430 x 300 x 100 mm |
| Weight | 5 kg |
| Power supply | Mains 220-240 V / 50 Hz |
| Output power | 2 x 100 W RMS at 8 ohms |
| Audio inputs | 4 RCA inputs, 1 phono input (MM) |
| Audio outputs | 2 pairs of speakers, preamp output, headphone output |
| Tuner | FM/AM with RDS |
| Main functions | Source selection, volume, balance, tone (treble/bass), loudness, standby |
| Maintenance and cleaning | Clean with a soft, dry cloth. Do not use abrasive products or solvents. |
| Safety | Do not expose to moisture, heat sources. Unplug before cleaning or during thunderstorms. |
| Spare parts and repairability | Parts available from customer service. Repair possible by a certified technician. |
| General information | 2-year warranty. Standby consumption: < 0.5 W. |
Frequently Asked Questions - AA120G ATLAS
How to connect passive speakers to the AA120G receiver?
Use stripped speaker cables. Connect the positive wire to the red terminal and the negative wire to the black terminal. Make sure the speaker impedance is between 4 and 16 ohms. Do not short-circuit the terminals.
How to use the built-in FM/AM tuner?
Press the 'Tuner' button to select FM or AM band. Use the auto search buttons or the dial to tune a station. To store, press and hold a preset button.
What to do if the sound is distorted or weak?
Check speaker and source connections. Make sure the source is not saturated. Set the volume to a reasonable level. If the problem persists, try resetting the device by unplugging it for 30 seconds.
How to adjust balance and tone?
Use the 'Balance' knobs to distribute sound between left and right channels. The 'Bass' and 'Treble' knobs adjust low and high frequencies. For neutral listening, set all controls to center.
Can I connect a turntable without a phono preamp?
Yes, the AA120G receiver has a phono input with a built-in preamp for moving magnet (MM) cartridges. Connect your turntable to the 'Phono' input and attach the ground wire to the GND terminal.
The receiver does not turn on, what to check?
Check that the power cord is properly connected and the mains outlet works. Try pressing the power switch. If nothing happens, the internal fuse may be blown. Consult a certified technician.
How to clean the receiver?
Unplug the device. Use a soft, dry cloth to dust the cabinet. For connectors, a slightly damp cloth may be used, but ensure no moisture enters inside. Never use chemical products.
What is the maximum output power?
The receiver delivers 2 x 100 W RMS at 8 ohms with total harmonic distortion less than 0.05%. Power can reach 150 W per channel at 4 ohms, but prolonged use at high power is not recommended.
Can I use 4 ohm speakers?
Yes, the receiver is compatible with 4 to 16 ohm speakers. With 4 ohm speakers, power will be higher, but ensure good ventilation to avoid overheating.
How to reset the receiver to factory settings?
Turn off the device. Press and hold the 'Power' button for 5 seconds while turning the device back on. Tuner and volume settings will be reset. This operation does not delete stored tone settings.
User questions about AA120G ATLAS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual AA120G - ATLAS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AA120G by ATLAS.
USER MANUAL AA120G ATLAS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ATLAS
Model : AA120G
Category : Receiver