TAZ 6 - 3D Printer LulzBot - Free user manual and instructions
Find the device manual for free TAZ 6 LulzBot in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Large format FDM 3D printer |
| Brand | LulzBot |
| Model | TAZ 6 |
| Build volume (L x W x H) | 280 x 280 x 250 mm |
| Filament diameter | 2.85 mm (3 mm compatible) |
| Extruder | Dual gear, interchangeable, single-use |
| Heated bed | Borosilicate glass with PEI, heated and removable |
| Maximum nozzle temperature | 300 °C |
| Maximum bed temperature | 120 °C |
| Minimum layer height | 50 microns (0.05 mm) |
| Print speed | Up to 200 mm/s |
| Auto leveling | Yes, with leveling probe |
| Connectivity | USB, SD card, Ethernet (via OctoPrint) |
| Control software | Cura LulzBot Edition, Repetier-Host, PrusaSlicer |
| Power supply | 24 V DC, 360 W |
| Dimensions (L x W x H) | 495 x 495 x 525 mm |
| Weight | 21 kg |
| Compatible materials | PLA, ABS, PETG, nylon, polycarbonate, TPU, etc. |
| Noise level | Approximately 50 dB |
| Safety | Emergency stop, thermal protection, removable cover |
| Maintenance | Nozzle cleaning, rod lubrication, firmware updates |
| Spare parts and repairability | Open source parts, easily replaceable, active community |
| Warranty | 1 year (extendable) |
| General information | Robust printer designed for makers and professionals |
Frequently Asked Questions - TAZ 6 LulzBot
How to install and set up the LulzBot TAZ 6 for the first time?
Unpack the printer, remove transport protections, attach the spool holder, plug in the power. Download Cura LulzBot Edition and follow the setup wizard. Perform auto leveling via the touch screen menu. Load filament (press 'Load filament') and start a test print.
Which filaments can I use with the TAZ 6?
The TAZ 6 accepts filaments with a diameter of 2.85 mm (3 mm compatible): PLA, ABS, PETG, nylon, polycarbonate, TPU, wood/metal composites. Adjust nozzle and bed temperature according to the material. Avoid low Shore flexible filaments without a suitable filament guide.
How to troubleshoot first layer issues?
Check that the bed is properly leveled (run Auto Bed Leveling). Clean the bed with isopropyl alcohol. Adjust the initial Z height via the 'Z Offset' menu. Increase bed temperature by 5 °C. Use hairspray or glue stick to improve adhesion.
How to change the nozzle or extruder?
Heat the nozzle to 240 °C, unscrew it with a suitable wrench (7 mm). Replace with a brass or hardened steel nozzle. For the extruder, remove the fan, take out the mounting screws, and disconnect the connector. Refer to the extruder replacement guide on the LulzBot website.
How to calibrate the extruder (e-steps)?
Access the menu Control > Motion > Steps/mm. Mark the filament at 120 mm from the extruder. Extrude 100 mm via the menu, measure the actual distance. Calculate: (current steps/mm * 100) / extruded distance. Adjust the value in the firmware. Repeat until accuracy of ±1 mm.
How to update the firmware on the TAZ 6?
Download the latest version of the Marlin firmware for TAZ 6 from the LulzBot website. Compile it with Arduino IDE or use a precompiled .hex file. Connect the printer via USB, launch Repetier-Host or OctoPrint, go to 'Configuration' and select the file. Be careful to preserve custom settings.
What to do in case of a nozzle clog?
Heat the nozzle to 260 °C (max 300 °C). Perform a cold pull: insert nylon filament or a cleaning rod, push gently then pull sharply. If the clog persists, disassemble the nozzle and clean it with a needle. Check that the PTFE tube is not degraded.
How to maintain the LulzBot TAZ 6?
Clean the bed regularly with alcohol. Lubricate the linear rods with PTFE oil every 3 months. Dust the fans. Check belt tension. Replace the air filter if present. Update firmware and material profiles.
How to connect the TAZ 6 to OctoPrint?
Install OctoPrint on a Raspberry Pi. Connect the TAZ 6 via USB to the Pi. In OctoPrint, select the serial port and set the baud rate to 250000. Install the 'LulzBot TAZ 6' plugin for profiles. You can then control the printer remotely and view the webcam.
What safety precautions should be taken?
Place the printer on a stable and non-flammable surface. Do not leave it unattended during long prints. Use adequate ventilation (air extraction for ABS). Keep children and pets away. Disconnect power before any intervention. Wear gloves when handling hot parts.
User questions about TAZ 6 LulzBot
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your 3D Printer in PDF format for free! Find your manual TAZ 6 - LulzBot and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TAZ 6 by LulzBot.
USER MANUAL TAZ 6 LulzBot
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : LulzBot
Model : TAZ 6
Category : 3D Printer