FS-1100 - Laser printer KYOCERA - Free user manual and instructions

Product type	Monochrome laser printer
Brand	KYOCERA
Model	FS-1100
Dimensions (W x D x H)	375 x 393 x 250 mm
Weight	10 kg (without toner cartridge)
Power supply	120 V AC, 60 Hz, 7.5 A / 220-240 V AC, 50/60 Hz, 3.9 A
Power consumption (max)	842 W (120 V) / 849 W (220-240 V)
Power consumption (standby)	5.7 W (120 V) / 6.5 W (220-240 V) with EcoFuser active
Print speed	Up to 28 ppm (A4) / 30 ppm (Letter)
Maximum resolution	1200 dpi (Fine mode)
Paper tray capacity	250 sheets (80 g/m²)
Multipurpose tray	Manual feed 1 sheet
Standard / maximum memory	32 MB / 544 MB
Processor	PowerPC 405F5 at 360 MHz
Standard interfaces	USB Hi-Speed
Options	Memory module, paper feeder PF-100 (250 sheets), network card IB-23, CompactFlash card
Toner cartridge	Starter cartridge (2000 pages), standard cartridge (4000 pages) at 5% coverage
Monthly duty cycle	Average 1500 pages, maximum 15000 pages
Special features	Manual duplex printing, EcoPrint mode, standby mode
Maintenance and cleaning	Replacing the toner cartridge, cleaning the charger wire and the heat roller
Safety	Compliant with CE standards, Class 3B laser, automatic shutdown in case of error
Operating environment	Temperature 10 to 32.5°C, humidity 15 to 80%, max altitude 2500 m

Frequently Asked Questions - FS-1100 KYOCERA

How to replace the toner cartridge?

Open the top cover, turn the lock lever to the unlock position, then remove the used cartridge. Take out the new cartridge, shake it laterally at least five times to distribute the toner, remove the protective paper and insert it into the printer until it clicks. Close the cover. Note: Use only genuine KYOCERA cartridges.

What to do in case of a paper jam?

The Jam indicator lights up. Identify the jam location (tray, MP tray, inside, or rear cover). Remove the jammed paper by gently pulling it in the feed direction. If necessary, open the top cover and front cover, then lift the processing unit. After removing the jam, close all covers and printing resumes automatically.

How to clean the printer?

Open the top cover and front cover. Remove the processing unit and drum. Use a lint-free cloth to clean the heat roller (metal). Slide the charger cleaner (green) back and forth two or three times. Replace the drum and processing unit, then close the covers. Important: Do not touch the black transfer roller.

How to install the printer driver on Windows?

Connect the printer via USB and turn it on. Insert the supplied CD-ROM. If installation does not start, run Setup.exe. Accept the agreement, choose 'Express mode' for automatic detection, select the detected printer and click 'Install'. If the Windows Security message appears, click 'Install this driver anyway'.

What types of paper can I use?

The standard tray accepts paper from 60 to 120 g/m². The multipurpose tray (manual feed) accepts from 60 to 220 g/m², including transparencies, labels, envelopes, and cardstock. Use paper designed for laser printers. Supported sizes range from A4 to Legal and custom sizes (70 x 148 to 216 x 356 mm).

How to print manually on both sides?

In the printer driver, select the 'Layout' tab and check 'Manual duplex printing'. Choose the binding direction (long edge or short edge). The printer prints the even pages first. Remove the printed sheets, fan them, and reload them into the tray with the instruction sheet facing up. Click OK to print the odd pages.

What does the flashing Toner indicator mean?

The fast flashing of the Toner indicator means the toner cartridge is almost empty. You can still print a certain number of pages, but it is recommended to plan a replacement soon. If the indicator stays on continuously, the cartridge is empty and the printer stops: replace it immediately.

How to reduce energy consumption?

Enable the automatic sleep mode (default after 15 minutes of inactivity) and keep the EcoFuser function enabled in Configuration Tool. EcoFuser cuts the heating of the fuser unit in standby, reducing consumption to about 5.7 W (120 V). You can also print in EcoPrint mode via the driver to save toner.

Can I use recycled paper?

Yes, the printer accepts recycled paper. Make sure it meets the same specifications as standard paper (weight 60-120 g/m², humidity level 4-6%, long grain). Select the paper type 'Recycled' in the driver or Configuration Tool for optimal settings.

How to add memory to the printer?

Memory expansion requires a technician. The printer has a DIMM slot accepting modules of 64, 128, 256 or 512 MB. After installation, print a configuration page to verify recognition. The maximum total memory is 544 MB.

USER MANUAL FS-1100 KYOCERA

IBM Program License Agreement

THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS ("PROGRAMS") WHICH BELONG TO INTERNATIONAL BUSINESS MACHINES CORPORATION ("IBM"). THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE, THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL REFUND. IF YOU DO NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS, THEN YOU WILL BE ASSUMED TO HAVE AGREED TO THESE TERMS AND CONDITIONS.

The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in the country where you acquired the Programs. You obtain no rights other than those granted you under this license.

The term "Programs" means the original and all whole or partial copies of it, including modified copies or portions merged into other programs. IBM retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs.

1. License

Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the Programs and the device to another party.

If you transfer the Programs, you must transfer a copy of this license and any other documentation to the other party. Your license is then terminated. The other party agrees to these terms and conditions by its first use of the Program.

You may not:

1. use, copy, modify, merge, or transfer copies of the Program except as provided in this license;
2. reverse assemble or reverse compile the Program; or
3. sublicense, rent, lease, or assign the Program.

2. Limited Warranty

The Programs are provided "AS IS."

THERE ARE NO OTHER WARRANTYES COVERING THE PROGRAMS (OR CONDITIONS), EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.

3. Limitation of Remedies

IBM's entire liability under this license is the following;

For any claim (including fundamental breach), in any form, related in any way to this license, IBM's liability will be for actual damages only and will be limited to the greater of:

1. the equivalent of U.S.$25,000 in your local currency; or
2. IBM's then generally available license fee for the Program

This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable.

IBM will not be liable for any lost profits, lost savings, or any incidental damages or other economic consequential damages, even if IBM, or its authorized supplier, has been advised of the possibility of such damages. IBM will not be liable for any damages claimed by you based on any third party claim. This limitation of remedies also applies to any developer of Programs supplied to IBM. IBM's and the developer's limitations of remedies are not cumulative. Such developer is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions, so they may not apply to you.

4. General

You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this license. In either event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including personal property taxes, resulting from this license. Neither party may bring an action, regardless of form, more than two years after the cause of action arose. If you acquired the Program in the United States, this license is governed by the laws of the State of New York. If you acquired the Program in Canada, this license is governed by the laws of the Province of Ontario. Otherwise, this license is governed by the laws of the country in which you acquired the Program.

Monotype Imaging License Agreement

1. "Software" shall mean the digitally encoded, machine readable, scalable outline data as encoded in a special format as well as the UFST Software.
2. You agree to accept a non-exclusive license to use the Software to reproduce and display weights, styles and versions of letters, numerals, characters and symbols ("Typefaces") solely for your own customary business or personal purposes at the address stated on the registration card you return to Monotype Imaging. Under the terms of this License Agreement, you have the right to use the Fonts on up to three printers. If you need to have access to the fonts on more than three printers, you need to acquire a multi-user license

agreement which can be obtained from Monotype Imaging. Monotype Imaging retains all rights, title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement.

1. To protect proprietary rights of Monotype Imaging, you agree to maintain the Software and other proprietary information concerning the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces.

2. You agree not to duplicate or copy the Software or Typefaces, except that you may make one backup copy. You agree that any such copy shall contain the same proprietary notices as those appearing on the original.

3. This License shall continue until the last use of the Software and Typefaces, unless sooner terminated. This License may be terminated by Monotype Imaging if you fail to comply with the terms of this License and such failure is not remedied within thirty (30) days after notice from Monotype Imaging. When this License expires or is terminated, you shall either return to Monotype Imaging or destroy all copies of the Software and Typefaces and documentation as requested.

4. You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or decompile the Software.

5. Monotype Imaging warrants that for ninety (90) days after delivery, the Software will perform in accordance with Monotype Imaging-published specifications, and the diskette will be free from defects in material and workmanship. Monotype Imaging does not warrant that the Software is free from all bugs, errors and omissions.

6. THE PARTIES AGREE THAT ALL OTHER WARRANTYES, EXPRESSED OR IMPLIED, INCLUDING WARRANTYS OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, ARE EXCLUDING.

7. Your exclusive remedy and the sole liability of Monotype Imaging in connection with the Software and Typefaces is repair or replacement of defective parts, upon their return to Monotype Imaging.

8. IN NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY ABUSE OR MISAPPLICATION OF THE SOFTWARE AND TYPEFACES.

9. Massachusetts U.S.A. law governs this Agreement.

10. You shall not sublicense, sell, lease, or otherwise transfer the Software and/or Typefaces without the prior written consent of Monotype Imaging.

11. Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate. Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c)(2).

12. YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR REPRESENTATION NOT CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY. BY OPENING THIS DISKETTE PACKAGE, YOU AGREE TO ACCEPT THE TERMS AND CONDITIONS OF THIS AGREEMENT.

Fabricant: Kyocera Mita Corporation Tamaki Plant

Product name: Page Printer

Impression recto-verse (Pour FS-1300D uniqueness)

Programme Energy Star (ENERGY STAR®) (Pour FS-1300D uniqueness)

Ready, Data, Jam, Attention, Toner 1-5

PASSIONATE PEOPLE. FROM ALL OVER THE WORLD.

KYOCERA MITA EUROPE B.V.

EUROPEAN HEADQUARTERS

Hoeksteen 40

(Europe, Middle East & North Africa)

Hoeksteen 40

KYOCERA MITA South Africa (Pty) Ltd.

527 Kyalami Boulevard, Kyalami

Business Park · ZA-1685 Midrand

Phone: [phone]

Fax: [phone]

www.kyoceramita.co.za

SPAIN

8 Beacontree Plaza, Gillette Way,

Reading, Berkshire RG2 OBS

Phone: [phone]

Fax: [phone]

www.kyoceramita.co.uk

2-28, 1-Chome, Tamatsukuri, Chuo-ku,

Osaka 540-8585, Japan

Phone: [phone]

Fax: [phone]

www.kyoceramita.com

USA

KYOCERA MITA America, INC.

(Head office)

225 Sand Road, P.O. Box 40008

Fairfield, New Jersey 07004-0008, USA

www.kyoceramita.com/us

KYOCERA CORPORATION

JAPAN

KYOCERA CORPORATION

(Corporate Headquarters)

6 Takeda Tobadono-cho, Fushimi-ku

Kyoto 612-8501, Japan

Phone: [phone]

Fax: [phone]

www.kyocera.co.jp

KYOCERA