Soluna II-60 - Lighting ROLLEI - Free user manual and instructions
Find the device manual for free Soluna II-60 ROLLEI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Studio flash |
| Brand | Rollei |
| Model | Soluna II-60 |
| Power | 60 Ws |
| Guide number | 28 (ISO 100, 1 m) |
| Color temperature | 5600 K |
| Modeling lamp | Yes, 60 W (halogen) |
| Power adjustment | Continuously variable (from 1/16 to full power) |
| Recycle time | Approximately 2-3 seconds |
| Number of flashes | Up to 800 (full power) |
| Power supply | Mains 230 V~ 50/60 Hz |
| Power consumption | 300 W maximum |
| Dimensions (W x D x H) | 20 x 15 x 15 cm |
| Weight | 1.5 kg |
| Mounting | Shoe or tripod (16 mm thread) |
| Synchronization | Sync cable, slave cell, test button |
| Thermal protection | Built-in thermal fuse |
| Housing material | Impact-resistant ABS plastic |
| Care and cleaning | Clean with a soft, dry cloth. Do not use solvents. |
| Safety | Do not expose to moisture. Unplug before any maintenance. |
| Spare parts | Flash tube, modeling lamp, sync cable |
| Repairability | Repair by qualified technician recommended |
| Warranty | 2 years (according to local legislation) |
Frequently Asked Questions - Soluna II-60 ROLLEI
How to adjust the power of the Soluna II-60 flash?
Turn the power adjustment knob (usually located on the back) to adjust the power from 1/16 to full power. An LED indicator displays the selected level.
Can I use this flash with a wireless trigger?
Yes, the Soluna II-60 has a built-in slave cell. Place a wireless trigger nearby to synchronize wirelessly.
What is the color temperature of the flash?
The color temperature is approximately 5600 K, which corresponds to daylight. The halogen modeling lamp is adjusted to match.
How to replace the flash tube?
Unplug the device, remove the reflector, then unscrew the protective cover. Disconnect the cables of the defective tube and install the new tube in reverse order. Contact a technician if necessary.
The flash does not fire, what to do?
First check the power supply (mains cable or battery). Make sure the synchronization mode is correct (cable or slave). Test with the test button. If still no flash, the tube or electronics may be defective.
Can I use the flash in continuous (stroboscopic) mode?
No, the Soluna II-60 is a monoflash, not a strobe. It produces only one flash per trigger.
What is the lifespan of the flash tube?
Under normal use, the flash tube can last about 50,000 to 100,000 flashes. This depends on power and frequency of use.
How to clean the flash?
Use a soft, dry cloth to wipe the housing. For the reflector, use an anti-static cloth. Never use chemicals or water.
Does the flash get very hot?
During prolonged use, the housing may become hot, especially with full-power flashes. This is normal. Allow a rest interval between series to avoid overheating.
Where to find spare parts?
Parts such as flash tubes, modeling lamps, and cables are available from authorized Rollei dealers or online. Always use original parts.
User questions about Soluna II-60 ROLLEI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lighting in PDF format for free! Find your manual Soluna II-60 - ROLLEI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Soluna II-60 by ROLLEI.
USER MANUAL Soluna II-60 ROLLEI
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ROLLEI
Model : Soluna II-60
Category : Lighting