PAS 300 - Water pump EDEN - Free user manual and instructions
Find the device manual for free PAS 300 EDEN in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Water pump |
| Brand | Eden |
| Model | PAS 300 |
| Power supply | 230 V ~ 50 Hz |
| Rated power | 300 W |
| Max flow rate | 30 L/min |
| Max head | 30 m |
| Connection diameter | 1 inch (25 mm) |
| Dimensions (L × W × H) | 30 × 20 × 25 cm |
| Weight | 5 kg |
| Body material | Stainless steel and polypropylene |
| Recommended use | Gardening, watering, transfer of clean water |
| Protection rating | IPX4 |
| Max water temperature | 35 °C |
| Power cable length | 1.5 m |
| Noise level | < 70 dB(A) |
| Warranty | 2 years |
| Maintenance and cleaning | Clean the suction filter regularly |
| Safety | Thermal protection and dry run protection |
| Spare parts available | Seals, non-return valve, impeller |
| Repairability | Estimated repairability score 6/10 |
Frequently Asked Questions - PAS 300 EDEN
How to install the Eden PAS 300 water pump?
Place the pump on a flat and stable surface. Connect the suction hose (with strainer) and the discharge hose. Ensure that the connections are watertight. Plug the pump into a 230 V socket protected by a residual current circuit breaker.
Do I need to prime the pump before first use?
Yes, the pump must be primed. Fill the pump body with water through the filling port until water flows out from the discharge. Close tightly before starting.
What to do if the pump does not start?
Check the power supply, fuse, and circuit breaker. Ensure that the thermal protection has not tripped (wait for cooling). Check that the water level is sufficient and that the strainer is not clogged.
Why does the pump lose flow rate?
This may be due to a clogged filter, dirty strainer, leak in the suction hose, or excessive discharge height. Clean the components and check for leaks.
How to maintain the Eden PAS 300 pump?
After each use, rinse with clean water. Clean the suction filter regularly. In winter, fully drain the pump and store it frost-free. Lubricate seals if necessary.
The pump makes an abnormal noise, what to do?
A knocking noise may indicate a lack of water (dry running) or air in the circuit. Stop immediately, re-prime and bleed air. A deep noise may be due to cavitation - check the suction height.
Can I use the pump with rainwater?
Yes, but filter the water to avoid damaging the impeller. The pump is designed for clean water without abrasive particles. For slightly dirty water, use an upstream filter.
What is the maximum suction height?
The theoretical maximum suction height is about 8 meters. In practice, limit to 6 meters for optimal operation. Beyond that, the pump may not prime.
How to store the pump in winter?
Drain all water from the pump and hoses. Disconnect and store in a dry, frost-free location. Remove fittings and clean metal parts with a light rust inhibitor.
Where to find spare parts for the PAS 300?
Contact Eden after-sales service or an authorized dealer. Common parts (seals, valve, impeller) are available on order. Have the model and serial number ready.
User questions about PAS 300 EDEN
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water pump in PDF format for free! Find your manual PAS 300 - EDEN and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PAS 300 by EDEN.
USER MANUAL PAS 300 EDEN
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : EDEN
Model : PAS 300
Category : Water pump