Bluetooth Speaker - Docking Station HAMA - Free user manual and instructions

Product Type	Bluetooth Docking Station
Brand	Hama
Model	Bluetooth Speaker
Dimensions (approx.)	20 x 10 x 10 cm
Weight	500 g
Power Supply	USB (5 V) or rechargeable internal battery
Battery Capacity	2000 mAh
Battery Life	Up to 10 hours
Bluetooth Version	5.0
Bluetooth Range	Up to 10 meters
Main Functions	Wireless audio playback, hands-free kit, auxiliary input, FM radio
Auxiliary Input	3.5 mm jack socket
Storage	microSD card reader
Output Power	2 x 3 W
Maintenance and Cleaning	Wipe with a soft, dry cloth. Do not use abrasive products.
Safety	Do not expose to water or excessive heat. Do not open the device.
Spare Parts and Repairability	No parts available. In case of failure, contact customer service.
Package Contents	Speaker, USB cable, user manual
General Information	Manual downloadable in PDF format from the manufacturer's website.

Frequently Asked Questions - Bluetooth Speaker HAMA

How do I connect my phone to the Bluetooth speaker?

Activate Bluetooth on your phone and select 'Hama Bluetooth Speaker' from the list of available devices. The PIN code is usually '0000'.

How do I recharge the speaker's battery?

Use the provided USB cable to connect the speaker to a mains adapter (5V) or a computer USB port. The LED indicator shows charging status.

Can I use the speaker while charging?

Yes, it is possible to use the speaker while charging, but this may lengthen the charging time.

How do I make a hands-free call?

When a call comes in, press the multifunction button to answer. Press again to hang up. The built-in microphone allows you to speak.

What should I do if the speaker does not turn on?

Check that the battery is charged. Plug the speaker into the charger for at least 30 minutes, then try again. If the problem persists, contact customer service.

How do I use the FM radio?

Press the 'Mode' button until FM radio is selected. Use the + and - buttons to automatically search for stations. The USB cable can serve as an antenna.

Can I use a microSD card?

Yes, insert a microSD card (up to 32 GB) into the designated slot. The speaker will automatically play MP3 audio files.

How do I clean the speaker?

Use a soft, dry cloth. Never use liquids or harsh chemicals. Avoid leaving the speaker in a humid environment.

Is the speaker waterproof?

No, this model is not waterproof. Avoid any contact with water or liquids.

Where can I find the full manual?

The complete manual in PDF format is available for free download on the official Hama website or through platforms like notice-facile.com.

USER MANUAL Bluetooth Speaker HAMA

Bluetooth® Speaker + Qi Charger

Line drawing of a rectangular electronic device labeled 'hama' with no additional text or symbols

Controls and Displays

1. On/off switch
2. AUX-IN input (3.5 mm stereo jack)
3. Micro-USB connection (USB CHARGE)
4. Integrated microphone
5. function button -
6. function button
7. function button +
8. Status LED
9. Qi - charging area
10. NFC connection area

Thank you for choosing a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe p for future reference. If you sell the device please pass these operating instructions on the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention-specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

• Bluetooth® speaker + 'Power Brick' Qi charger
• Micro-USB charging cable
  • 3.5 mm audio cable
  • These operating instructions

3. Safety Notes

• The product is intended for private, non-commercial use only.
• Do not use the product in the immediate vicinity of heaters or other heat sources in direct sunlight.
• Keep this product, as all electrical products out of the reach of children!
• Do not drop the product and do not it to any major shocks.
• Do not operate the product outside the power limits given in the specifications.

• Do not use the product in areas where the use of electronic devices is not permitted.

• In order to prevent damage caused by overheating, make sure the product is not covered by textiles, metal or other objects.

• Be considerate. Loud volumes can have a detrimental effect on your surroundings.
• Do not open the device or continue to operate it if it becomes damaged.
• Since the battery is integrated and cannot be removed, you will need to dispose of product as a whole. Do this in compliance with the legal requirements.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
• Dispose of packaging material immediately according to locally applicable regulations.
  e, Do not modify the product in any way.
  n Doing so voids the warranty.

4. Getting Started and Operation – Speaker

4.1 Switching the product on and off

- Slide the on/off switch (1) upward to switch on the speaker. An acoustic signal will sound and the status LED (8) will likely up briefly.

Tide the on/off switch (1) downward to switch off the speaker.

Note - Automatic shutdown

Note that the speaker will automatically switch off after 10 minutes without action (no audio playback/no Bluetooth® function).

4.2 Charging the battery

Warning - Rechargeable battery

• Only use suitable charging devices with USB connections for charging.
• As a rule, do not use charging devices or USB connections that are defective and do not try to repair them yourself.
• Avoid storing, charging or usinguctsbatteries in extreme temperatures.

• When stored for a long period of exposure time, batteries should be charged regularly (at least every three months).

• Charge the speaker fully before using the first time.

• Connect the included Micro-USB charging cable to the speaker's Micro-USB port
• Connect the unused connector on the Micro-USB charging cable to a suitable USB charger. Please refer to the operating instructions for the USB charger used.
• The status LED (8) lights up constantly joined during the charging process. If the battery is fully charged, the status (8) will go out.

4.4fBluetooth® pairing

Note

• Check whether your mobile device ng (MP3 player, mobile phone, etc.) is Bluetooth® capable.
  In If not, you can only use the speake for playback using the included audio cable.
• Note that the maximum range for Bluetooth® is 10 metres without obstacles such as walls, people, etc.

Note - Charging

• It takes approx. 6-7 hours to completely charge the product.
• The speaker's battery can be char whether the speaker is on or off
• If the battery capacity is less than 10%, the speaker will emit two acoustic signals. You will only receive this information if the speaker is o
• Depending on the terminal device connected Bluetooth®), the speaker's battery level will appear the device.

- The actual battery life varies depending on use of the device, the settings and ambient conditions (rechargeable batteries have a limited service life).

4.3 Audio playback via the included audio cable (3.5 mm jack)

• Ensure that the speaker is switched off
• Connect your mobile terminal device (MP3 player, smartphone, etc.) and the AUX-IN
  input (2) of the speaker using the incl 3.5 mm audio cable.
• Set the volume on your terminal device a low level.
• Switch on the speakers as described, in Switching the product on and off.
• Press the function button — (7) to red the volume.
• Press the function button + (5) to increase the volume.

- Make sure that yBluetooth® capable terminal device is on Bluetooth® is geactivated.

• Make sure that the speaker is located with the Bluetooth ^® range of max. 10 metres.

- Switch on the speakers as described in Switching the product on and off. Press and hold the function button

on(6) for approximately 3 seconds until an acoustic signal sounds and the status LED (8) flashes continually.

- on Open the Bluetooth® settings on your terminal device and wait until PowerBrick appears in the list Bluetooth® devices found.

- Select PowerBrick and wait until the speaker is listed as connected in the Bluetooth® settings on your terminal device. An short acoustic signal confirms that connection was successful.

• The status LED (8) now remains blue.

Note -Bluetooth® password

Some terminal devices require a password in order to connect to another Bluetooth® device.

- If your terminal device requests a password for connection to the ice speaker, enter 0000.

Note

Please note that you cannot establish the Bluetooth® connection described under 4.4 and 4.5 if an audio cable is connected.

Note - Connection to a new device

• If you want to connect a new Bluetooth® terminal device to the speaker, press and hold the function button (6) for approximately 3 seconds until the status LED (8) begins to flash blue and an acoust signal sounds.
• The current connection is disconnected and the search for next terminal devices starts.
• The speaker always stores the last eight terminal devices paired.
• The speaker will automatically connect to the last terminal device paired when it is switched on the next time.

.5 Automatic Bluetooth® connection (after successful pairing)

- Make sure that yBluetooth®-capable terminal device is on Bluetooth® is activated.

- Make sure that the speaker is located the Bluetooth® range of max. 10 metres.

- Switch on the speaker as described in 4.1 Switching the product on and off.

• After successful connection, the status (8) will light up in blue. An acoustic confirms that connection was successful.

Note - Connection impaired

After the speaker and terminal device have been paired, a connection is established automatically. If the Bluetooth® connection is not established automatically, check the following:

• Check the Bluetooth® settings of your terminal device to see whether PowerBrick is connected. If not, repeat the steps listed under Bluetooth® pairing.

• Check whether your terminal device and the speaker are less than 10 metres apart. If not, move them closer together.

• Check whether obstacles are impairing the range. If so, move the devices closer together.

• Check whether the audio cable is connected to the speaker. If so, disconnect it.

4.6 Audio playback (viBluetooth®)

Start and control audio playback on the connected terminal device accordingly. Alternatively, audio playback can also be controlled on the speaker (if the connected device supports this function).

• Press the ▶ function button (6) to start or pause audio playback.
• Briefly press the function button + (5) to increase the volume.
• Briefly press the function button - (7) to reduce the volume.
• Press and hold the + function button (5) jump forward one title.
• Press and hold the - function button (7) jump backward one title.

4.7 Hands-free function

You can use the speaker as a hands-free s for your mobile phone. For this function, the within mobile phone must be connected to the speaker via Bluetooth®.

- Press the function button (▶) once to answer an incoming call.

LEDPress and hold the function button ▶ signal for approx. 2 seconds to reject an incoming call.

• You can put a call on hold by pressing holding the function button (6) for approximately 2 seconds.
• Press and hold the function button (6) again to continue the call.
• During a call, press the function button ▶|| (6) once to end the call.

Note - Call quality

To increase the call quality, make sure that you are near the speaker with your mobile phone during the call.

5. Operation - Induction Charging Function (Qi)

Do not put any bank cards or similar cards with magnetic strips, or other magnetically sensitive objects, on the product. The data on the cards could damaged or deleted.

Warning - Qi charger

Ensure that there are no metal parts (for example, metal plate for magnetic holder) on the back of your terminal device. Metal may heat up significantly in the field of the induction charger, causing damage to your terminal device and/or the charger.

• Connect the included Micro-USB cable to the Micro-USB input (3) on the speaker a to a suitable USB charger if an external power supply is available. Please refer to the operating instructions for the USB charger used.
• When the power supply is active, the sta arLED (8) lights up.
• Lay your terminal device with the back to the induction charging area (9).

Charging starts as soon as an effective induction field has been generated. The status LED (8) changes colour. The current charging status appears on your terminal device.

- If no connection can be established through induction, you may have to change the position of your terminal device (B).

Charging stops automatically once your device's battery is fully charged. The status: LED (8) changes colour.

Remove your terminal device from the induction charging area and disconnect the speaker from the power supply.

6. Operation - NFC Connection

Note

• To be able to charge your terminal device using the induction charging function, your terminal device must be compatible with induction charging technology. For more information, please refer to the operating instructions of your terminal device.
• Note that the presence of mobile phone cases, covers or other materials between the induction charging area and the back of your terminal device can interfere with charging or even prevent it.
• The induction charging function can also be used without an external power supply; in this case, the battery built in the speaker is used. The battery should be fully charged, and the rate at which discharges will depend on the number of functions that are used simultaneously.
• Playback of audio filesBluetooth® or the included audio cable is not possible while using the induction charging function!

Note

• To be able to connect your terminal device to the speaker using NFC, your terminal device must be compatible with NFC technology. For more information, please refer to the operating instructions of your terminal device.
• Note that the presence of mobile phone cases, covers or other materials between the speaker and the back of your terminal device can interfere with charging or even prevent it.

Note that NFC has a short d transmission range of about 10 cm. ch it

Switch on the speaker as described in 4.1

Switching the product on and off.

• Make sure that the NFC function on your terminal device is turned on and the terminal device is not in lock mode (lock screen).
• Turn the speaker round and place your terminal device on the NFC connection are (10), marked by the NFC symbol on the speaker's device label. The status LED (8) will flash during the connection attempt.

- After a successful NFC connection, the status LED (8) is constantly lit. The sp can be put back in its normal position and the terminal device placed on the upper side.

7. Care and Maintenance

• Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
• Make sure that water does not get the product.

8. Warranty Disclaimer

Hama GmbH & Co. KG assumes no liability country. This symbol on the product, the and provides no warranty for damage resulting manual or the package indicates from improper installation/mounting, improper that a product is subject to these regulation use of the product or from failure to observe recycling, reusing the materials or other the operating instructions and/or safety not forms of utilising old devices/Batteries, you a

9. Service and Support

Please contact Hama Product Consulting if have any questions about this product. Hotline: [phone] (German/English Further support information can be found here: www.hama.com

10. Recycling Information

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices as well as batteries must not be disposed of household waste. Consumers are obliged by law to return electrical and electronic devices so well as batteries at the end of their selves to the public collecting points set up this purpose or point of sale. Details to this defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulation by recycling, reusing the materials or other forms of utilising old devices/Batteries, you a making an important contribution to protecting our environment.

11. Declaration of Conformity

sh) C€ Hama GmbH & Co. KG hereby declares that the device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. See www.hama.com for the declaration conformity with the relevant directive.

12. Technical Data

Portable Bluetooth® speaker
Bluetooth® technology	Bluetooth® v4.0 Class II
Supported profiles	A2DP V1.2, AVRCP V1.4, HFP V1.6
Frequency for the Bluetooth® transfers	2,402 GHz ~ 2,480 GHz
Bluetooth® transfer power	Max. 4 dBm
Frequency	180 Hz - 20 kHz
Range < 10 m
Maximum number of paired devices	1
NFC
NFC®- frequency	13.56 MHz
Range ≤2.5 cm
NFC® transfer	Peer-to-Peer
Qi induction charger
Input Max. 5V	---0,25V 1500 mA
Output Max. 5V	---0,25V 1000 mA
Speaker
Max. music output	10 W
Sound system	Stereo
Impedance 4 Ω
Distortion (THD)	≤ 5%
Dimensions	14,1 x 7,5 x 4,9 cm
Weight 432 g
Connections	3.5 mm stereo plugAUX input, Micro-USB for charging function
Battery
Type	3.7V Li-lon min.: 4400 mAh / 16.28 Wh
Charging voltage	Max. 5V ---0,25V 900 mA
Charging time	~ 6 - 7 h
Operating time	Via Bluetooth®: ~ 5 hVia AUX: ~ 30 hVia a combination of Bluetooth® and Qi inductive charging: ~ 2 h(depending on volume and audio content)

4.6 Lecture audio (viaBluetooth®)

Avertizare - accumulator