DO7033 - Beard trimmer DOMO - Free user manual and instructions

Brand	DOMO
Model	DO7033
Product type	Beard trimmer
Dimensions (L x W x H)	Approx. 15 x 4 x 4 cm
Weight	Approx. 200 g
Power source	Rechargeable Li-Ion battery
Input voltage	100-240 V AC, 50/60 Hz (adapter)
Battery life	Approx. 60 minutes
Charging time	Approx. 8 hours
Charge indicator	LED
Cordless operation	Yes
Blades	Self-sharpening stainless steel
Length adjustment	Adjustable cutting comb (1-10 mm)
Included accessories	Cutting comb, cleaning brush, USB cable
Care and cleaning	Removable water-washable blades, lubricating oil included
Water resistance	Splash resistant (IPX5)
Safety	Automatic shut-off after 10 min, lockable blade
Spare parts and repairability	Replacement blades available
Warranty	2 years
Package contents	Trimmer, comb, USB cable, brush, oil, manual

Frequently Asked Questions - DO7033 DOMO

How do I adjust the cutting length?

Use the provided adjustable cutting comb. Slide it onto the trimmer and move it to select the desired height (1 to 10 mm).

The trimmer is not charging, what should I do?

Check that the USB cable is properly connected to the trimmer and to a mains adapter (5V/1A min). Try another cable or USB port. If the problem persists, contact customer service.

How do I clean the blades?

Remove the cutting head. The blades can be rinsed under running water. Dry them thoroughly and apply a drop of lubricating oil before reassembling.

Can I use the trimmer in the shower?

No, this device is splash resistant (IPX5) but not submersible. Avoid immersion and use in the shower.

How long does a full charge last?

The battery life is approximately 60 minutes after a full 8-hour charge.

How do I replace the blades?

Unclip the old blade unit by pressing the side clips. Insert the new unit until it clicks. Make sure it is securely attached.

The trimmer stops by itself during use

This is normal if used for more than 10 minutes: the automatic shut-off safety feature activates. Restart it by pressing the on/off button.

Can I trim nose hair with this device?

No, this device is designed only for beard. For the nose, use a specific nose trimmer.

Are the blades suitable for sensitive skin?

Yes, the stainless steel blades are designed to be gentle. Use a firm but light motion. If irritation occurs, stop use.

Where can I find spare parts?

Replacement blades are available from your retailer or on the DOMO website. Refer to model DO7033.

USER MANUAL DO7033 DOMO

Electric toothbrush with black and silver model, accompanied by multiple hair clipers (no visible text or symbols)

GARANTIEVOORWAARDEN

CONDITIONS DE GARANTIE

This appliance has a two year warranty period. During this period the manufacturer is responsible for any failures which are the direct result of construction failure. When these failures occur the appliance will be repaired or replaced if necessary. The warranty will not be valid when the damage to the appliance is caused by wrong use, not following the instructions or repairs executed by a third party. The warranty will only be valid if the warranty application has been completed by the dealer at the time of purchase. All parts, which are subject to wear, are excluded from the warranty.

ZÁRUKA

RECYCLING INFORMATIONEN

RECYCLING INFORMATION

The symbol ☒ on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be brought to the applicable collection point for recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service of the shop where you purchased the product.

INFORMACE O RECYKLACI ODPADU

If the supply cord is damaged, it must be replaced by manufacturer of its service agent or a similarly qualified person in order to avoid a hazard.

Six black hairbrush icons arranged in two rows, each labeled with the number 5 (no text or symbols on the icons themselves)

GEBRUIK

1. Cutting unit
2. Cutting length fi ne adjustment
3. Charging level display LED
4. On/off switch
5. Charging station/holder
6. Cutting length attachments
7. Thinning attachment

Six black hairbrush icons arranged in two rows, each labeled with the number 5 or 6 (no text or symbols on the icons themselves)

SAFETY INFORMATION

- Read through these instructions carefully before switching the device on.

To avoid a potentially deadly electric shock and/or fire, please observe the following. Do not use the device near filled bathtubs or sinks or near other containers filled with liquids.

• When finished using the device or for cleaning, pull out the mains plug
• Do not use the device while bathing.
• Never immerse the device or the cable with plug-in mains adapter in water or other liquids.
• If the device should fall into water, be absolutely sure to pull the mains adapter out of the socket with earth contact before reaching into the water.
• Never hold the mains adapter if your hands are wet, particularly if you want to plug it into the socket with earth contact or unplug it again.
• Hold the mains adapter at the case when you pull it out of the socket with earth contact.
• Installation of a residual current circuit breaker with a rated release current of not more than 30 mA offers additional protection against electric shock.

Have the installation performed by a trained electrician only.

Use only the original mains adapter included with the device for mains operation.

• Connect the mains adapter only to an easily accessible socket with earth contact.
  • To avoid excessive heating, do not cover up the mains adapter
• Check the mains adapter and the hair/beard trimmer regularly for any mechanical defects.
• Replace any defective parts with an original part (specialist shop), but never attempt to repair a defective device yourself.
• Have repairs carried out only by a speciality retailer or by our Service Centre.
• Keep the hair/beard trimmer and mains adapter away from children, because children are not always able to judge hazards correctly.
• Make sure that the cable does not get caught in cupboard doors or pulled across hot surfaces.

Otherwise the cable insulation could be damaged.

Risk of electric shock!

To avoid injury, observe the following

• Never use the device with a defective comb attachment, because such an attachment could have sharp edges. There is a risk of injury
  To guarantee perfect operation
• Always operate the device only according to the information on the rating plate in order to allow optimal function.
• Do not subject the hair/beard trimmer to temperatures less than +10^ or greater than +40^ .
• Clean the device thoroughly after each use. • This device is not intended to be used by persons (including children) with restricted physical, sensory or mental capabilities or a lack of experience and/or lack of knowledge, unless they are supervised by a person responsible for safety or receive instructions from that person on how the device is to be used

BEFORE USE

The hair/beard trimmer can be used as a cordless or mains device.

Operation with the mains adapter:

First plug the mains adapter cable plug into the device, and then connect the mains adapter to the power supply system (230 V \~). A charging level display (CHARGE) lights up. The hair/ beard trimmer is ready for immediate use in mains operation.

CHARGING THE BATTERIES AND CORDLESS OPERATION:

- Make certain that the device is switched off.

Before the first use, you should charge the batteries of the hair/beard trimmer for a least 16 hours.

For subsequent charges, a charging time of approximately 8 hours is sufficient. Fully charged batteries allow cordless use for approximately 50 minutes.

• Place the device into the charging station.
• Plug the mains adapter cable into the connection on the back of the charging station.
• Connect the mains adapter to a suitable socket with earth contact (230 V \~).

The LED charging level indicators (CHARGE) on the device light, one after the other, and indicate the charging process.

The charging level display, which is equipped with light-emitting diodes (LEDs), is located on the front of the device. It shows the current charging status.

The LEDs light blue, one after the other, starting with 20%. The other LEDs also light constantly as soon as the respective charging level has been reached. When the rechargeable batteries have been fully charged, all LEDs light at the same time.

When only the lowest LED (20%) lights, you should charge the batteries fully again as soon as possible.

If you are using your hair/beard trimmer and it comes to a standstill because of low batteries, you can continue trimming by plugging it into the wall power supply. The hair/beard trimmer is equipped with two Ni-MH heavy duty rechargeable batteries with overcharge protection.

It can be recharged without power restrictions; there is no risk of an overcharge.

The rechargeable batteries in the hair/beard trimmer reach their optimal performance after they have been charged and discharged three times. Completely discharge the batteries before charging them again in order to guarantee a long battery life.

To completely discharge the device, run it until it comes to a complete standstill

OPERATION

Tip:

The hair that you want to trim should be clean and dry.

• Comb through the hair carefully to remove any tangles
• Lay a hairdressing cape or towel around the throat and neck in order to keep the cut hair from falling under the collar

CUTTING HAIR:

Tip: Begin with a longer attachment and trim the hair step by step to the desired length.

Cutting length attachments :

• Take the cutting length attachment that matches the desired length of the hair (4-6 mm / 10-12 mm / 16-18 mm / 22-24 mm / 28-30 mm).
- Insert the selected cutting length attachment on to the cutting unit from the back.
Make sure that both pins of the attachment snap into place correctly in the recesses at the side of the trimming head holder
• Always cut only small sections at one time
- Guide the hair/beard trimmer slowly through the hair
- When trimming, hold the device so that the selected cutting length attachment lies as flat at as possible
• Always cut from the neck towards the top of the head or from the forehead and temples up towards the middle of the head.

CUTTING WITHOUT ATTACHMENT:

Caution: The trimmer head is very sharp.

Risk of injury!

You can cut hair to a length between 0.8 mm and 2.8 mm if you do not use a cutting length attachment

For fi ne adjustment of the length, slide the setting to the desired length

Cutting contours at the hairline, neck and sideburns:

• Turn the device so that the back is pointing up
• Lay the edge of the cutting unit without cutting length attachment at the desired level of the hairline.
• Move the running hair/beard trimmer downwards.

To thin hair:

- To thin out the hair, insert the thinning attachment on the cutting unit in the same way you would a cutting length attachment.

This function reduces the volume of the hair.

CLEANING AND MAINTENANCE

DANGER

Risk of loss of life from electric shock!

• Pull the mains plug out of the socket with earth contact before you clean the device.
• Never hold the mains adapter with wet hands if you want to plug it into the socket with earth contact or unplug it again.
  • Always keep the mains adapter and connection line dry

WARNING:

Do not clean the hair/beard trimmer by immersing it in water or other liquids, because the device is not waterproof. Doing so could damage current-carrying parts (rechargeable batteries).

Cleaning the case:

Use a slightly moist cloth to clean the case.

Cleaning the hair/beard trimmer:

• Switch the hair/beard trimmer off.
• Disconnect the cable from the device and pull the mains adapter out of the socket with earth contact.
• Remove the cutting length attachment from the device.
• If necessary, wash the cutting length attachments off in running water
• Then dry the attachments thoroughly.

Press against the teeth of the trimmer head from above with your thumbs to remove the cutting unit from the holder.

• Use the cleaning brush that came with the trimmer to remove any remaining cut hairs from the cutting unit.
• When done cleaning, insert the locking clip of the cutting unit into the retaining opening of the trimmer head holder.
• Snap the cutting unit into place again by pressing lightly from the back.

Tip: To reduce friction, occasionally place one or two drops of cutter oil (included) between the blades and distribute it uniformly. You can also use any acid-tree oil (such as sewing machine oil). Wipe any excess oil off with a cloth.

POPIS

Six black hair comb icons arranged in two rows, labeled 5 and 6, 7 (no text or symbols on the comb itself)

BEZPEČNOSTNÍ OPATŘENÍ