AS 45 E - Snow blower ALPINA - Free user manual and instructions

Product type	Electric snow blower
Brand	Alpina
Model	AS 45 E
Power supply	Electric 230 V / 50 Hz
Motor	2000 W
Clearing width	45 cm
Maximum clearing height	25 cm
Maximum throwing distance	10 m
Bucket capacity	Without bucket (direct throw)
Wheels	2 drive wheels
Weight	22 kg
Dimensions (L x W x H)	90 x 55 x 60 cm
Noise level	85 dB(A)
Safety	Emergency stop, overload protection
Maintenance	Clean after each use, lubricate moving parts
Spare parts	Available from Alpina after-sales service
Warranty	2 years

Frequently Asked Questions - AS 45 E ALPINA

What is the clearing width of the Alpina AS 45 E?

The clearing width is 45 cm, ideal for driveways and sidewalks.

How to start the snow blower?

Plug in the power, ensure the switch is in the off position, then engage the safety lever and turn the start key.

What to do if the machine does not start?

Check the electrical connection, the condition of the cable and fuse. Ensure the chute is properly mounted and the safety lever is depressed.

How to adjust the throwing direction?

Use the orientation handle to direct the chute left or right; the deflector allows you to change the throwing angle.

How to clean the impeller after use?

Unplug the unit, remove remaining snow with a non-metallic brush, and wipe the impeller with a dry cloth.

What oil to use for the motor?

This model is electric and does not require motor oil. Only lubricate the mechanical parts with a light oil.

How to store the unit in summer?

Clean it thoroughly, dry it, then store it in a dry, frost-free place. Cover it to prevent dust.

What are the important safety instructions?

Never insert hands into the impeller, wear safety goggles and non-slip shoes, and unplug the unit before any maintenance.

Where to find spare parts?

Spare parts are available at authorized Alpina dealers or on the official website. Specify the model AS 45 E for an accurate order.

What is the motor power?

The electric motor has a power of 2000 W, sufficient for clearing moderate surfaces.

USER MANUAL AS 45 E ALPINA

Illustration of a snowman blade with handle and mounting bracket (no text or symbols)

AS 45 E

BRUKSANVISNING SV ..... 3

KÄYTTÖOHJEET FI...... 7

BRUGSANVISNING DA.....11

BRUKSANVISNING NO .....15

KASUTUSJUHISED ET.....60

NAUDOJIMO INSTRUKCIJOS LT ..... 64

LIETOŠANAS INSTRUKCIJA LV..... 68

1 ALLMÄNT

2.4 VEDLIKEHOLD OG OPPBEVARING

This symbol indicates WARNING. Serious personal injury and/or damage to property may result if the instructions are not followed carefully.

The following symbols appear on the machine. They are there to remind you of the care and attention required in use. This is what the symbols mean:

Warning. If the regulations are not followed, there is a risk of danger to life and machine breakdown.

Read the owner's manual before operating the machine.

Keep bystanders at a safe distance from the machine.

Warning of hard objects flying off.

The power supply must be disconnected before carrying out cleaning or maintenance. Shut off the motor before unclogging the discharge shute.

Keep hands and feet away from rotating parts. Risk of death and maiming. Avoid injury from the rotating auger, keep hands, feet and clothing away.

Risk of fatal electric shocks

1.1 REFERENCES

1.1.1 Figures

The figures in these instructions for use are numbered 1, 2, 3, etc.

Components shown in the figures are marked A, B, C, etc. A reference to component E in figure 5 is written "5:E".

1.1.2 Headings

The headings in these instructions for use are numbered in accordance with the following example:

“2.3.2” is a subheading to “2.3” and is included under this heading.

When referring to headings, only the number of the heading is normally specified. E.g. "Sec 2.3.2".

2 SAFETY INSTRUCTIONS

2.1 GENERAL

• Please read through these instructions carefully. Learn all the controls and the correct use of the machine.
• Never allow children or anyone who is not familiar with these instructions to use the snow thrower. Local regulations may impose restrictions as regards the age of the driver.
• Never use the machine if others, particularly children or animals, are in the vicinity.

• Remember that the driver is responsible for accidents that happen to other people or their property.

• Be careful not to trip or fall, especially when reversing the machine.

• Never use the snow thrower under the influence of alcohol or medication and if you are tired or ill.

2.2 PREPARATIONS

• Check the area to be cleared and remove any loose or foreign objects.
• Disengage all controls before starting the engine.
• Never use the snow thrower unless properly dressed. Wear footwear that improves your grip on a slippery surface.
• Adjust the height of the auger housing to ensure it stays above gravel paths.
• Check that the mains voltage corresponds with the snow thrower's rated voltage.
• Never, under any circumstances, make adjustments while the engine is running (unless otherwise specified in the instructions).
• Allow the snow thrower to adjust to the outdoor temperature before using it.
• Always use protective goggles or a visor during use, maintenance and service.

2.3 OPERATION

- Keep hands and feet away from rotating parts. Always avoid the discharge chute opening.

- The snow thrower must never be used to remove anything but snow

- Be careful when driving on or crossing gravel paths, pavements and roads. Be aware of hidden dangers and traffic.

- Never direct the discharge chute towards a public road or traffic.

- If the snow thrower hits a foreign object, stop the engine, disconnect and carefully inspect the machine for damage. Repair the damage before using the machine again.

- If the machine starts vibrating abnormally, stop the engine and look for the cause. Vibration is normally a sign of something wrong.

- The snow thrower may only be connected to power sockets that are supplied with earth leakage circuit breakers. The earth leakage circuit breaker must have a trip current of max. 30 mA.

- Risk of tripping over the electric cable. Always be aware of the whereabouts of the electric cable so that it does not get in the way of your feet or anything else moving about in the area.

- The snow thrower may only be connected with a cable that is approved for outdoor use.

- The electric cable with which the snow thrower is connected must always be intact. It must never be used if it displays signs of damage.

- The snow thrower must never be used if its plug, electric cable or other electrical equipment is damaged.

- Repairs to the electrical equipment may only be carried out by an authorised electrician.

- Never drive over the electric cable for the snow thrower while working.

- If the electric cable for the snow thrower has been damaged while working, the following instructions must be followed:

A. Stop the motor.
B. Leave the site in the opposite direction from the damaged point on the cable.
C. Disconnect the cable from the power socket.

- Stop the motor and disconnect the power supply:

A. If the driver leaves the machine.
B. If the auger housing or discharge chute is blocked and must be cleaned.
C. Before beginning repairs or adjustments.

• Always make sure the rotating parts have stopped and all the controls are disengaged before cleaning, repairing or inspection.
- Never drive across a slope. Move from the top down, and from the bottom to the top. Be careful when changing direction on a slope. Avoid steep slopes.
- Never operate the machine with insufficient protection or without the safety devices in place.
- Existing safety devices must not be disconnected or disengaged.
- Never use the snow thrower near enclosures, cars, windowpanes, slopes etc. without properly setting the discharge chute deflector.
• Always keep children away from areas to be cleared. Get another adult to keep the children under supervision.
- Do not overload the machine by driving it too fast.
• Take care when reversing. Look behind you before and during reversing to check for any obstacles.
- Never point the discharge chute towards bystanders. Do not allow anyone to stand in front of the machine.
- Disengage the auger when the snow thrower is to be transported or is not in use Do not drive too fast on slippery surfaces when transporting.
- Only use accessories that are approved by the machine's manufacturer.
- Never drive the snow thrower in bad visibility or without satisfactory lighting.
• Always ensure you have a good balance and a tight grip on the handle.

2.4 MAINTENANCE AND STORAGE

• Tighten all nuts and screws so that the machine is in safe working condition.
• Never flush the machine with water. It will make damage to the electrical equipment and risk of electrical shocks.
• Check all electrical equipment before use. The snow thrower must never be used if its insulatings, fittings or other electrical equipment is damaged.
  • Always use genuine spare parts. Non-genuine spare parts can entail a risk of injury, even if they fit the machine.
• Before a long storage, check the instructions for recommendations.
• Replace damaged warning and instruction stickers.
• Let the engine run a couple of minutes with the auger connected after use. This prevents the auger from freezing solid.

3 ASSEMBLY

3.1 UNPACKING

1. Open the box carefully.
2. Take care of any documentation in the box, for example these instructions.
3. Lift the snow thrower from the box.
4. Cut the tie straps holding the chute control shaft to the side of the handle.
5. Dispose of the box and packaging according to local regulations.

3.2 HANDLE

1. Unfold the handle.
2. Tighten the four knobs (1:D).
3. Secure the cable to the handle with two clamps (1:C).

3.3 CHUTE CONTROL

1. Place the shaft through the loop on the handle (2:L).
2. Insert the shaft in the joint (2:M). Make sure the holes in the shaft and the joint are aligned.
3. Lock the shaft by tightening the screw (3:N) all the way through the shaft and joint.
4. Check the discharge chute by turning it fully in both directions. The chute should rotate freely.

4 CONTROLS

The snow thrower is fitted with the following controls and devices.

Starting handle (1:A) – Starts and stops the electric motor. Ignition lock (1:K) – Facilitates activation of the starting handle.

Connector (1:J) - For electrical connection.

Cable support (1:B) – For supporting the connection cable.

Deflector lock (1:E) – Locks the deflector in position.

Chute control lever (1:F)—Changes the direction of the discharge chute.

Discharge chute (1:H) – Ejects the snow.

Deflector (1:I) - Determines the distance the snow is thrown.

5 USING THE MACHINE

5.1 GENERAL

Never start the engine until all the above measures under 'ASSEMBLY' have been carried out.

Never use the snow thrower without first reading and understanding the enclosed instructions and all the warning and instruction stickers on the snow thrower and in these instructions.

Always wear protective goggles or a visor during use, maintenance and service.

5.2 BEFORE STARTING

The connection cable and its plugs must be fault free and approved for outdoor use.

The connection cable may only be connected to power sockets equipped with an earth leakage circuit breaker with a trip current of max. 30 mA.

The connection cable must be suspended on the cable support. Otherwise there is a risk of damage alongside the plug which is potentially life-threatening.

Connect the snow thrower with the electric cable from the property's power socket.

Suspend the cable on the cable support (1:B) and connect to the connector (1:J).

5.3 START

Start the motor and the auger as described below.

1. Lean the snow thrower back slightly so that the auger is raised a little above the ground.
2. Press in and hold the button (1:K). Squeeze the handle (1:A).
3. Release the ignition lock, lower the auger towards the ground and start to clear the snow.

5.4 SAFETY TEST

After starting and before use of the machine, it is essential to perform the safety test below.

If the unit fails to operate as described, DO NOT operate it. In this case, contact an authorised workshop for repair.

Auger test

Release the starting handle. The motor and the auger should stop immediately

5.5 STOP

Stop the motor and the auger by releasing the starting handle (1:A).

5.6 SNOW CLEARANCE

See fig. 1.

Never aim the snow at bystanders.

Always stop the engine before unclogging.

Always wear eye protection when operating the snow thrower.

If the auger is blocked, never try to keep the motor engaged for more than 20 seconds. Extensive engagement will damage the motor.

1. Start the motor as described above and check the ejection distance and direction.
2. If necessary, stop the motor and adjust the deflector (1:I). Upwards gives a longer throwing distance and downwards gives a shorter throwing distance. Lock the deflector in position using the knob (1:E).
3. If necessary, stop the motor and adjust the discharge chute (1:H) with the lever (1:F) so that the snow is ejected in the desired direction.
4. Stop working by releasing the starting handle (1:A).

The snow thrower is propelled automatically with the aid of the auger. To facilitate propulsion, raise the handlebar a little. Do not push the snow thrower.

5.7 OPERATING TIPS

1. Clear away the snow immediately after snowfall.
2. For complete snow clearance, slightly overlap each clearance pass.
3. If possible, discharge the snow downwind.
4. In strong wind, lower the deflector to direct the discharged snow close to the ground, where it is less likely to blow into unwanted areas.
5. For safety and to prevent damage to the snow thrower, keep the area to be cleared free of stones, toys and other foreign objects.
6. The snow thrower's capacity depends on the depth and density of the snow. Learn how the snow thrower works in different snow conditions.

5.7.1 Dry and normal snow

Snow up to 20 cm deep can be removed quickly and easily by clearing at an even speed. Plan for downwind discharge of the snow.

5.7.2 Wet, packed snow

Drive slowly forward. Avoid to use the scraping blade to remove remaining packen snow and ice. Hoeing will lead to fatigue failure in the auger housing.

5.8 AFTER USE

The snow thrower must never be rinsed with water. Risk of damage to the electrical system and risk of electric shocks.

1. Stop the motor.
2. Disconnect the electric cable from the snow thrower and the property's power socket.
3. Allow the snow thrower to cool for 30 minutes.
4. Clean the inside and outside of the snow thrower with a suitable brush.
5. Check that there are no damaged or loose parts. Repair/replace parts if necessary.

6 MAINTENANCE

The electrical connection must be disconnected before carrying out maintenance work.

6.1 BEFORE USE

• Every time the snow thrower is to be used, check that the electrical equipment is intact and free of faults. The snow thrower must not be used if there are any faults or if anything is missing.
• Check that the auger rotates easily.
• Check that all screw joints are tightened. Tighten if necessary.
• Apply silicon spray to the auger. This prevents icing.
• Check that the starting handle cannot be activated without the ignition lock being moved to the left.

6.2 FAULT-TRACING

The faults described below can usually be rectified directly by the user. If there is any doubt, contact an authorised agent.

The motor does not start:

• The electric cable is not connected or is defective.
- The fuse has blown. If a higher amp fuse needs to be installed, contact an authorised electrician.

The motor hums, but does not start:

- Auger or discharge chute blocked.

• The capacitor is defective. Contact your GGP agent.

The motor stops suddenly:

- Loose plugs.

• The overload protection has been tripped. Wait for 10 minutes, then attempt to start again.

The snow thrower vibrates:

• Loose parts.
• Defective auger.
  • The motor is loose.
  The snow thrower does not clear any snow:
• Auger or discharge chute blocked.
  The drive belt is loose or defective.

7 STORAGE

When the snow thrower is to be stored for an extended period, such as during that part of the year when snow clearance does not need to be carried out, the following measures must be taken.

1. Clean the whole snow thrower thoroughly.
2. Inspect the snow thrower for damage. Repair if necessary.
3. Touch up any paint damage.
4. Rust-proof unpainted metal surfaces.
5. Store the snow thrower in a clean, dry place.

8 PURCHASE TERMS

A full warranty is issued against manufacturing and material defects. The user must carefully follow the instructions given in the enclosed documentation.

The warranty does not cover damage due to:

• Neglect by users to acquaint themselves with accompanying documentation
• Carelessness
• Incorrect and non-permitted use or assembly
• The use of non-genuine spare parts
• The use of accessories not supplied or approved by GGP Neither does the warranty cover:
• Wear parts such as drive belts, augers, wheels
• Normal wear
• Engines. These are covered by the engine manufacturer's warranties, with separate terms and conditions.

The purchaser is covered by the national laws of each country. The rights to which the purchaser is entitled with the support of these laws are not restricted by this warranty.

1 GÉNÉRALITÉS

8 SMLUVNÍ PODMÍNKY PRODEJE

Figyelmeztetés.