BE 1300-X3 Quick - Drill METABO - Free user manual and instructions

Product Type	Impact Drill
Brand	Metabo
Model	BE 1300-X3 Quick
Rated Power	1300 W
Supply Voltage	230 V ~ 50 Hz
No-load Speed	0 – 3000 rpm
Chuck	Self-tightening Chuck (Quick)
Chuck Capacity	1.5 – 13 mm
Max Drilling Diameter (steel)	13 mm
Max Drilling Diameter (wood)	40 mm
Max Drilling Diameter (concrete)	20 mm
Hammer Function	Yes
Speed Variator	Electronic
Direction of Rotation	Reversible (left/right)
Shaft Lock	Yes
Weight	2.4 kg
Cable Length	4 m
Dimensions (L x W x H)	360 x 100 x 250 mm
Protection Class	II (double insulation)
Maintenance	Clean ventilation slots regularly; periodic lubrication of the chuck
Safety Instructions	Wear hearing and eye protection; use dust extraction when necessary
Spare Parts	Available at service.metabo.com

Frequently Asked Questions - BE 1300-X3 Quick METABO

How to change the chuck on the Metabo BE 1300-X3 Quick?

The Quick chuck is unscrewed by hand after locking the shaft. Turn the chuck ring counterclockwise to remove it. To install a new bit, insert it and tighten by hand.

Why is the drill no longer turning?

First check the power cord and fuse. If the tool does not start, the brushes may be worn. Replace them with original Metabo parts.

What power for the Metabo BE 1300-X3 Quick?

This model develops a power of 1300 W, ideal for intensive drilling in wood, metal, and concrete.

How to use the hammer function?

To activate the hammer function, turn the selector located above the chuck to the hammer symbol. Use this function for drilling into masonry or concrete.

What is the maximum drilling diameter?

Maximum diameters are: 40 mm in wood, 13 mm in steel, and 20 mm in concrete with hammer action.

How to reverse the direction of rotation?

Use the direction switch located near the trigger. Push it left for forward rotation (drilling) and right for reverse rotation (screwing).

What type of grease to use for the chuck?

Use a special grease for self-tightening chucks, available from Metabo. Apply a small amount every 6 months.

How to adjust the speed?

The speed is electronically adjustable by pressing the trigger more or less. A variator allows progressive control from 0 to 3000 rpm.

What to do if the drill smokes or smells burnt?

Immediately stop the tool and unplug it. This may indicate a motor blockage or worn brushes. Consult an authorized Metabo after-sales service.

Where to find spare parts for the BE 1300-X3 Quick?

Original spare parts are available on the website service.metabo.com or from authorized Metabo dealers.

USER MANUAL BE 1300-X3 Quick METABO

Three Metabo electric drillers displayed against a plain background (no text or symbols visible on the machines themselves)

Original instructions

1. Declaration of Conformity

We, being solely responsible, hereby declare that these drills, identified by type and serial number *1), meet all relevant requirements of directives *2) and standards *3). Technical documents for *4) - see page 3.

2. Specified Use

The drill is suitable for non-impact drilling into metal, wood, plastic and similar materials. It is also suitable for thread tapping and screwdriving.

The user bears sole responsibility for any damage caused by improper use.

Generally accepted accident prevention regulations and the enclosed safety information must be observed.

3. General Safety Instructions

For your own protection and for the protection of your electrical tool, pay attention to all parts of the text that are marked with this symbol!

WARNING – Reading the operating instructions will reduce the risk of injury.

WARNING Read all safety warnings and instructions. Failure to follow all safety warn-

ings and instructions may result in electric shock, fire and/or serious injury.

Keep all safety instructions and information for future reference.

Pass on your electrical tool only together with these documents.

4. Special Safety Instructions

Use the additional handle supplied with the tool. Loss of control can cause personal injury.

Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

Pull the plug out of the plug socket before any adjustments or servicing are performed.

Avoid inadvertent starts by always unlocking the switch when the plug is removed from the mains socket or in case of a power cut.

Ensure that the spot where you wish to work is free of power cables, gas lines or water pipes (e.g. using a metal detector).

Smaller workpieces must be secured such that they are not carried along with the drill bit when drilling

(e.g. by clamping in a vice or on a work bench with screw clamps).

Keep hands away from the rotating tool! Remove chips and similar material only when the machine is not in operation.

Metabo S-automatic safety clutch. When the safety clutch responds, switch off the machine immediately! If the tool jams or catches, the power supply to the motor is restricted. Due to the strong force which can arise, always hold the machine with both hands using the handles provided, stand securely and concentrate.

The Metabo S-automatic safety clutch must not be used for torque control.

Caution must be exercised when driving screws into hard materials (driving screws with metric or imperial threads into steel)! The screw head may break, or a high reverse torque may build up on the handle.

Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders.

Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists.

- Where the use of a dust extraction device is possible it shall be used.

- The work place must be well ventilated.

- The use of a dust mask of filter class P2 is recommended.

Follow national requirements for the materials you want to work with.

5. Overview

See page 2.

1 Thumbwheel for gear selection
2 Additional handle / Additional handle with vibration damping *
3 G e a r e d c h u c k *
4 Futuro Plus keyless chuck *
5 Speed preselection setting wheel*
6 Electronic signal indicator*
7 Rotation selector switch
8 Locking button for continuous a ctivation
9 Triggers switch

* depending on equipment

6. Initial Operation

Before plugging in, check that the rated mains voltage and mains frequency, as stated on the rating label, match with your power supply.

To ensure that the drill chuck is securely fitted: After initial drilling (clockwise), use a

ENGLISHen

screwdriver to firmly tighten the safety screw inside the drill chuck (if applicable / model-specific). Caution left-handed thread! (see Section 8.7.)

6.1 Assembly of additional handle (2)

For safety reasons, always use the additional handle supplied.

Open the clamping ring by turning the additional handle (2) counter-clockwise. Push the additional handle onto the collar of the machine. Slide the additional handle far enough forward so that it can be turned. At the desired angle, pull it back and tighten firmly.

7. Use

7.1 Setting direction of rotation, transport lock (switch-on lock)

Do not activate the rotation selector switch (7) unless the motor has completely stopped.

See page 2.

R = Clockwise setting
L = Counter-clockwise setting
0 = Central position: transport lock setting (switch-on lock)

The drill chuck must be firmly screwed onto the spindle and the safety screw inside the drill chuck (if applicable / model-specific) must be firmly tightened with a screwdriver. (Caution, left-handed thread!) If rotated counterclockwise (e.g. when screwing) it could otherwise become loose.

7.2 Selecting a gear

Select the desired gear by turning the thumbwheel (1).

Change speed only when the machine is in the process of running down (briefly switch it on and off).

1st gear (low speed, high torque) e.g. for screwdriving, drilling

2nd gear (high speed) e.g. for drilling

7.3 Preselect speed

Use the setting wheel (5) to preselect the maximum speed. See page 4 for recommended drilling speeds.

7.4 Switching on/off, changing speed

Switching on, speed: press the trigger (9).

The speed can be changed by pressing in the trigger.

The electronic soft start means that the machine accelerates continuously until the preselected speed is reached.

Release the trigger to switch off.

Continuous activation: While pressing on the trigger (9), press in the locking button (8) and then release the trigger. To switch off, press and release the trigger (9) again.

In continuous operation, the machine continues running if it is forced out of your hands. Therefore, always hold the machine with both hands using the handles provided, stand in a safe position and concentrate.

7.5 Tool change with Plus (4) chuck

See illustrations A, page 2.

Opening the drill chuck:

Using one hand, hold the retaining ring securely (depending on equipment, not necessary for BE 1300 Quick) and, using the other hand, turn the sleeve in the direction of the arrow -1.

The ratchet sound which can possibly be heard after opening the drill chuck is functional and is switched off by a reverse rotation of the sleeve.

BE 751, BE 1100: If the chuck is very securely tightened: Unplug. Hold the chuck using an open-end spanner at the flats on its head, and turn the sleeve vigorously in the direction of the arrow -1.

Clamping the tool

• Insert the tool -2- as far as possible.
• Using one hand, hold the retainer ring securely (depending on equipment; not required for BE 1300 Quick).
• Turn sleeve in direction -3- until the noticeable mechanical resistance has been overcome.
• Caut ion! The tool is not yet fully tightened! Keep turning the sleeve (it must "click" when turning) until it cannot be turned any further - only now is the tool safely clamped.

With a soft tool shank, retightening may be required after a short period of operation.

7.6 Tool change with a geared chuck (3)

See illustrations B on page 2.

Opening the drill chuck: Open the geared chuck with chuck key -1.

Clamping the tool: Insert tool -2- as far as possible and, using the chuck key, evenly secure in all 3 bores -3.

7.7 Drill chuck with "Quick" change system (for BE 1300 Quick)

See illustration on page 2.

To remove: Push the interlock ring forward (a), advance and pull off the chuck (b).

To mount: Push the interlock ring forward and move the chuck as far as the limit stop on the drill spindle (slightly turn the chuck if necessary).

7.8 Unscrewing chuck (when screwing without chuck or when using attachments)

See illustrations Y, Z on the second last page.

Note for illus. Y, Z: Release by tapping lightly with a rubber hammer, as shown, and unscrew.

Note: If a bit clamping bush (order no. 6.31281) is attached, the screwdriver bit inserted in the hexagon socket of the spindle is held in place.

8. Cleaning, Maintenance

Cleaning the keyless chuck:

After prolonged use hold the chuck vertically, with the opening facing down, and fully open and close it several times. The dust collected falls from the opening. Regular use of cleaning spray on the jaws and jaw openings is recommended.

9. Troubleshooting

Electronic signal display (6) (BE 1100, BE 1300 Quick)

Rapid flashing - restart protection

When power is restored after a power failure, the machine - which is still switched on - will not start by itself for safety reasons. Switch machine on and off again.

Slow flashing - carbon brushes worn

The carbon brushes are almost completely worn. If the brushes are completely worn, the machine switches off automatically. Have the brushes replaced by an authorised service centre.

Permanently lit - overload

If the machine is subject to continuous overloading for longer periods, the power input to the machine is limited. This prevents additional unauthorised heating of the motor.

10. Accessories

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements and specifications listed in these operating instructions.

Fit accessories securely. Secure the machine if it is operated in a bracket. Loss of control can cause personal injury.

For a complete range of accessories, see www.metabo.com or the main catalogue.

11. Repairs

Repairs to electrical tools must be carried out by qualified electricians ONLY!

If you have Metabo electrical tools that require repairs, please contact your Metabo service centre. For addresses see www.metabo.com.

You can download spare parts lists from www.metabo.com.

12. Environmental Protection

Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories.

Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Guideline 2002/

96/EC on used electronic and electric equipment and its implementation in national legal systems,

used power tools must be collected separately and handed in for environmentally compatible recycling.

13. Technical Specifications

Explanatory notes on the information on page 3.

Changes due to technological progress reserved.

$$ P _ {1} = \text { Rated input } $$

$$ P _ {2} \quad = \text { Power output } $$

$$ n _ {1} ^ {*} = \text { No - load speed } $$

$$ n _ {2} ^ {*} \quad = \quad L \quad o \quad a \quad d \quad s \quad p \quad e \quad e $$

$$ \varnothing \max = \text { Max. drill diameter } $$

$$ b = \text { Chuck capacity } $$

$$ G = \text { Drill spindle thread } $$

$$ H = \text { Drill spindle with hexagon socket } $$

$$ m = W e i g h t $$

$$ D = \text { Collar diameter } $$

Measured values determined in conformity with EN 60745.

□ Machine in protection class II

\~ Alternating current

The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).

* Energy-rich, high-frequency interference can cause fluctuations in speed. The fluctuations disappear, however, as soon as the interference fades away.

Emission values Using these values

Using these values, you can estimate the emissions from this power tool and compare these with the values emitted by other power tools. The actual values may be higher or lower, depending on the particular application and the condition of the tool or power tool. In estimating the values, you should also include work breaks and periods of low use. Based on the estimated emission values, specify protective measures for the user - for example, any organisational steps that must be put in place.

Vibration total value (vector sum of three directions) determined in accordance with EN 60745:

$$ a _ {h, D} = \text { Vibration emission value } $$

$$ (d r i l l i n g \text { into metal }) $$

$$ K _ {h, D} = \text { Uncertainty (vibration) } $$

Typical A-effective perceived sound levels:

$$ L _ {p A} = \text { Sound pressure level } $$

$$ L _ {W A} = \text { Acoustic power level } $$

$$ K _ {D A}, K _ {W A} = \text { Uncertainty } $$

Wear ear protectors!

Wear ear protectors!

FRANÇAISfr

Notice originale

Allumage permanent - surcharge

$$ a _ {h, D} = \text { trillingsemissiewaarde (boren in metaal) } $$

$$ K _ {h, D} = \text { onzekerheid (trilling) } $$

a_{h, D} = Vibrationsemissionsvärde (borrning i metall)

K_h,D = onoggrannhet (vibrationer)

Normal, A-viktad ljudnivå:

L_pA =äänenpainetaso

L_WA =äänentehotaso

a_h,D =Vibrationsemission (boring i metal) K_h,D =Usikkerhed (vibration)

Close-up of a drill bit being inserted into a mechanical component, showing tip and threaded shaft (no text or symbols)

Close-up of a hand using a tool to adjust a mechanical component, showing a curved arrow indicating rotation (no text or symbols present)

Close-up of a drill bit being inserted into a mechanical component (no text or symbols visible)

Close-up of a hand using a mechanical drill bit to adjust a workpiece (no text or symbols visible)