GRAEF CM 81 - Coffee grinder

CM 81 - Coffee grinder GRAEF - Free user manual and instructions

Find the device manual for free CM 81 GRAEF in PDF.

📄 84 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice GRAEF CM 81 - page 17
Pick your language and provide your email: we'll send you a specifically translated version.
Product typeConical burr coffee grinder
BrandGraef
ModelCM 81
Dimensions (W x D x H)Approximately 12 x 18 x 35 cm
WeightApproximately 1.5 kg
Power supply230 V, 50 Hz, 110 W
Bean hopper capacityApproximately 200 g
Ground coffee container capacityApproximately 100 g
Grind adjustment30 fineness levels
Burr typeConical steel burrs
Auto shut-off functionYes, timer or manual stop
Anti-staticYes, to prevent splatters
CleaningRemovable burrs for easy cleaning
MaintenanceBrush the burrs regularly
SafetySafety lock if hopper is incorrectly positioned
Spare parts availableConical burrs, containers
RepairabilityHigh repairability score (standard parts)

Frequently Asked Questions - CM 81 GRAEF

How to adjust the grind fineness on the Graef CM 81?
Turn the adjustment knob located on top of the device. The 30 notches allow you to go from the finest grind (for espresso) to the coarsest (for filter coffee).
How to clean the Graef CM 81 coffee grinder?
Unplug the device. Remove the bean hopper and the ground coffee container. Brush the conical burrs with the provided brush. Never wash the burrs with water. Use a damp cloth for the exterior.
Can I grind espresso beans with the Graef CM 81?
Yes, thanks to its conical steel burrs and precise adjustment, you can achieve a very fine grind suitable for espresso.
Is the Graef CM 81 noisy?
Like most burr grinders, it produces moderate noise during grinding, but remains acceptable for domestic use.
How long does it take to grind a dose of coffee?
The grinding time depends on the dose and fineness. For 18 g of beans at a fine grind, count about 15 to 20 seconds.
How to prevent the grind from sticking to the walls?
The Graef CM 81 is equipped with an anti-static system that reduces static electricity. Make sure the container is clean and dry.
Can I use flavored or oily beans?
It is not recommended to use very oily or flavored beans as they can clog the burrs and alter the taste. Use natural roasted coffee beans.
What to do if the grinder stops working?
Check that the bean hopper and container are properly engaged. Also check that the timer is not set to 0. If the problem persists, contact Graef customer service.
Is the Graef CM 81 under warranty?
Yes, the manufacturer's warranty is 2 years. Keep the purchase receipt and manual for any claims.
Where to find spare parts for the Graef CM 81?
You can order conical burrs and containers from Graef customer service or on approved spare parts websites.

User questions about CM 81 GRAEF

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Coffee grinder in PDF format for free! Find your manual CM 81 - GRAEF and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CM 81 by GRAEF.

USER MANUAL CM 81 GRAEF

Bedienungsanleitung Operating Instructions Notice d'utilisation Manual de instrucciones Istruzioni per l'uso Bedieningshandleiding

DBedienungsanleitung3
ENOperating Instructions17
FNotice d’utilisation29
ESManual de Instrucciones42
IIstruzioni per l'uso55
NLBedieningshandleiding69

Vorwort

Simple line drawing of a curved mechanical part with a labeled number 8 (no text or symbols on the part itself)

Simple line drawing of a tool or plunger with a handle and lined tip (no text or symbols)

Technische Daten

WICHTIG!

D

HINWEIS

HINWEIS

You made the right decision with the purchase of the CM 80 / CM 81 coffee grinder. You have acquired an established quality product.

We thank you for your purchase and wish you lots of joy with your new coffee grinder.

more information or if you have any problems not covered or not sufficiently dealt with in these instructions, please contact the GRAEF customer service department or your dealer.

Warnings

The following warnings and signal words are used in these operating instructions:

Information about these operating instructions

These operating instructions are a component of the coffee grinder (in the following referred to as the unit) and provide important information about its first use, safety, the intended use and care of the unit.

The operating instructions must always be kept available near the unit. Every person who deals with the following must read and apply them:

  • First use,
  • Operation,
    • Repairing faults and/or
  • Cleaning

Keep the operating instructions and pass them on to the next owner together with the unit.

These operating instructions cannot cover every possible use. For

GRAEF CM 81 - Information about these operating instructions - 1

WARNING

That indicates a possibly dangerous situation. If the instructions are not complied with, severe injury can result or non-compliance can even lead to death.

CAUTION

That indicates a possibly dangerous situation. Non-compliance with the instruction can lead to property damage.

IMPORTANT!

This indicates useful tips and other important information!

Use as intended

This unit is not intended for commercial usage. Use the coffee grinder solely in closed rooms for grinding coffee beans.

This unit is intended to be used in household and similar applications such as:

- staff kitchen areas in shops, of-

EN

fices and other working environments;

  • farm houses;
  • by clients in hotels, motels and other residential type environments;
  • bed and breakfast type environments.

Any other use or use beyond and above that is considered non-in-tended usage.

CAUTION

Danger through non-intended usage!

The unit can cause hazards if used other than intended and/or for alien usage.

▶ Use the unit exclusively as intended.
▶ Follow the procedures described in these operating instructions.

All claims of any type due to non-intended usage are excluded.

The risk is borne solely by the operator.

Limitation of liability

All technical information, data and instructions for installation, operation and care included in these operating instructions accord with the latest state at the time of printing and have been made to the best of our knowledge with consideration of our previous experiences and insights.

No claims can be derived from the information, illustrations and descriptions in these instructions.

The manufacturer does not assume any liability for damages due to:

• Non-compliance with the instructions
• Non-intended use
- Improper repairs
• Technical modifications
• Use of non-approved spare parts

Translations are made in good faith. We do not assume any liability for translation errors. Solely the original German text is binding.

Customer service department

If your Graef unit becomes damaged, please contact your dealer or the Graef customer service department.

Gebr. Graef GmbH & Co. KG Customer service department Donnerfeld 6 59757 Arnsberg Germany

Tel.: + 49 (0) 2932 - 9703-6041

Fax: + 49 (0) 2932 - 9703-0

Email: service@graef.de

Safety

This chapter provides you with important safety instructions for handling the unit.

This unit complies with the statutory safety regulations. Improper use can, however, lead to personal injury and property damage.

Danger due to electric current

GRAEF CM 81 - Danger due to electric current - 1

WARNING

Danger to life due to electric current!

Touching live lines or components is mortally dangerous!

Follow the safety instructions below to prevent hazards from electric current:

▶ Do not use the unit if the power cord or plug are damaged.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified persons in order to avoid a hazard.
▶ Never open the unit housing under any circumstances. If live connections are touched and the electrical or mechanical structure changes, there is a danger of electric shock.
▶ Never touch any parts that are conducting electricity. They can cause an electric shock or even lead to death.

Basic safety instructions

To handle the unit safely, follow the instructions below:

  • Check the unit for external, visible damage to the housing, the supply cord and the plug before using it. Do not put a damaged unit into operation.
    ■ Repairs are only allowed to be performed by a specialist or by the GRAEF customer service department. Improper repairs can lead to extreme hazards for the user. Furthermore, the warranty claim expires.
    ■ Only GRAEF customer service is authorised to repair the unit during the warranty period, otherwise there the warranty expires for additional damages.
    ■ Defective components must be replaced solely with genuine spare parts. Fulfilment of the safety regulations is only guaranteed if these parts are used.
    This unit is not intended for use by people (including children) with restricted physical, sensory or mental capabilities, or who have a lack of experience and/or lack of knowledge, unless they are supervised by a person responsible for their safety or have received instructions from that person about how to use the unit.
    ■ Children should be supervised to ensure that they do not play with the unit.

EN

■ Always pull the supply line from the electric socket using the connector plug, not on the supply cord.
- Do not carry the unit by the supply cord.
■ Never transport the unit during operation.
■ The unit is not intended to be used with an external timer or a separate telecontrol system.
■ The unit is suitable solely for grinding coffee beans.
■ Do not touch the plug with moist hands.

First use

Safety instructions

CAUTION

Personal harm or property damage could occur when the unit is being used for the first time!

Follow the safety instructions below to prevent hazards:

▶ Do not use the packing material as a toy. Danger of suffocation.
▶ Follow the instructions regarding the requirements for the place of installation and on the unit's electrical connection to prevent personal harm and property damage.

Scope of delivery and shipping inspection

The unit comes standard with the following components:

  • Coffee grinder
    • Coffee bean container
  • Coffee container
    • Small group handle bracket
    • Large group handle bracket
  • Cleaning brush
  • Hose
  • Operating instructions

IMPORTANT!

▶ Check the delivery for completeness and for visible damage.
▶ Immediately notify the carrier, insurance company and the supplier about an incomplete delivery or damages due to improper packing or caused by shipping.

Unpacking

To unpack the unit, proceed as below:

Take the unit out of the carton.
◆ Remove all pieces of the packing.
◆ Remove any possibly extant labels on the coffee grinder (do not remove the rating plate).

GRAEF CM 81 - Unpacking - 1

Dispose of the packing

The packing protects the unit from shipping damage. The packing materials are selected for their environmental compatibility and from disposal aspects so they are recyclable.

Returning the packing to the materials circuit saves raw materials and reduces the accumulation of waste. Dispose of packing material that is no longer needed at a collection point for the »Green Point« recycling system.

IMPORTANT!

▶ If possible, save the original packing during the unit's warranty period to be able to properly pack the unit in case of a warranty claim.

Requirements for the in- stallation location

For safe and flawless operation of the unit, the place of location must meet these prerequisites:

■ The unit must be set up on a firm, flat, level, non-slip and heat resistant base that has sufficient load bearing capacity.
■ Select the place of location so that children cannot reach the hot surfaces of the unit.

■ The unit is not intended for installation in a wall or a built-in cupboard.

■ Do not set up the unit in a hot, wet or moist environment.
■ The electric socket must be readily accessible so that the power cord can be easily unplugged.

Electric connection

Follow these instructions about the electrical connection for safe and flawless operation of the unit:

■ Before connecting the unit, compare the connection information (voltage and frequency) on the rating plate with those of your electrical network. This information must match to avoid damage to the unit. If in doubt, ask your electrician.
■ The socket must be fused with at least a 10A circuit breaker.
■ Make sure that the power cord is not damaged. Do not conduct it over hot surfaces or sharp edges.
■ The supply cord must not be pulled tight.
■ The electrical safety of the unit is only ensured if it is connected to a properly installed protective conductor system. Operation on a socket without a protective conductor is prohibited. If in doubt, have the building installation checked by an electrician. The manufacturer does not assume any responsibility for damages caused by a missing or interrupted protective conductor.

EN

Before the first use

Clean all parts as described in "Cleaning and Care".

Setup and Functioning

Overview

1) Coffee bean container
2) Latching ring /Grind setting
3) Coffee container (The max scale mark 96 g)
4) Rubber base
5) On/off switch and automatic function
6) Hose
7) Large group handle bracket
8) Small group handle bracket
9) Cleaning brush

5 GRATE

7
Simple line drawing of a curved mechanical component or bracket (no text or symbols)

8
Simple line drawing of a curved mechanical component or bracket (no text or symbols)

Line drawing of a tool with a handle and segmented blade (no text or symbols)

Technical information

Dimensions (L x W x H) 23 x 13.5 x 38.5 cm

Weight ca. 2,5 kg

Operating voltage 220 - 240 V

Power consumption 120 - 150 W

Features

  • Coffee grinder
  • Aluminium housing
  • On/off switch with automatic function
  • Grind setting 1 - 24
  • Conical grinder
    • Coffee bean container
  • Coffee container
    • Small group handle bracket
    • Large group handle bracket
  • Rubber base
  • Cable rewind
  • Cleaning brush

Spare parts

The following spare parts can be supplied for this unit:

  • Replacement coffee bean container
    • Replacement coffee container
  • Replacement group handle bracket (small / large)
  • Replacement hose

Contact customer service if you need spare parts for your unit.

Control and operation

This chapter provides you with important information on controlling and operating the unit.

Safety instructions

CAUTION

Follow the safety instructions below to prevent hazards and property damage:

▶ Never put your hands, hair, clothing or other foreign bodies in the bean grinder while the unit is in operation.
▶ Do not try to regrind previously ground coffee.

Grind setting / Operating times

You can influence the composition of the coffee with various grind settings.

Setting
10 - 15 Espressoso coffee
20 - 23 Filter coffee

The wide range of grind settings lets you make a precise adjustment.

Please observe the instructions below when using the coffee grinder.

◆ The finer the grind, the longer the grinding process takes.
If you use a fine grind level, it is possible that the coffee sticks together. During grinding, knock on the coffee bean container cover so that any possible coffee

bean clumps do not block the grinding.

EN

Grinding coffee

◆ Plug the plug into the electric socket.
◆ Fill the coffee bean container with coffee beans.

IMPORTANT!

▶ Always only use whole coffee beans.
▶ Fill the coffee bean container evenly with coffee beans. Uniform weight is important to ensure smooth grinding.

Take off the cover of the coffee container and set it on the base between the group handle bracket.

◆ Set the switch to "ON"

Line drawing of a hand using a blender to press a cup (no text or symbols)

◆ Set the desired grind level.

Illustration of a hand holding a cylindrical device with red arrows indicating motion or force direction (no text or symbols)

◆ The coffee flows into the coffee container.
When you have ground the desired amount, set the switch back to "OFF".

Grinding coffee directly in the group handle

The CM 80 / CM 81 coffee grinder was built to fit our ES 80 and ES 90 filter bracket automatic machines.

Take hold of the group handle in the ES 80 or ES 90 automatic machine group handle.
Put the supplied hose over the coffee grinder outlet.
◆ Hold the group handle between the group handle bracket.

Line drawing of a hand using a coffee maker to handle a cup (no text or symbols)

NOTE

There are two different sizes of group handle brackets.
The small one is for the group handle in the ES 80 group handle automatic machine.
The large one is for the group handle in the ES 90 group handle automatic machine.

◆ Set the switch to "Auto"

Line drawing of a hand using a handheld device to interact with a surface (no text or symbols)

◆ Press the group handle onto the button between the group handle brackets.

Line drawing of a hand pouring liquid into a washing machine with a red arrow indicating flow direction (no text or symbols)

◆ The coffee flows into the group handle.
When the group handle is full, pull it back.
◆ The coffee stops flowing.
◆ Set the switch back to "Off"

NOTE

If the cutters block due to any possible stones or other foreign bodies do not use force. Switch the unit off, pull the power cord and clean the unit as described under "Cleaning and Care". You can now put the unit back into operation. If it nevertheless does not function, contact a specialist or GRAEF factory customer service.

Cleaning and Care

This chapter provides you with important information on cleaning and caring for the unit.

Safety instructions

CAUTION

Follow the safety instructions below before you start cleaning the unit:

▶ Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
▶ Let the unit cool off before cleaning.
▶ Do not use any aggressive or abrasive cleaning agents and do not use any solvents.
▶ Do not scratch off stubborn soiling with hard objects.
▶ Make sure that no liquid gets into the interior of the unit.
▶ Do not put the unit in the dishwasher and do not hold it under flowing water.

Cleaning

EN

Old coffee remains in the unit can lead to oxidation. That spoils the beverage; it can cause an unpleasant, rancid taste. The units should always be in optimum condition to be able to provide optimum espresso at any time.

Clean the unit at least 1 x week.

IMPORTANT!

▶ Ensure the unit is switched off and unplugged from the power outlet.

■ Clean the exterior of the unit with a soft, moist cloth. If heavily soiled, a mild detergent can be used.
■ Take off the coffee bean container. Press it down and turn counter clockwise

Hand pouring liquid into a jar with red arrows indicating motion (no text or symbols)

■ Take out the unused beans and put them in an airtight container so they stay fresh.
■ Clean the coffee bean container and the coffee container with

warm water and a little deter- gent.

■ After that, dry both receptacles well.

Cleaning the mill

IMPORTANT!

▶ Ensure the unit is switched off and unplugged from the power outlet.

■ Remove the coffee bean container as described in "Cleaning".
■ To remove the upper mill, turn the latching ring counter clockwise until it no longer turns.

Illustration of hands holding a cylindrical object with a red arrow indicating direction (no text or symbols)

■ Press and hold the "UNLOCK" button on the rear of the motor block.
■ With your other hand, turn the latching ring counter clockwise until the arrow on the latching ring matches the arrow on the motor block.

Line drawing of two hands holding a small cylindrical object (no text or symbols)

NOTE

The upper mill can only be removed if the arrow on the latching ring and the arrow on the motor block face each other.

■ Use the handle to remove the upper mill and clean it with the brush.

Line drawing of a hand pouring liquid into a bottle (no text or symbols)

■ When you have finished cleaning everything, put the latching ring back on the motor block. The arrows must once again point to each other. Replace the upper mill.

■ Turn the latching ring clockwise until you have reached the desired grind setting. (You can hear a latching sound).

■ Now take the latching ring off the motor block and clean it with the brush.

Line drawing of a hand holding a cylindrical device with a knob (no text or symbols)

■ Also clean the bottom of the mill with the small brush.

Line drawing of a cylindrical device with a central lid and handle (no text or symbols)

Disposal

EN

GRAEF CM 81 - Disposal - 1

At the end of its service life, this product must not be disposed through normal domestic waste; rather it must be disposed at a collection point for recycling electronic domestic refuse. The symbol on the product and in the operating instructions points this out. The materials can be recycled in accordance with their markings. By recycling, making use of the materials or other forms of recycling old units you are making an important contribution to protecting our environment. Please ask your municipal administration about the responsible disposal sites.

Warranty

2 year warranty

Starting with the date of purchase, we assume a 24 month manufacturer's warranty for defects that are attributable to manufacturing and material defects. Your legal warranty rights in accordance with § 439 ff. German Civil Code-E remain unaffected by this clause. Not included in the warranty are damages that have arisen due to improper handling and use as well as defects which have only a slight influence on the functioning or value of the unit. Furthermore, shipping damages, unless our responsibility, are excluded from warranty rights. Warranty claims are excluded for damages that arise due to repairs we or our representatives have not performed. In case of a justified complaint, we will repair or replace the defective product with a flawless product as we choose.

Préface

Chère cliente, cher client,

Simple line drawing of a curved mechanical part with a labeled number 8 (no text or symbols on the shape itself)

Simple line drawing of a tool or brush with a handle and spout (no text or symbols)

REMARQUE

Simple line drawing of a curved mechanical part with a labeled number 8 (no text or symbols on the shape itself)

Simple line drawing of a tool or plunger with a handle and lined tip (no text or symbols)

Datos técnicos

NOTA

NOTA

Simple line drawing of a curved mechanical part with a labeled number 8 (no text or symbols on the shape itself)

Simple line drawing of a tool or plunger with a handle and lined tip (no text or symbols)

Dati tecnici

NOTA

NOTA

Simple line drawing of a curved mechanical part with a labeled number 8 (no text or symbols on the part itself)

Simple line drawing of a tool or plunger with a handle and lined tip (no text or symbols)

Technische gegevens

◆ Stel de gewenste maalgraad in.

Illustration of a hand holding a cup with red arrows indicating motion or force direction (no text or symbols)

OPMERKING

OPMERKING

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : GRAEF

Model : CM 81

Category : Coffee grinder