K 2160 TST - Pressure washer KRANZLE - Free user manual and instructions

USER MANUAL K 2160 TST KRANZLE

High-pressure cleaners

K 2160 TS

K 2160 TS T

K 2195 TS

K 2195 TS T

K 2175 TS

K 2175 TS T

Blue Kranzle 2160 TST pressure water heater with attached hose and control panel (no visible text or symbols on body)

Read and conform safety instructions before use!

Keep instructions in a safe place for later use and pass them on to any future user.

2

Description

Kränzle 2160 TS, 2160 TST,

Kränzle 2195 TS, 2195 TST,

Kränzle 2175 TS, 2175 TST

Kranzle®

Ergonomically shaped handle

Cable reel with 5 m cable

Receptacle for gun with spray lance (during breaks)

Generously dimensioned hose drum with 15 m steel braided high-pressure hose

(only available for TST models)

Hand crank (only available for TST models)

Ergonomically shaped handle High-pressure gun

Large stainless steel manometer

Fully adjustable pressure control Detergent hose with filter

Interchangeable lance with Dirtkiller nozzle Interchangeable washing lance

On/Off switch with signal lamp and motor protection

Receptacle for high-pressure gun

Receptacle for Dirtkiller and lance

Generously dimensioned trolley suited for difficult terrain and stairs

Contents

Page

Description 2

Contents 3

Technical data 4

Overview "This is what you have purchased" 6

General rules 7

Safety precautions – accident prevention 8

Extremely important: Water connection – electrical connection 10

Kränzle-technology 12

Water and cleaning system 12

Lance and spray gun 12

Pressure control valve – safety valve 12

Motor protecting switch 13

High pressure hose and spray device 13

Total stop system 13

Putting into operation 14

Connection to water mains 14

Direct suction 17

When using detergents 18

To shut down the pump / frost protection 19

Small repairs – do it yourself! 20

Inspections – inspection reports 24

EG – Declaration of Conformity 26

Guarantee 27

Accessories for high-pressure cleaners 28

Spare parts list 30

Complete assembly 30

Valve housing 32

Unloader valve and pressure switch 34

Motor 36

Transmission 38

Hose drum 39

Gun with lance 40

Dirtkiller with lance 41

Wiring diagrams 43

4 Technical data

Line drawing of a Kränzle water heater with attached pump and wheels (no text or symbols)

Technical line drawing of a Kränze water heater with visible components and branding (no text or symbols beyond branding)

	Kränzle2160 TS	Kränzle2160 TS T	Kränzle2195 TS	Kränzle2195 TS T
Operating press. fully adjustable	30 - 140 bar	30 - 180 bar
Nozzle size 25042 25030
Permissible overpressure 160 bar	195 bar
Water output at	1,400 r.p.m. 11 l/min		at 1,400 r.p.m. 8 l/min
Water inlet temperature max.	60 °C	max. 60 °C
Suction height 2.5 m	2.5 m
Hose drum	no	yes	no	yes
Steel braided high-pressure hose	10 m	15 m	10 m	15 m
Detergent suction	yes		yes
Connected load 230 V~ 50 Hz,	14 A	230 V~ 50 Hz	14 A
Power input	P 1 - 3.2 kW		P 1 - 3.2 kW
Power output	P 2 - 2.4 kW		P 2 - 2.4 kW
Weight	37 kg	39,5 kg	37 kg	39.5 kg
Dim. incl. pulling handle in mm	900 x 375 x 360		900 x 375 x 360
Sound level acc. to DIN 45 635	78 dB (A)		81 dB (A)
Sound level with Dirtkiller	82 dB (A)		78 dB (A)
Acoustic power L_WA	89 dB (A)		91 dB (A)
Recoil at lance	approx. 25 N		approx. 25 N
Vibration at lance	2.0 m/s ^2		2.0 m/s ^2

Line drawing of a Kranze water heater with attached pump and wheels (no text or symbols)

Kränzle 2175 TS

Technical line drawing of a Kvarde air purifier with attached hoses and control panel (no text or symbols)

Kränzle 2175 TS T

Operating press. fully adjustable 30 - 160 bar 30 - 160 bar

Nozzle size 25042 25042

Permissible overpressure 175 bar 175 bar

Water output at 1,400 r.p.m. 12 l/min at 1.400 r.p.m. 12 l/min

Water inlet temperature max. 60 °C max. 60 °C

Suction height 2.5 m 2.5 m

Hose drum no yes

Steel braided high-pressure hose 10 m 15 m

Detergent suction yes yes

Connected load 400 V\~50 Hz, 6.7 A 400 V\~50 Hz, 6.7 A

Power input P 1 - 3.3 kW P 1 - 3.3 kW

Power output P 2 - 2.6 kW P 2 - 2.6 kW

Weight 37 kg 39,5 kg

Dim. incl. pulling handle in mm 900 x 375 x 360 900 x 375 x 360

Sound level acc. to DIN 45 635 78 dB (A) 78 dB (A)

Sound level with Dirtkiller 82 dB (A) 82 dB (A)

Acoustic power L_WA 91 dB (A) 91 dB (A)

Recoil at lance approx. 27 N approx. 27 N

Vibration at lance 2.1 m/s ^4 2.1 m/s ^2

6 This is what you have purchased

Line drawing of a mechanical vehicle with wheels and a wheel assembly (no text or symbols)

1. Kränzle high-pressure cleaners 2160 TST, 2195 TST, 2175 TST with 15 m steel braided high-pressure hose and hose drum NW 6

Line drawing of a portable water dispenser with coiled hoses (no text or symbols)

or

Kränzle high-pressure cleaners 2160 TS, 2195 TS, 2175 TS with 10 m steel braided high-pressure hose but without hose drum NW 6

Line drawing of a cleaning spray gun (no text or symbols)

1. Trigger gun with safety catch, insulated handle and screw connection

1. Dirtkiller lance with stainless steel pipe

1. Vario-Jet lance with stainless steel pipe

1. Handle with fixing screw for hose drum

Range of application

Use machines for cleaning tasks with high-pressure water jet and detergents or with high-pressure water jet without detergents only.

Inspections

The machine must be inspected according to the “Guidelines for Liquid Spray Devices” at least once every 12 months by a qualified person, to ensure that continued safe operation is guaranteed. The results of the inspection are to be recorded in writing. This may be done in any form. For inspection reports see pages 22 - 25.

High-pressure cleaners used for commercial purposes have to be checked by a qualified person at least every 12 months!

■Accident prevention

The machine is designed for accidents to be impossible if used correctly. The operator is to be notified of the risk of injury from hot machine parts and the high pressure water jet. The “Guidelines for Liquid Spray Devices” must be complied with. (see pages 8 and 9).

Dil change:

The first oil change should be carried out after approximately 50 operating hours, then every year or after 1000 operating hours. If the oil turns grey or white, you must change the oil of your high pressure pump in any case.

Put the machine into a horizontal position, then open the oil discharge screw at the bottom of the device over a collection reservoir. The oil is to be caught in the reservoir and disposed of in an approved manner.

New oil: 0,35 l - Motor oil W 15/40.

Oil leakage: If oil leaks contact your nearest after-sales service (dealer) at once. (Ecological damage, damage to the transmission)

In case of increased humidity or fluctuations in temperature development of condensed water is possible; if the oil turns grey, you must change it.

8 Safety precautions

Illustration of a person using a power tool to clean or spray a machine (no text or symbols present)

Bear in mind that during cleaning tasks with a high-pressure water jet a significant recoil at the lance arises (see technical data on page 4).

Technical line drawing of a fuel pump tool with no visible text or symbols

Apply the safety catch on the trigger gun after each use, in order to prevent unintentional spraying!

Diagram of a vehicle's wheel assembly with water spray and tool, showing mechanical components and motion arrows (no text or symbols)

Always aim the underbody lance! Bear in mind when using a curved or angled spraying lance that there is a significant amount of torque in the recoil!

Safety precautions - That's forbidden!

Illustration of a dog and two adults walking with a dog pulling a dog via a streetlamp, no text or symbols present

Never direct the water jet at people or animals!

Pure electrical circuit lines without any symbols

Only use power cables which are in perfect working order! Do not damage the power cable or repair it incorrectly!

Illustration of a person cleaning a large machine with a crossed-out X symbol (no text or symbols present)

Never pull the high pressure hose if it has formed kinks or "nooses"! Never pull the hose over sharp edges!

Illustration of a child spraying water with a X symbol (no text or labels)

Never allow children to use the high pressure cleaner!

Illustration of a person cleaning a lawn with a mobile phone and a cross symbol (no text or symbols present)

Never direct the water jet at the machine itself!

Diagram showing a tool emitting particles from a droplet onto a surface, with no text or symbols present.

Never direct the water jet at a power socket!

10 Please note - important!

Lack of water

Illustration of a hand interacting with a fingerprint inside a bucket, no text or symbols present

Lack of water occurs more often than you probably believe. The more powerful a high-cleaner is the greater is the danger that a lack of water occurs. If there is only an insufficient amount of water available, cavitation arises inside the pump, which is normally noticed too late or even not at all.

The pump will be destroyed!

Please check the available quantity of water by filling a bucket with litre scale for one minute.

The following minimum quantity of water is necessary for a safe and problem-free operation of the high-pressure cleaner:

If the metered quantity of water is too small, you have to use a different water connection, guaranteeing the necessary output.

Lack of water leads to an accelerated wear of the joints (no guarantee).

■Connection to water supply

Please pay attention to the regulations of your waterworks company! In accordance with DIN EN 61770, the machine may not be directly connected to the public drinking water supply lines. A brief connection however is permissible according to DVGW (German Association for Gas and Water Affairs) if a tube ventilator with check valve (Kränzle Order-No. 41.016 4) is built into the water supply. Also indirect connection to the public drinking water supply lines is permissible by way of free emission in accordance with EN 61 770; e.g. by using a reservoir with a float valve.

Direct connection to a non-drinking water supply line is permissible.

■ Insufficient quantity of electricity

226

If there are too many collectors in your proximity connected to the network at the same time, the available voltage and the current intensity may decline.

Consequently the motor of the high-pressure cleaner does not start or even blows.

The power supply may also be insufficient if the power cable is too long or too thin. If extension cables are too long, this may lead to a voltage drop causing malfunctions or start-up difficulties.

Connected load:

Kränzle 2160 TS / TS T: 230 V \~, 50 Hz

Kränzle 2195 TS / TS T: 230 V \~, 50 Hz

Kränzle 2175 TS / TS T: 400 V, 50 Hz (phase-sequence not significant)

Check the line fusing and have the voltage and the available current intensity checked by an expert in case of uncertainty.

Electrical connection

The machine is supplied with an electrical power cable with plug. The mains plug must be fitted to a standard grounded socket with a 30mA residual current operated device. The socket must be protected with a 16A delay action fuse on the mains side. When using an extension cable, this must have an earthed lead which is properly connected to the socket. The conductors in the extension cable must have a minimum cross section of 1.5 mm^2 . Plug connections must be of a spray-proof design, and may not be located on a wet floor. With extension cables of more than 10 m the minimum cross section must be 2.5 mm! When using a cable drum, always keep the cable wound as far as possible.

12 Kränzle technology

Water and Cleaning System

Water can be connected at mains pressure to the high pressure pump or it can be sucked directly from a storage tank. The water is then forced under pressure by the high pressure pump to the lance. The high pressure jet is formed by the nozzle at the end of the lance.

Environmental, refuse disposal and water protection regulations must be observed!

■Lance with trigger gun

The machine can only be operated when the safety trigger is squeezed. When the lever is squeezed, the spray gun opens. The liquid is then pumped to the nozzle. The spray pressure increases and quickly reaches the selected operating pressure. When the trigger is released, the trigger gun closes and any further spraying of liquid from the lance is stopped. The pressure gauge must show 0 bar.

The increase in pressure when the trigger gun is closed causes the pressure control valve-safety valve to open. The motor is switched off by the pressure switch. When the trigger gun is opened, the pressure control valve - safety valve closes, the motor is started and the pump resumes pressure spraying from the lance with the selected operating pressure.

The trigger gun is a safety device. Repairs should only be performed by qualified persons. Should replacement parts be required, use only components authorized by the manufacturer.

■Pressure control valve - safety valve

The pressure control valve - safety valve protects the machine from a build up of excess pressure, and is designed not to permit an excess pressure to be selected for operation. The limit nut on the handle is sealed with a spray coating. The operating pressure and spray rate can be steplessly adjusted by turning the handle.

Replacements, repairs, new adjustments and sealing should only be performed by qualified persons.

Motor protection switch

The motor is protected from overload by a motor protection switch, which cuts out the motor in the event of overload. However should the switch trip frequently, the cause of the malfunction should be located and rectified (see page 11).

Replacements and inspection work should only be performed by qualified persons when the machine is disconnected from the power supply, i.e. with plug pulled out from the electrical socket.

■High pressure hose and spray device

The high pressure hose and spraying device supplied with the machine are made of high grade material, they are also optimised for the machine and marked as required by the appropriate regulations.

If replacement parts are required, only such parts that are authorised by the manufacturer and which bear the markings required by the appropriate regulations may be used. The high pressure hose and spray device must be connected in a pressure-tight manner. The high pressure hose may not be driven over, pulled excessively, or twisted. The hose may under no circumstances be pulled over sharp edges, since otherwise the guarantee is automatically void.

■ Total stop system

The new Kränzle K2160 / K2195 / K2175 are equipped with an electrical Start/Stop control. Having connected the high-pressure cleaner to the water supply and having connected the HP hose, switch the machine “on” using the On/Off switch. A red light in the switch flashes.

The motor is started by opening the gun. The motor is switched off after the gun has been closed. The high-pressure cleaner works in stand-by until the On/Off switch is switched to "Off". The red light in the switch goes out.

Having switched off the machine shortly press the trigger to release the pressure to be able to unfasten the HP hose.

14 Putting into operation

Line drawing of a person in protective suit pushing a lawn mower next to a portable cleaning vehicle (no text or symbols)

1. Move high-pressure cleaner to the job site.

The Kränzle 2160 / 2195 / 2175 are movable machines with sturdy trolleys ideally suited for difficult terrain and stairs.

Never pull the machine if the water supply hose is still connected!

Setting up – Location

Neither set up or operate the machine in rooms where there is a risk of fire or explosion nor put it into puddles. Do not use the machine under water.

Mechanical assembly diagram showing a hand using a tool to adjust a component with arrows indicating motion (no text or symbols present)

1. Check water inlet filter for cleanliness prior to putting the machine into operation!

Manually unscrew hose attachment. Take out the serial water inlet filter using needle nose pliers and clean if filter is soiled.

Technical line drawing of a vehicle engine compartment with valve and pressure gauge (no text or symbols)

1. Each time check oil level at the oil dipstick prior to putting the HP cleaner into operation. (Take care that cleaner is in horizontal position!)

The oil level must show between the two markings.

Mechanical assembly diagram showing a wheel and lever mechanism with no visible text or symbols

1. Put up machine. Release fixing screw from hexagonal base of hose drum, put tiltable handle onto the hexagonal base and fix with screw.

Diagram showing two-step tool manipulation: one with a tool inserted into a connector, the other with a curved tool and arrow indicating rotation (no text or symbols)

1. Push on lance or Dirtkiller lance to gun.
2. Screw together lance and gun.

Two-step diagram showing a spray gun being inserted into a hose, with no text or symbols present.

1. Push on HP hose to gun.
2. Screw together HP hose and gun.

Technical diagram of a car engine showing internal components and motion arrows (no text or labels)

1. Put HP cleaner into horizontal position. These machines must be operated in horizontal position! Unwind HP hose from hose drum without kinks and nooses.

Technical diagram of a vehicle's engine compartment showing hoses and wiring (no text or labels)

1. Connect water hose to water tank. The cleaner may be connected to water mains with cold or 60°C warm water. Alternatively water can be sucked in from a container (see page 17).

■ Be careful when using hot water!

When running your high pressure cleaner with hot water of 60^ C raised temperatures occur. Do not touch the metal parts of the cleaner without safety gloves!

16

Putting into operation

Illustration of a power plug connected to a wall socket (no text or symbols)

1. Connect to circuit. Kränzle 2160 TS / TS T: 230 Volt, 50 Hz. Kränzle 2195 TS / TS T: 230 Volt, 50 Hz. Kränzle 2175 TS / TS T: 400 Volt, 50 Hz. The socket must be protected with a 16A delay action fuse on the mains side.

Line drawing of a car engine bay with a valve and pressure gauge (no text or symbols)

1. Steplessly adjust operating pressure with handwheel. The maximum pressure is adjusted ex work.

Line drawing of a person in protective suit using a lawn mower to clean or spray equipment (no text or symbols)

1. Ventilation of the machine: Pull and release the trigger several times. Switch on high-pressure cleaner with opened spray gun. Start cleaning task.

Direct suction

Due the suction capacity of its pump (up to 2.5 m suction height, max. hose length 3 m) this high-pressure cleaner can suck in water for cleaning purposes from separate containers or ponds.

Prior to starting the first suction the pump resp. the suction hose has to be filled with water!

Technical diagram of a vehicle engine component with hoses and valve (no text or labels)

1. Mount suction hose with suction filter (Kränzle accessories No. 15.038 3). When using other hoses the inner cross section of the hose must be at least 3/4" = 16 mm.

2. Fill suction hose with water.

Diagram of a mechanical or fluidic device with a coiled pipe and a container, no text or symbols present

1. Put filled suction hose into the container and start the cleaning job.

Technical line drawing of a roof structure with ladder, curved railings, and cable (no text or symbols)

Use clean water only! Never suck in water containing chlorine.

Note

Depending on the water quality it may occur after a prolonged standstill that the valves get sticky. Consequently the machine cannot properly suck in water from a container.

In this case connect a hose with pressurized water to the pump inlet. Having started the machine the pressurized water opens the valves and the machine resumes sucking in water from the container. Now you can carry on with your cleaning task as usual.

18

Suction of detergents

■with detergent supply:

For the Kränzle 2160 TS / TS T, 2195 TS / TS T and 2175 TS / TS T a built-in injector provides the facility to suck in detergents.

By pushing the Vario-Jet nozzle to the front the machine is adjusted to low pressure and a vaccum is build up in the injector. Thus the detergent can be sucked in via the connected suction hose with filter.

Technical line drawing of a mechanical assembly with hoses and components (no text or symbols)

1. Place chemicals filter into container with cleansing agent.

Diagram of a hairdryer with an arrow indicating direction (no text or symbols)

1. To reach the low pressure push Vario nozzle to the front so that the injector can suck in the cleansing agent.

Diagram showing a droplet being sprayed into a pipe with an arrow indicating direction (no text or symbols)

1. The chemicals supply is automatically stopped when closing the Vario nozzle by pushing it backwards.

Let cleansing agent take effect and then spray off with a high-pressure jet.

The pH value neutral 7-9 is prescribed for the detergents. Only use detergents suitable for high-pressure cleaners. Observe specifications of detergent manufacturer! e.g.: protective equipment, rules for waste water treatment etc.

Never suck in liquids containing solvents like varnish solvents, petrol, oil or similar liquid! Observe specifications of detergent manufacturers! Seals inside the appliance are no resistant against solvents! The spray mist of solvents is highly inflammable, explosive and poisonous.

To shut down the pump

1. Switch off the machine
2. Cut off the water supply
3. Open the spray gun briefly until the pressure is released
4. Apply the safety catch on the spray gun
5. Remove the water hose and spray gun
6. Drain the pump: switch on the motor for approx. 20 seconds
7. Pull the plug from the socket
8. Clean HP hose and wind up
9. Clean power cable and wind up
10. Clean water filter
11. Winter: store the pump in rooms above 0^ C

■ Store in a place-saving manner

Line drawing of a cleaning machine with broom and bicycle nearby (no text or symbols)

Due to their compact and space saving design these Kränzle-2000 cleaners can be stored practically anywhere.

20 Small repairs - do it yourself!

■o water from the nozzle but the gauge shows full pressure:

Most likely the nozzle is blocked.

100 2000 150 200 1000 50 3000 250

The pressure gauge shows full pressure, but from the nozzle comes only little water or no water at all.

(Inside the pressure gauge is no water but a filling with glycol to damp the vibration of the pointer.)

Switch off the cleaner. Pull plug from the socket. Operate gun seveal times to decrease the pressure.

First unscrew gun and lance, then rinse hose from any residues.

Line drawing of a magnifying glass inspecting internal components (no text or symbols)

Check water inlet filter for soiling.

If the problem still exists, take wire (paper clip) and push through nozzle opening.

If this procedure is not successful, the nozzle has to be dismantled and cleaned or even replaced, if necessary.

CAUTION! Pull plug from socket prior to starting any repair work!

■ Pressure gauge shows little pressure, the water from the nozzle comes in squirts: Most likely the valves are soiled or sticky.

100 2000 150 200 1000 50 3000 0 250

The pressure gauge shows little pressure despite fully turned up pressure regulation. The water from the lance comes in squirts. The HP hose vibrates.

(Inside the pressure gauge is no water but a filling with glycol to damp the vibration of the pointer.)

Mechanical assembly diagram showing a lever mechanism with no visible text or symbols

Unscrew all 6 valves, one after the other (hexagonal brass screws, 3 in a row, vertically and horizontally)

Mechanical assembly diagram showing a tool inserted into a component with no visible text or symbols

Take out valve body (with green or red plastic coating) and O-ring by means of needle nose pliers. Check O-ring for damage. In case of a damage the O-ring has to be replaced.

Illustration of a hand holding a small electronic component with an arrow indicating direction (no text or symbols present)

Take a wire (paper clip) and clean valves under running water. Also clean valve seat inside the pump.

Do not forget the O-ring during reassembly!

22 Small repairs - do it yourself!

■The pressure gauge shows full pressure although the gun has been closed. The pressure switch valve switches constantly.

100 2000 150 200 1000 50 3000 0 250

Line drawing of a spray gun with water droplets spraying from its tip (no text or symbols)

Diagram of a cable connector with internal components and directional arrows indicating movement (no text or symbols)

Possible cause no.1: Leakage

Having closed th gun, the HP cleaner must shut down and the pressure gauge must show „0“ bar.

If the pressure gauge still shows full pressure and the motor constantly switches on and off, the possible reason for this can be a leakage of the pump, the HP hose or the lance.

Proceeding:

Check the connections from the HP cleaner to the the HP hose, from the hose to the gun and also the connection between lance and gun for tightness.

Switch off the cleaner. Shortly pull the trigger of the gun to decrease the pressure.

Unscrew HP hose, gun and lance and check the O-rings.

If the O-rings are damaged they have to be replaced.

Caution! In case of a leakage there is no guarantee for possible consequential damages.

The pressure gauge shows full pressure although the gun has been closed. The pressure switch valve switches constantly.

Possible cause no. 2: The return body is soiled or the sealing ring on the return body is defective.

Mechanical assembly diagram showing a wrench inserted into a housing with bolted components (no text or labels)

Unscrew pump outlet.

Technical line drawing of a mechanical assembly with no visible text or symbols

Take out check ball and check for soiling or damage of ball or stainless steel seat inside the pump housing.

Diagram showing a hexagonal bolt with two arrows indicating direction and a separate spring component, labeled with the number 0.

Replace non-return valve if necessary.

Caution ! There is no guarantee if the pump is damaged by defective O-rings due to air induction or lack of water (cavitation).

24 Inspection report for HP cleaners

HP cleaners for industrial use have to be checked by an expert every 12 months! Inspection report on annually carried out Labour Safety Inspection (UVV) according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for the completion of the retest and must be kept carefully!) Kränzle test seals: Order no. UVV200106

Owner: Type:

Address: Serial no.:

Rep. order no.:

Scope of inspection o.k. yes no repaired

Type plate (on hand)
Operating manual (on hand)
Protective covering, -device
Pressure line (tightness)
Pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
HP-hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding of operating pr.
Power cable (damage)
Protective conductor (connected)
On / Off switch
Used chemicals
Allowed chemicals

Inspection data	determined value	set value
High-prsure nozzle
Operating pressure......bar
Switch off pressure......bar
Conductor reist. not exceeded / value
Insulation
Leakage current
Gun locked

Inspection result (tick)

The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment, the defects found have been rectified so that the Labour Safety can be confirmed.
The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment. The Labour Safety cannot be confirmed unless the defects found are rectified by repair or replacement of the faulty parts

The next retest according to the Guidelines for Liquid Spray Equipment has to be carried out by: Month ____ Year ____

Place, date Signature

Inspection report for HP cleaners

HP cleaners for industrial use have to be checked by an expert every 12 months!

Inspection report on annually carried out Labour Safety Inspection (UVV) according to

the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for

the completion of the retest and must be kept carefully!) Kränzle test seals: Order no. UVV200106

Owner:

Type:

Address:

Serial no.:

Rep. order no.:

Scope of inspection
o.k. yes no repaired

Type plate (on hand)
Operating manual (on hand)
Protective covering, -device
Pressure line (tightness)
Pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
HP-hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding of operating pr.
Power cable (damage)
Protective conductor (connected)
On / Off switch
Used chemicals
Allowed chemicals

Inspection data
determined value set value

High-prsure nozzle
Operating pressure......bar
Switch off pressure......bar
Conductor reist. not exceeded / value
Insulation
Leakage current
Gun locked

Inspection result (tick)

The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment, the defects found have been rectified so that the Labour Safety can be confirmed.
The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment. The Labour Safety cannot be confirmed unless the defects found are rectified by repair or replacement of the faulty parts

The next retest according to the Guidelines for Liquid Spray Equipment has to be carried out by: Month ____ Year ____

Place, date ____ Signature ____

26

EC declaration of conformity

Hereby we declare that:

technical specifications available from:

comply with the following guidelines and their amendments for high-pressure cleaners:

machinery directive 2006/42/EEC,

EMC-directive 2004/108 EEC,

noise directive 2005/88/EC, Art. 13,

HP water spraying machines

annex 3, part B, chapter 27

Sound level measured:

Sound level guaranteed:

Applied conformity evaluation procedures

annex V, noise directive 2005/88/EC

Applied specifications and standards:

EN 60 335-2-79 :2004

EN 55 014-1 :2006

EN 61 000-3-2 :2006

EN 61 000-3-3 :2008

I. Kränzle GmbH

Elpke 97 D - 33605 Bielefeld

The guarantee is only valid for material and manufacturing errors.

Wearing does not fall within this guarantee.

The instructions in our operating manual must be complied with..

The operating instructions form part of the guarantee. The Guarantee is void if other parts are used than genuine Kränzle accessory parts or genuine Kränzle spare parts.

For high-pressure cleaners sold to the user the guarantee period is 24 month.

For high-pressure cleaners sold for industrial use the guarantee period is 12 month.

In the case of a guarantee please contact your dealer or authorized seller delivering accessories and your purchase receipt. You can fin them in the internet under

www.kraenzle.com.

The guarantee is also void if the machine is used with exceeding the temperature and speed limits, a voltage below the required rating, with less than the required amount of water or with dirty water.

Pressure gauge, nozzle, valves, sleeves, high pressure hose and spray equipment are wear parts and are not covered by the warranty.

28

Versatile due to Kränzle accessories

Line drawing of a cleaning brush with a handle and bristles (no text or symbols)

Rotating washing brush with 400 mm extension, Order no. 41 050 1

Line drawing of a worker using a cleaning tool to clean or wash material (no text or symbols)

Line drawing of a mechanical tool or pipe fitting with a curved end and flange (no text or symbols)

Underbody lance with 800 mm extension, Order no. 41 075

Technical line drawing of a vehicle's wheel assembly with hoses and spray nozzle (no text or symbols)

Diagram of a coiled hose with two connectors (no text or symbols)

Pipe cleaning hose with nozzle,

10 m - Order no. 41 058 1

20 m - Order no. 41 058 2

25 m - Order no. 41 058 3

30 m - Order no. 41 058 4

Illustration of a person using a hose to clean or install equipment under a solar panel array (no text or symbols)

Line drawing of a medical or laboratory instrument with a long rod and flanged tip (no text or symbols)

Sludge sucker, stainless steel,

Order no. 41 801

Sludge sucker with 3 m suction hose,

Order no. 41 104

Line drawing of a person using a hose to clean water from a pipe in a field (no text or symbols)

Technical line drawing of a cleaning or cleaning tool with a handle and circular base (no text or symbols)

Floor cleaner round cleaner UFO

Order no. 41.850

Line drawing of a person in protective suit using a cleaning tool (no text or symbols)

Line drawing of a coiled hose with a handle and bulb (no text or symbols)

Sand blasting set compl. up to 12 l/min, 150 bar

Order no. 41 068 1

Sand blasting set compl. up to bis 19 l/min, 250

bar Order no. 41 068

Diagram of a spray gun spraying water onto a pipe, with no visible text or symbols

30

Spare parts list

Kränzle 2160 / 2195 / 2175

Exploded view diagram of a car's internal components with numbered parts and labeled parts

Complete assembly
No Description Qty. Ord.-No

Exploded view diagram of a mechanical assembly with numbered parts for identification

Valve housing 18mm

No Description Qty. Ord.-No

Exploded view diagram of a mechanical assembly with numbered parts for identification

Valve housing 15mm

No Description Qty. Ord.-No

No Description Qty. Ord.-No

Unloader valve and pressure switch

No Description Qty. Ord.-No

Exploded view diagram of an electric motor assembly with numbered components and exploded views

Motor

No Description Qty. Ord.-No

Exploded view diagram of an electric motor assembly with numbered parts for identification

No Description Qty. Ord.-No

Exploded view diagram of an electric motor assembly with numbered parts for identification

No Description Qty. Ord.-No

Technical diagram of a bicycle steering wheel assembly with numbered components for identification

Hose drum

No Description Qty. Ord.-No

Exploded view diagram of a spray gun assembly with numbered parts for identification

No Description Qty. Ord.-No

Dirtkiller with lance

Exploded view diagram of a mechanical device with numbered parts for identification

No Description
Qty. Ord.-No

Reprint only allowed with the authorisation of Kränzle.

As date of 26.01.2013

Made
in
Germany