HR-S7955MS - VCR JVC - Free user manual and instructions

Product type	S-VHS/VHS VCR
Brand	JVC
Model	HR-S7955MS
Dimensions (W x H x D)	400 x 94 x 270 mm
Weight	3.4 kg
Power supply	220-240 V~, 50/60 Hz
Power consumption (operation)	20 W
Power consumption (standby)	3.3 W
Supported video formats	S-VHS, VHS (PAL/SECAM)
Recording speeds	SP, LP, EP
Timer programming capacity	8 programs over 1 year
SHOWVIEW system	Integrated
Connections	2 SCART (AV1 input/output, AV2 input/decoder), RCA audio/video inputs/outputs, S-Video, antenna
Special features	Insert editing, audio dubbing, S-VHS ET, T-V LINK, satellite controller
Safety	Anti-accidental erasure protection, automatic stop in pause, image stabilizer
Maintenance	Use JVC ECL-3 cleaning cassette for video heads
Operating temperature	5°C to 40°C
Supplied accessories	RF cable, SCART cable, remote control, batteries
Repairability	Spare parts available from JVC after-sales service

Frequently Asked Questions - HR-S7955MS JVC

How to set the clock automatically?

On first start-up, the VCR performs automatic setting via the PDC signal. If this fails, you can set the clock manually in the menu Initial Settings > Time Setting, using the +/− keys to enter the date and time.

How to use the ShowView system to program a recording?

Press PROG, enter the ShowView number using the numeric keys, then press OK. Check the channel and adjust the recording speed (SP/LP/EP) if necessary. Press OK again to confirm, then press ⏺ to activate timer mode.

What to do if the picture is blurry or noisy?

First check that the video heads are clean: use a JVC ECL-3 cleaning cassette. If the problem persists, try adjusting the tracking manually by pressing TRACKING +/− during playback. Also make sure the SCART cable is properly connected.

How to connect the VCR to the TV?

Connect the antenna cable to the ANTENNA INPUT of the VCR, then connect the ANTENNA OUTPUT to the TV using the supplied RF cable. Also connect the SCART cable between AV1 (L-1) of the VCR and the SCART socket of the TV.

How to record a program without the ShowView code?

Use the express program recording: press PROG then START+/−. Enter the start time, end time, date and channel using the appropriate keys. Adjust the speed and press OK. Finally, activate timer mode with ⏺.

How to perform insert editing?

Insert the source cassette and the target cassette. In stop mode, press INSERT to activate insert mode. Select the start point on the target tape, then press PLAY to start editing. The video/audio signals from the source are inserted.

What to do if timer recording does not work?

Check that the clock is correctly set and that timer mode is activated (⏺ indicator lit). Make sure a cassette with intact safety tab is loaded. If the problem persists, erase existing programs and reprogram.

How to clean the video heads?

Use a JVC ECL-3 dry cleaning cassette. Insert it like a normal cassette and let it play for 10 to 15 seconds. Do not reuse the cleaning cassette too often to avoid head wear.

How to play a cassette recorded on another VCR?

Insert the cassette into the VCR. If the picture is unstable, press TRACKING +/− to adjust tracking. If the tape was recorded in LP/EP mode, the VCR adapts automatically. For S-VHS tapes, make sure S-VHS mode is activated.

What is the memory backup duration?

The memory retains settings (clock, programs) for approximately 10 minutes in case of power failure. Beyond that, the clock and programming must be reset.

USER MANUAL HR-S7955MS JVC

QUESTIONS AND ANSWERS 71

LIST OF TERMS 72

3 Start playback.

1 Start playback.

4 Start the camcorder.

Manual alignment. 23

AUTO STOP 59

List of TV stations and identification 65

M

: Helical scanning DA4 (Double Azimuth)