UTX-3117FS-S6A2N - Computers Advantech - Free user manual and instructions

USER MANUAL UTX-3117FS-S6A2N Advantech

Illustration of four electronic circuit boards with grid patterns, no text or symbols present

UTX-3117

Copyright

The documentation and the software included with this product are copyrighted 2018 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.

Acknowledgements

Intel® and Pentium® are trademarks of Intel Corporation.

Microsoft® Windows® and MS-DOS® are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.

Because of Advantech's high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandise authorization) number from your dealer. This allows us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

Part No. Edition 1

Printed in Taiwan March 2018

Declaration of Conformity

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning! Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to operate the equipment.

Caution! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Technical Support and Assistance

1. Visit the Advantech website at http://support.advantech.com where you can find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call:

– Product name and serial number
– Description of your peripheral attachments
- Description of your software (operating system, version, application software, etc.)
- A complete description of the problem
- The exact wording of any error messages

Warning! 1. Input voltage rated 12\~24 VDC, 3 \~ 5 A (DC Mode).

1. Packing: please carry the unit with both hands, handle with care.
2. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator.

Safety Instructions

1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's manual.
e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

1. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

2. If your computer is losing dramatic time or the BIOS configuration reset to default, the battery has no power.

Caution!

1. Do not replace power adaptor yourself. Please contact a qualified technician or your retail.

1. The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard used batteries according to the manufacturer's instructions.

2. CLASSIFICATION:

- Supply by Class I adapter - No applied part - Continuous Operation - Not AP or APG category

1. Follow the national requirement to dispose unit.

2. Maintenance: to properly maintain and clean the surfaces, use only the approved products or clean with a dry cloth.

3. Contact information: No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan 114, R.O.C TEL: [phone]

Industry Canada Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

French User Manual Statements for RSS Warnings

FCC/Industry Canada Two-Part Statement:

English Version

This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Version française

European Union Declaration of Conformity Statement

We, Advantech, declare under our sole responsibility that the product, model, is in conformity with all applicable essential requirements Necessary for CE marking, following the provisions of the European Council Directives 2004/108/EC (EMC Directive), 2006/95/EC (Low Voltage Directive), 1999/5/EC (Radio and Telecommunications Terminal Equipment Directive) and 2011/65/EU (ROHS Directive).

The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC, 2006/95/EC, 1999/5/EC and 2011/65/EU.

This symbol on the product indicates compliance with Directive 2002/96/EC (WEEE). Do not dispose of product in unsorted municiiple waste.

Please recycle this product in a responsible manner. Refer to local environmental regulations for proper recycling; do not dispose of product in unsorted municipal waste.

Packing List

Before installation, please ensure the following items have been shipped:

1 x UTX-3117 unit
1 x DC 12 V 36W power adaptor
1 x China RoHS
1 x Warranty card
1 x Chinese user manual

Ordering Information

P/N	CPU	SSD	Memory	WiFi	3G/LTE	Other RF	Antenna	OS
UTX-3117FS-S6A1N	PENTIUM N4200, 4C 2M 1.1GHz	32GB	4GB X 1	NA	NA	NA	4	NA
UTX-3117FS-S6A2N	CELERON N3350 2C 2M 1.1GHz	32GB	4GB X 1	NA	NA	NA	4	NA
UTX-3117FS-S6A2E	Atom X5-E3940 4C 2M 1.6GHz	32GB	4GB X 1	NA	NA	NA	4	NA
UTX-3117FSW-S6A1N	PENTIUM N4200, 4C 2M 1.1GHz	32GB	4GB X 1	NA	NA	NA	4	WIN 10
UTX-3117FSP-S6A2N	CELERON N3350 2C 2M 1.1GHz	32GB	4GB X 1	NA	NA	NA	4	Pulsar 8
UTX-3117C-S6A2N	CELERON N3350 2C 2M 1.1GHz	NA	NA	NA	NA	NA	NA	NA
UTX-3117C-S6A2E	Atom X5-E3940 4C 2M 1.6GHz	NA	NA	NA	NA	NA	NA	NA
UTX-3117C-S6A1N	PENTIUM N4200, 4C 2M 1.1GHz	NA	NA	NA	NA	NA	NA	NA
UTX-3117SA4-S6A1N	PENTIUM N4200, 4C 2M 1.1GHz	NA	4GB X 1	NA	NA	NA	4	NA
UTX-3117SA4-S6A2N	CELERON N3350 2C 2M 1.1GHz	NA	4GB X 1	NA	NA	NA	4	NA
UTX-3117SA4-S6A2E	Atom X5-E3940 4C 2M 1.6GHz	NA	4GB X 1	NA	NA	NA	4	NA

Compatibility List

Power Cord

Part Number Description
1700001524	Power Cable 3-pin 180cm, USA type(For power adapter 1757004096-01)
170203183C	Power Cable 3-pin 180cm, Europe type(For power adapter 1757004096-01)
170203180A	Power Cable 3-pin 180cm, UK type(For power adapter 1757004096-01)
1700008921	Power Cable 3-pin 183cm, PSE Mark type(For power adapter 1757004096-01)

Optional Items

Part Number	Description
1750008401-01	Antenna SMA(F)/MHF 12cm IP65 A9703219 for 3G/LTE
1750008402-01	Antenna R/P SMA(M) to MHF 14cm IP65 A97 for WSN
1750008403-01	NGFF R/P SMA (M) to MHF 12cm IP65 A9703
1750008424-01	LTE Antenna Dipole L=148.5mm 4dBi A9703 for LTE
1750008671-01	Dipole Ant.SMA/M-R 2.4/5G 2.5/4dBi BLK for WiFi
AIMB-0BRK-VM05E	UTX-3117 VESA Mount bracket kit
AIMB-0BRK-WM03E	UTX-3117 Wallmount bracket kit
AIMB-0BRK-DR05E	UTX-3117 DIN rail bracket kit

Contents

Chapter 1 Introduction......1

1.1 Overview....2
1.2 System Configuration....3
1.3 General Specifications....4

1.3.1 Standard PC Functions....4
1.3.2 Power Environmental....4

1.4 Mechanical Specifications....4

1.4.1 Mechanical Specifications (Terminal)....4
1.5 Environmental Specifications....5

Chapter 2 Jumper and Connector List ....7

2.1 Connectors & Jumpers....8

Figure 2.1 Top View....8
Figure 2.2 Bottom View ......9
Table 2.1: RS485/RS422selection pin header (J485/422)......10
Table 2.2: AT/ATX Mode Selection (PSON1)....10

2.2 Connectors....10

2.2.1 CPU-System on chip(SOC1) 10
2.2.2 BIOS Flash(SPI1) 11
2.2.3 DDR3L SO-DIMM Socket (DIMMA1)....11
2.2.4 DC input Connector(DCIN1)....11
2.2.5 MINIPCIE Connector (MINI-PCIE1)....12
2.2.6 SIM Card Socket (SIM1)....13
2.2.7 Low Pin Count Header (LPC1) 13
2.2.8 MINIPCIE and mSATA Connector (MINI-PCIE2) 14
2.2.9 SPI Programming Pin Header (SPI_CN1)....15
2.2.10 COM Port (COM1)....16
2.2.11 General Purpose I/O Pin Header (GPIO1)....16
2.2.12 HD Analog Audio Interface (AUDIO1)....17
2.2.13 COM Port (COM2)....17
2.2.14 Next Generation Form Factor (M.2_1)....18
2.2.15 SATA Signal Connector (SATA1)....19
2.2.16 USB 3.0 Connector(USB1)....19
2.2.17 USB 3.0 Connector(USB2)....19
2.2.18 SATA Power Connector (SATA_PWR1)....20
2.2.19 RJ45 Connector(LAN1)....20
2.2.20 RJ45 Connector(LAN1)....20
2.2.21 High Definition Multimedia Interface(HDMI1)....21
2.2.22 DisplayPort (DP1)....21
2.2.23 DDR3L SO-DIMM Socket (DIMMB1)....22
2.2.24 SATA LED(D10)....22
2.2.25 Power Button(PWRBTN1) 22

Chapter 3 Peripheral Installation ......23

3.1 HDD Installation....24
3.2 Mini PCIe Module Installation....26

Chapter 4 BIOS Setup 29

4.1 Introduction 30
4.2 Entering Setup 31

4.2.1 Main Menu.... 31
4.2.2 Advanced BIOS Features.... 32
4.2.3 Chipset.... 5 2
4.2.4 Security Boot 59
4.2.5 Boot 61
4.2.6 Save & Exit.... 62

Chapter 1

Introduction

This Chapter briefly introduces the UTX-3117 product.

1.1 Overview

The Advantech UTX-3117 system is fanless & extended=temp embedded box. The solution uses the latest Intel® Atom® E3900, Celeron® N3350, and Pentium® N4200 series processor technology to provide a real-time IoT computing, power-efficient, plug & play gateway which is ideal for smart city street lighting, smart metering, smart parking, smart agriculture, HVAC, healthcare, industrial automation and more. UTX-3117 is compatible with Microsoft Windows 10 IoT Enterprise, Yocto Linux, and Wind River Pulsar OS. Furthermore, UTX-3117 has Advantech intelligent software WISE-PaaS integrated and is certificated with AWS Greengrass IoT solution to offer a total solution for bridging connectivity from edge sensors to the cloud.

Benefits:

Ultra Thin ITX embedded system with CE/FCC certification
■ Fanless, wide-temperature operation with high performance and flexibility
■ Design in 3 extension slot for RF module, mSATA, or other I/O dongle.
■ Support 12V \~ 24V wide voltage DC input.
One-Stop Integrated Solution: Integrated ultra compact motherboard, chassis, peripherals and software
■ Dimensions: 152 x 128 x 37.1 mm

1.2 System Configuration

The following diagram is a block drawing of the UTX-3117.

graph TD
    A["Intel Apollo Lake N4200/E39xx SoC TDP:5.5~13W"] -->|DDI| B["DDR3L Non-LCC 1333/1600/1867 MHz, up to 8G"]
    A -->|DDI| C["GbE 1: I211AT"]
    A -->|DDI| D["GbE 2: RTL8111G"]
    A -->|600MBs| E["1 SATA 3.0"]
    A -->|USB3.0| F["2 USB3.0"]
    A -->|HD AUDIO| G["ALC892, Line out/MIC in"]
    A -->|USB2.0| H["PCIE x1 USB2.0"]
    A -->|PCIE x1| I["Super I/O NCT5523D"]
    I --> J["TPM Inlineon SLB9660"]
    I --> K["1 RS-232 1 RS-422/485 8bit GPIO WDT H/W monitor"]
    style A fill:#f9f,stroke:#333
    style B fill:#9cf,stroke:#333
    style C fill:#9cf,stroke:#333
    style D fill:#9cf,stroke:#333
    style E fill:#9cf,stroke:#333
    style F fill:#9cf,stroke:#333
    style G fill:#9cf,stroke:#333
    style H fill:#9cf,stroke:#333
    style I fill:#9cf,stroke:#333
    style J fill:#9cf,stroke:#333
    style K fill:#9cf,stroke:#333

Button I/O arrangement:

USB 3.0 LAN DP HDD LED HDMI Power Bu on WSN ANT Audio Jack RS-485/422 RS-422/485 RS-232 12-24V DC IN

1.3 General Specifications

1.3.1 Standard PC Functions

CPU: Intel® Atom™ E3900 series, Pentium N4200, Celeron N3350 SoC.
BIOS: AMI EFI 16bit
■ Memory: DDR3L SODIMM 1333/1866 MHz up to 8GB
■ Audio: HD audio codec ALC892
■ LAN: PCI-E gIGABIT Ethernet controllers x2
LAN1: Intel i210AT; LAN2: RTL8111G
■ Universal serial bus (USB) port: 2 USB3.0
Mini PCI-E bus expansion slot: 1 F/S miniPCIE support 3G/LTE card; 1 H/S miniPCIE support mSATA/WIFI card, 1 M.2 E-key support WiFi card.
■ Storage housing: 1 2.5" slim SSD
■ Audio output: Combo Audio Jack
■ Video output: 1 HDMI, 1 Display port

1.3.2 Power Environmental

■ Power adaptor: AC/DC
- Input voltage: 100 Vac \~ 240 Vac @ 50 - 60 Hz,1.5
A - Output voltage: 12 V @ 3 A\~24V @ 3A

1.4 Mechanical Specifications

1.4.1 Mechanical Specifications (Terminal)

■ System Dimensions: 152 X 128 X 37.1 mm (5.98" X 5.2" X 1.46")

Diagram of a heat exchanger or cooling unit with vertical slats and control panel (no text or symbols)

Carton Dimensions: 255 (L) X 235 (W) X 160 (H) mm
■ Gross Weight: 2.0 kg
■ Net Weight: 1.8 kg

1.5 Environmental Specifications

Temperature & Humidity

• Operating Temperature: -20 \~ 60 °C (with RF module)
  ■ Storage Temperature: -40 \~ 60°C
  ■ Relative Humidity: 40 \~ 95% RH (Non-condensed)

Safety

CE / UL/CB/CCC/BSMI

EMI

■ FCC class B approved for USA, Canada, and EU

Vibration:

■ With SSD: 3Grms, 60068-2-64, random, 5 \~ 500 Hz, 1 hr/axis

Chapter 2

Jumper and Connector List

2.1 Connectors & Jumpers

(1) (2) (3)

Figure 2.1 Top View

(4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (1) ADVANTECH E:\MRO ADMA1 ADMA2 ADMA3 ADMA4 ADMA5 ADMA6 ADMA7 ADMA8 ADMA9 ADMA10 ADMA11 ADMA12 ADMA13 ADMA14 ADMA15 ADMA16 ADMA17 ADMA18 ADMA19 ADMA20 ADMA21 ADMA22 ADMA23 ADMA24 ADMA25 (2) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25)

Figure 2.2 Bottom View

Connector and Header List:

(1) CPU-System on chip(SOC1)
(2) BIOS Flash(SPI1)
(3) DDR3LSO-DIMM Socket (DIMMA1)
(4) DC input Connector (DCIN1)
(5) MINIPCIE Connector (MINI-PCIE1)
(6) SIM Card Socket (SIM1)
(7) Low Pin Count Header (LPC1)
(8) MINIPCIE and mSATA Connector (MINI-PCIE2)
(9) SPI Programming Pin Header(SPI_CN1)
(10) COM Port(COM1)
(11) General Purpose I/O Pin Header (GPIO1)
(12) HDAnalog Audio Interface(AUDIO1)
(13) COM Port(COM2)
(14) Next Generation Form Factor (M.2_1)
(15) SATA Signal Connector (SATA1)
(16) USB 3.0 Connector(USB1)
(17) SATA Power Connector (SATA_PWR1)
(18) USB 3.0 Connector(USB2)
(19) RJ45 Connector(LAN2)
(20) RJ45 Connector(LAN1)
(21) High Definition Multimedia Interface(HDMI1)
(22) DisplayPort(DP1)
(23) DDR3LSO-DIMM Socket (DIMMB1)

(24) SATA LED(D10)
(25) Power Button(PWRBTN1)

Jumper List:

(1) RS485/RS422 selection pin header (J485/422)

Table 2.1: RS485/RS422selection pin header (J485/422)

Function Setting
RS485 (Default)		1 and 2
RS232		2 and 3

Table 2.2: AT/ATX Mode Selection (PSON1)

Function Setting
AT Mode		1 and 2
ATX Mode (Default)		2 and 3

2.2 Connectors

2.2.1 CPU-System on chip(SOC1)

TOP VIEW SECTION A-A

2.2.2 BIOS Flash(SPI1)

Pure electrical circuit symbol for an integrated resistor (no text or labels)

Pin	Signal	Pin	Signal
1	SPI_Z_CS0	6	SPI_Z_CLK
2	SPI_Z_MISO	7	SPI_Z_IO3
3	SPI_Z_IO2	8	+V1.8SB_SPI
4 GND
5 SPI_Z_MOSI

2.2.3 DDR3L SO-DIMM Socket (DIMMA1)

3D illustration of a cyan mechanical component with attached wires and connectors, showing internal structure (no text or symbols)

2.2.4 DC input Connector(DCIN1)

12.5±0.3 3.0 +0.1 45.6-0 +0.2 26-0 0.25t

(12.7) 11.0 5.5 3.2 R0.8 Ø2.45 1.6

20.2 8.5 8.65 M8.0X0.75 18.1 2.1 3 1 3.6 3.6 21

BOTTOM VIEW

REAR VIEW

Pin Signal

1 Power input

2 GND

3 GND

2.2.5 MINIPCIE Connector (MINI-PCIE1)

Isometric technical drawing of a 25-pin integrated circuit package with labeled pins (no text or symbols beyond labels)

MINIPCIE:

Pin	Signal	Pin	Signal
1	WAKE#	2	+3.3Vaux
3	Reserved	4	GND
5	Reserved	6	+1.5V
7	Reserved	8	SIM_VCC1
9	GND	10	SIM_IO1
11	Reserved	12	SIM_CLK1
13	Reserved	14	SIM_RST1
15	GND	16	SIM_SPU1
17	Reserved	18	GND
19	Reserved	20	DISABLE#
21	GND	22	RESET#
23	Reserved	24	+3.3Vaux
25	Reserved	26	GND
27	GND	28	+1.5V
29	GND	30	Reserved
31	Reserved	32	Reserved
33	MINI-PCIE1 _RESET#	34	GND
35	GND	36	USB_D-
37	GND	38	USB_D+
39	+3.3Vaux	40	GND
41	+3.3Vaux	42	Reserved
43	Reserved	44	Reserved
45	Reserved	46	Reserved
47	Reserved	48	+1.5V
49	Reserved	50	GND
51	Reserved	52	+3.3Vaux

2.2.6 SIM Card Socket (SIM1)

(Ø3.0Max.)Vacuum area 9.10 17.95 OPEN 127PIICH 127 15.30 1220±0.10 7.65 6.10 A HV 1.30 0.95 127±0.35 0.30±0.05 0.60±0.05 1.80±0.10 7.62(REF.) SECTION A-A'

Pin	Signal	Pin	Signal
C1	SIM_VCC1	H1	GND
C2	SIM_RST1	H2	GND
C3	SIM_CLK1	H3	GND
C5	GND	H4	GND
C6 SIM_SPU1

2.2.7 Low Pin Count Header (LPC1)

Pin	Signal	Pin	Signal
1	SOC_LPC_AD1	2	CLKOUT_25M_LPC
3	SOC_LPC_AD0	4	PM_PLTRST#
5	+V3.3	6	SOC_LPC_FRAME#
7	GND	8	SOC_LPC_AD3
9	X	10	SOC_LPC_AD2

2.2.8 MINIPCIE and mSATA Connector (MINI-PCIE2)

Technical line drawing of an electronic component with labeled pins (no text or symbols beyond labels)

MINIPCIE:

Pin	Signal	Pin	Signal
1	WAKE#	2	+3.3Vaux
3	Reserved	4	GND
5	Reserved	6	+1.5V
7	CLKREQ#	8	Reserved
9	GND	10	Reserved
11	REFCLK-	12	Reserved
13	REFCLK+	14	Reserved
15	GND	16	Reserved
17	Reserved	18	GND
19	Reserved	20	DISABLE#
21	DETECT#	22	RESET#
23	PCIE_RX+	24	+3.3Vaux
25	PCIE_RX-	26	GND
27	GND	28	+1.5V
29	GND	30	SMB_CLK
31	PCIE_TX-	32	SMB_DATA
33	PCIE_TX+	34	GND
35	GND	36	USB_D-
37	GND	38	USB_D+
39	+3.3Vaux	40	GND
41	+3.3Vaux	42	Reserved
43	V1.2_DETECT#	44	LED_WLAN#
45	Reserved	46	Reserved
47	Reserved	48	+1.5V
49	Reserved	50	GND
51	MSATA_DETECT#	52	+3.3Vaux

mSATA:

Pin	Signal	Pin	Signal
1	Reserved	2	+3.3V
3	Reserved	4	GND
5	Reserved	6	+1.5V
7	Reserved	8	Reserved
9	GND	10	Reserved
11	Reserved	12	Reserved
13	Reserved	14	Reserved
15	GND	16	Reserved
17	Reserved	18	GND
19	Reserved	20	Reserved
21	DETECT#	22	Reserved
23	RX+	24	+3.3V
25	RX-	26	GND
27	GND	28	+1.5V
29	GND	30	SMB_CLK
31	TX-	32	SMB_DATA
33	TX+	34	GND
35	GND	36	Reserved
37	GND	38	Reserved
39	+3.3V	40	GND
41	+3.3V	42	Reserved
43	Reserved	44	Reserved
45	Reserved	46	Reserved
47	Reserved	48	+1.5V
49	Reserved	50	GND
51	MSATA_DETECT#	52	+3.3V

2.2.9 SPI Programming Pin Header (SPI\_CN1)

Pin	Signal	Pin	Signal
1	CS#	2	+3.3V
3	MISO	4	X
5	X	6	SCK
7	GND	8	MOSI

2.2.10 COM Port (COM1)

Pin	Signal	Pin	Signal
1	DCD#	6	DSR#
2	RXD	7	RTS#
3	TXD	8	CTS#
4	DTR#	9	RI#
5 GND

2.2.11 General Purpose I/O Pin Header (GPIO1)

1 3 5 7 9 2 4 6 8 10

Pin	Signal	Pin	Signal
1	GPIO0	2	GPIO4
3	GPIO1	4	GPIO5
5	GPIO2	6	GPIO6
7	GPIO3	8	GPIO7
9	+3.3V	10	GND

2.2.12 HD Analog Audio Interface (AUDIO1)

DATE CODE YMMDB 9.50 0.08 14.90 2.90 R0.20

2-0.75 Ø3,60±0.04 Ø6.00 8-1.2 3.30 2.40

Pin	Signal	Pin	Signal
1	CONN_FRONT_L	6	GND_A
2	CONN_FRONT_R	MS1	GND_A
3	GND_A	MS2	GND_A
4	CONN_MIC1_L	H1	x
5	FRONT_SENSE_A	H2	x

2.2.13 COM Port (COM2)

Diagram of a five-pin electrical connector with pins and a pinout indicator (no text or symbols)

Pin	Signal
1	COM2_422_485_TX-
2	COM2_422_485_TX+
3	GND
4	COM2_422_RX-
5	COM2_422_RX+

2.2.14 Next Generation Form Factor (M.2\_1)

21.85 LOTES XXXXXX D/C E 5.90±0.15 1.10±0.05 -X-

Pin	Signal	Pin	Signal
1	GND	43	PCIE_RX3-
2	+V3.3SB_M.2	44	x
3	USB_D4+	45	GND
4	+V3.3SB_M.2	46	x
5	USB_D4-	47	CK100M_NGFF+
6	x	48	x
7	GND	49	CK100M_NGFF-
8	NGFF_I2S3_Z_BCLK	50	NGFF_PMU_SUSCLK
9	SDIO_WIFI_CLK	51	GND
10	NGFF_I2S3_Z_SYNC	52	NGFF_PLTRST#
11	SDIO_WIFI_CMD	53	PCIE_REQ2_NGFF#
12	NGFF_I2S3_Z_SDI	54	NGFF_BT_DISABLE#
13	SDIO_WIFI_D0	55	PCIE_NGFF_WAKE2#
14	NGFF_I2S3_Z_SDO	56	NGFF_WIFI_DISABLE#
15	SDIO_WIFI_D1	57	GND
16	x	58	x
17	SDIO_WIFI_D2	59	x
18	GND	60	x
19	SDIO_WIFI_D3	61	x
20	NGFF_CONN_UART_WAKE#	62	x
21	SDIO_WIFI_WAKE#	63	GND
22	NGFF_UART0_Z_RXD	64	x
23	SDIO_WIFI_RST	65	x
32	NGFF_UART0_Z_TXD	66	x
33	GND	67	x
34	NGFF_UART0_Z_CTS#	68	x
35	NGFF_PCIE_TX3+	69	GND
36	NGFF_UART0_Z_RTS#	70	x
37	NGFF_PCIE_TX3-	71	x
38	x	72	+V3.3SB_M.2
39	GND	73	x
40	x	74	+V3.3SB_M.2
41	PCIE_RX3+	75	GND
42	x

2.2.15 SATA Signal Connector (SATA1)

12.74 0.45 0.36 3.15 11.50 1.27 TYP 7.62 0.84±0.05

4.25 SECT B-B

Pin	Signal	Pin	Signal
1	GND	6	SATA0_Z_RX+
2	SATA0_Z_TX+	7	GND
3	SATA0_Z_TX-	8	x
4	GND	9	x
5	SATA0_Z_RX-	6	SATA0_Z_RX+

2.2.16 USB 3.0 Connector(USB1)

2.2.17 USB 3.0 Connector(USB2)

Technical line drawing of a mechanical device with no visible text or symbols

Pin	Signal	Pin	Signal
1	+USBV1	7	GND
2	USB_D0-	8	USB3X0_Z_TX-
3	USB_D0+	9	USB3X0_Z_TX+
4	GND	H1	GND_F1
5	USB3X0_Z_RX-	H2	GND_F1
6	USB3X0_Z_RX+		x

2.2.18 SATA Power Connector (SATA\_PWR1)

Pin	Signal	Pin	Signal
1	+V5	3	GND
2	GND	4	x

2.2.19 RJ45 Connector(LAN1)

2.2.20 RJ45 Connector(LAN1)

LEFT LED 11.90 +0.05 -0.10 RIGHT LED C8 C1 6.80 +0.05 -0.10 11.45 ±0.38 18.60 ±0.38

23.75 ±0.38 0.50 7.75 1.8 0.35 1.20 11.96 9.64 13.16 1.27

RJ45

Pin	Signal	Pin	Signal
R1	LAN2_TCT	R10	LAN2_MDI3-
R2	LAN2_MDI0+	R11	LAN1_TCT
R3	LAN2_MDI0-	H1	GND_LAN
R4	LAN2_MDI1+	H2	GND_F1
R5	LAN2_MDI1-	L1	LAN2_LED1_Z_ACT#
R6	LAN2_TCTG	L2	+V3.3_LAN2
R7	LAN2_MDI2+	L3	LAN2_LED2_Z_1G#
R8	LAN2_MDI2-	L4	LAN2_LED0_Z_100M#

2.2.21 High Definition Multimedia Interface(HDMI1)

SCREW HOLE SHELL TERMINAL HOLDING

Pin	Signal	Pin	Signal
1	HDMI1_Z_D2+	11	GND
2	GND	12	HDMI1_Z_CLK-
3	HDMI1_Z_D2-	13	x
4	HDMI1_Z_D1+	14	x
5	GND	15	HDMI1_SCL
6	HDMI1_Z_D1-	16	HDMI1_SDA
7	HDMI1_Z_D0+	17	GND
8	GND	18	+V5_HDMI
9	HDMI1_Z_D0-	19	HDMI1_HPD
10	HDMI1_Z_CLK+

2.2.22 DisplayPort (DP1)

Technical line drawing of an electronic component with multiple slots and housing (no text or symbols)

Pin	Signal	Pin	Signal
1	DP1_0+	11	GND
2	GND	12	DP1_3-
3	DP1_0-	13	DP1_AUX_EN#
4	DP1_1+	14	GND
5	GND	15	DP1_AUX+
6	DP1_1-	16	GND
7	DP1_2+	17	DP1_AUX-
8	GND	18	DP1_DP_HPD
9	DP1_2-	19	GND
10	DP1_3+	20	+V3.3_DP1

2.2.23 DDR3L SO-DIMM Socket (DIMMB1)

PIN2 1.5V H=5.2A LOTES PIN204

2.2.24 SATA LED(D10)

4.5±0.5 2.0±0.3 3.0±0.3 3.2±0.2 3.5±0.5 9.2±0.3 3.0 6.0±0.5 Ø1.4 5.4±0.5 3.1±0.3 PIN1 PIN2 2.54±0.5

LED PIN1.anode (yellow) PIN2.cathode

2.2.25 Power Button(PWRBTN1)

Technical line drawing of a mechanical assembly with top and side views (no text or symbols)

Chapter 3

Peripheral Installation

3.1 HDD Installation

1. Unscrew the bottom cover screws.

1. Secure 2.5" SATA HDD onto the bottom cover. The screws are in the accessory box.

Transcend® Solid State Drive

1. Connect SATA signal and power cable to the 2.5" SATA HDD.

Interior view of an electronic device showing a battery pack, circuit board, and wiring (no readable text or symbols)

1. Secure the bottom cover in its original position.

1. Unscrew the bottom cover screws.

KSE0109380 Open Open Open Open WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN

1. Insert Mini PCIe module into the slot and secure the screw to fix the module.

Interior view of an electronic device showing internal components like circuit boards, capacitors, and wires (no readable text or symbols)

1. Connect the antenna cable to module.

Interior view of an electronic device showing internal components like circuit boards, capacitors, and wiring (no readable text or symbols)

1. Secure the bottom cover in its original position.

AMI BIOS has been integrated into many, many motherboards for decades. With the AMI BIOS Setup program, users can modify BIOS settings and control various system features. This chapter describes the basic navigation of the UTX-3117 BIOS setup screens.

AMI's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in flash ROM so it retains the Setup information when the power is turned off.

Note!

Default BIOS is supported for 64-bit OS installation, if you have any BIOS setting requirement, please contact with sales representative for details.

Control Keys

<↑><↓><←>Move select item
	Select item
	Main Menu - Quit without saving changes to the CMOSSub Menu - Exit current page and return to the Main Menu
	Increase the numeric value or make changes
	Decrease the numeric value or make changes
	General help, for Setup Sub Menu
	Item help
	Load previous values
	Load setup defaults
	Save all CMOS changes

4.2 Entering Setup

4.2.1 Main Menu

Press to enter AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. Use arrow keys to select among the items and press to accept or enter the sub-menu.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit BIOS Information BIOS Vendor American Megatrends Core Version 5.0.1.2 0.26 x64 Compliancy UEFI 2.5: PI 1.4 Project Version A1170000F60X040 Build Date and Time 07/20/2017 11:44:54 Access Level Administrator Project Board Version AIM8-117 Power Type ATX Memory Information Total Memory 2048 MB Memory Speed 1600 MHz System Date [Tue 10/24/2017] System Time [14:12:26] Set the Date. Use Tab to switch between Date elements. Default Ranges: Year: 2005-2099 Months: 1-12 Days: dependent on month ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

The Main BIOS setup screen has two main frames. The left frame displays all the options that can be configured. Grayed-out options cannot be configured; options in blue can. The right frame displays the key legend.

Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it.

System time / System date

Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard. Press the key or the keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format.

4.2.2 Advanced BIOS Features

Select the Advanced tab from the UTX-3117 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
Realtek PCIe GBE Family Controller (MAC:00:00:C9:E9:7C:C4) Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... Trusted Computing ACPI Settings NCT5523D Super IO Configuration Hardware Monitor SS RTC Wake Settings Serial Port Console Redirection CPU Configuration Network Stack Configuration CSM Configuration NVMe Configuration USB Configuration Platform Trust Technology Security Configuration	Get driver Information and configure Realtek ethernet controller parameter
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

4.2.2.1 Realtek PCIe GBE Family Controller Status

Check the status of Realtek LAN port.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Driver Information Driver Name: Realtek UEFI UNDI Dri... Driver Version: 2.035 Driver Released Date: 2015/03/30 Device Information Device Name: Realtek PCIe GBE Fami... PCI Slot: 01:00:00 MAC Address: 00:0D:C9:E9:7C:C4 Patent Information This product is covered by one or US6,570,884, US6,115,776, and US6, ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

4.2.2.2 Check Intel® I201 Gigabit Network connection Status

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced NIC Configuration Blink LEDs 0 UEFI Driver Intel(R) PRO/1000 6.8... Adapter PBA 000200-000 Device Name Intel(R) I210 Gigabit... Chip Type Intel i210 PCI Device ID 1533 PCI Address 02:00:00 Link Status [Disconnected] MAC Address 00:0B:AB:8F:8D:89 Virtual MAC Address 00:00:00:00:00:00 Click to configure the network device port. ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Link Speed [Auto Negotiated] Make On LAN [Enabled] Specifies the port speed used for the selected boot protocol. +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

4.2.2.3 Trusted Computing

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... ►Trusted Computing ►ACPI Settings ►NCTS523D Super IO Configuration ►Hardware Monitor ►S5 RTC Make Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►DSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	Trusted Computing Settings
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

■ Security Device Support

Enable or disable BIOS support for security device.

TPM20 Device Found Security Device Support [Enable] Active PCR banks SHA-1 Available PCR banks SHA-1,SHA256		Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
Pending operation Platform Hierarchy Storage Hierarchy Endorsement Hierarchy TPM2.0 UEFI Spec Version Physical Presence Spec Version TPM 20 InterfaceType Device Select	[Enabled] [Disabled] [None] [Enabled] [Enabled] [Enabled] [TCG_2] [1.2] [TIS] [Auto]

4.2.2.4 APCI Settings

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... Trusted Computing ACPI Settings NCTS523D Super IO Configuration Hardware Monitor S5 RTC Wake Settings Serial Port Console Redirection CPU Configuration Network Stack Configuration CSM Configuration NVMe Configuration USB Configuration Platform Trust Technology Security Configuration	System ACPI Parameters.
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced ACPI Settings Enable ACPI Auto Configuration [Disabled] Enable Hibernation [Enabled] ACPI Sleep State [S3 (Suspend to RAM)] Lock Legacy Resources [Disabled] Enables or Disables BIOS ACPI Auto Configuration. +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit ++: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

■ Enable ACPI Auto Configuration
Enable or disable BIOS ACPI auto configuration.
■ Enable Hibernation
This item allows users to enable or disable hibernation.
ACPI Sleep State
This item allows users to set the ACPI sleep state.
■ Lock Legacy Resource
This item allows users to lock legacy device resources.

4.2.2.5 NCT5523D Super IO Configuration

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... Trusted Computing ACPI Settings NCT5523D Super IO Configuration Hardware Monitor S5 RTC Wake Settings Serial Port Console Redirection CPU Configuration Network Stack Configuration CSM Configuration NVMe Configuration USB Configuration Platform Trust Technology Security Configuration	System Super IO Chip Parameters.
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced NCT5523D Super IO Configuration Super IO Chip NCT5523D ► Serial Port 1 Configuration ► Serial Port 2 Configuration Set Parameters of Serial Port 1 (COMA) ++ : Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Serial Port 1 Configuration Serial Port [Enabled] Device Settings IO=3F8h: IRQ=4; Change Settings [Auto] Enable or Disable Serial Port (COM) +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Serial Port 1&2 Configuration

This item allows users to enable or disable serial Ports 1/2

Change Settings

This item allows users to change the serial port 1/2

4.2.2.6 Hardware Monitor

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:0B:AB:BF:... ►Trusted Computing ►ACPI Settings ►NCT5523D Super IO Configuration ►Hardware Monitor ►S5 RTC Wake Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►CSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	Monitor hardware status
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Pc Health Status SYSTEM Temperature : +38°C CPU Temperature : +42°C VCORE : +0.744 V VIN2 : +4.978 V VCC3V : +3.280 V VSB3V : +3.200 V VBAT : +3.152 V AVSB : +3.296 V Digital I/O Configuration Wake On Ring [Disabled] RS485 AUTO FLOW [Disabled] ACPI Shutdown Temperature [Disabled] Configure the digital I/O pins +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

This item allows you to monitor HW status

■ Execute Disable Bit

This item allows users to enable or disable the No-Execution page protection.

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

Optio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Digital I/O Configuration Digital I/O Pin 1 [Input] Digital I/O Pin 2 [Input] Digital I/O Pin 3 [Input] Digital I/O Pin 4 [Input] Digital I/O Pin 5 [Input] Digital I/O Pin 6 [Input] Digital I/O Pin 7 [Input] Digital I/O Pin 8 [Input] Configure Digital I/O Pin. ++ : Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

■ Digital I/O Configuration

This item will allow users to set up Digital I/O 1\~8 to "input" or "output".

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit ► Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ► Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... ► Trusted Computing ► ACPI Settings ► NCT5523D Super IO Configuration ► Hardware Monitor ► S5 RTC Wake Settings ► Serial Port Console Redirection ► CPU Configuration ► Network Stack Configuration ► CSM Configuration ► NVMe Configuration ► USB Configuration ► Platform Trust Technology ► Security Configuration Enable system to wake from S5 using RTC alarm +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Make system from S5 [Disabled] Enable or disable System wake on alarm event. ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Wake System From S5

Enable or disable system wake on alarm event.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit ► Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ► Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... ► Trusted Computing ► ACPI Settings ► NCT5523D Super IO Configuration ► Hardware Monitor ► S5 RTC Wake Settings ► Serial Port Console Redirection ► CPU Configuration ► Network Stack Configuration ► CSM Configuration ► NVMe Configuration ► USB Configuration ► Platform Trust Technology ► Security Configuration Serial Port Console Redirection +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced COM1 Console Redirection [Disabled] ► Console Redirection Settings Legacy Console Redirection ► Legacy Console Redirection Settings Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection [Disabled] ► Console Redirection Settings Console Redirection Enable or Disable. +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Legacy Serial Redirection Port [COM1] Select a COM port to display redirection of Legacy OS and Legacy OPROM Messages +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

■ Console Redirection

This item allows users to enable or disable console redirection.

4.2.2.7 CPU Configuration

This page shows CPU Information.

CPU Configuration Socket 0 CPU Information		Socket specific CPU Information
Speed 64-bit	1100 MHz Supported
CPU Power Management Active Processor Cores Intel Virtualization Technology VT-d Bi-directional PROCHOT Thermal Monitor Monitor Mwait P-STATE Coordination	[Disabled] [Enabled] [Disabled] [Enabled] [Auto] [HW_ALL]
		+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Active Power Cores

Number of cores to enable in each processor package

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

VT-d

Enable or disable VT-d

Bi-directional PROCHOT

When a processor thermal sensor trips (either core), the PROCHOT# will be driven. If bi-direction is enabled, external agents can drive PROCHOT# to throttle the processor.

Thermal Monitor

Enable or disable Thermal Monitor

Monitor Mwait

Enable/disable Monitor Mwait.

P-STATE Coordination

Change P-STATE Coordination type.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Socket O CPU Information Intel(R) Pentium(R) CPU N4200 @ 1.10GHz CPU Signature 506C9 Microcode Patch 28 Max CPU Speed 1100 MHz Min CPU Speed 800 MHz Processor Cores 4 Intel HT Technology Not Supported Intel VT-x Technology Supported L1 Data Cache 24 kB x 4 L1 Code Cache 32 kB x 4 L2 Cache 1024 kB x 2 L3 Cache Not Present ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced CPU Configuration Socket O CPU Information Speed 1100 MHz 64-bit Supported CPU Power Management Active Processor Cores [Disabled] Intel Virtualization Technology [Enabled] VT-d [Disabled] Bi-directional PROCHOT [Enabled] Thermal Monitor [Enabled] Monitor Mwait [Auto] P-STATE Coordination [HH_ALL] CPU Power Management options +: Select Screen ↑: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

CPU Power Management Configuration EIST [Enabled] Turbo Mode [Enabled] Boot performance mode [Max Performance] C-States [Enabled] Enhanced C-states [Enabled] Max Package C State [PC2] Max Core C State [Fused value] C-State Auto Demotion [C1] C-State Un-demotion [C1] Power Limit 1 Enable [Enabled] Power Limit 1 Power Limit 1 Clamp Mode [Enabled] Power Limit 1 Power [Auto] Power Limit 1 Time Window [Auto]

Enable/Disable Intel SpeedStep

+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

EIST

Enabled or disabled Intel Speed Step function.

Turbo Mode

Enabled or disabled Turbo Mode

■ Boot performance mode

Select the performance state that the BIOS will set before OS handoff.

C-States

Enabled or disabled C-States

■ Enhanced C-States

Enabled or disabled C1E. When enabled, CPU will switch to minimum speed when all cores enter C-State.

■ Max Package C State

Controls the max package C state that the processor will support.

■ Max Core C State

This option controls the Max Core C State that cores will support.

C-State Auto Demotion

Configure C-State Auto Demotion.

C-State Un-Demotion

Configure C-State Un-demotion.

Power Limit 1 Enable

Enable/Disable Power Limit 1.

Power Limit 1 Clamp Mode

Enable/Disable Power Limit 1 Clamp Mode.

Power Limit 1 Power

Power Limit 1 in Watts. Auto will program Power Limit 1 based on silicon default support value.

Power Limit 1 Time Window

Power Limit 1 Time Window Value in seconds. Auto will program Power Limit 1 Time Window based on silicon default support value.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... ►Trusted Computing ►ACPI Settings ►NCTSS23D Super IO Configuration ►Hardware Monitor ►S5 RTC Wake Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►CSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	Network Stack Settings
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Network Stack [Disabled] Enable/Disable UEFI Network Stack +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Network Stack

Enable or disable UEFI Network Stack.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... ►Trusted Computing ►ACPI Settings ►NCT5523D Super IO Configuration ►Hardware Monitor ►SS RTC Make Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►CSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	CSM configuration: Enable/Disable, Option ROM execution settings, etc.
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced Compatibility Support Module Configuration CSM Support [Disabled] Enable/Disable CSM Support. ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

CSM Support

Enable or disable CSM Support..

4.2.2.8 NVMe Configuration

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:0B:AB:BF:... ►Trusted Computing ►ACPI Settings ►NCTS523D Super IO Configuration ►Hardware Monitor ►S5 RTC Wake Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►CSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	NVMe Device Options Settings
	++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced NVMe controller and Drive information No NVME Device Found +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263, Copyright (C) 2017 American Megatrends, Inc.

4.2.2.9 USB Configuration

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... Trusted Computing ACPI Settings NCT5523D Super IO Configuration Hardware Monitor SS RTC Wake Settings Serial Port Console Redirection CPU Configuration Network Stack Configuration CSM Configuration NVMe Configuration USB Configuration Platform Trust Technology Security Configuration	USB Configuration Parameters
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced
USB Configuration USB Module Version 17 USB Controllers: 1 XHCI USB Devices: 1 Drive, 1 Keyboard Legacy USB Support [Enabled] XHCI Hand-off [Enabled] USB Mass Storage Driver Support [Enabled]	Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
USB hardware delays and time-outs: USB transfer time-out [20 sec] Device reset time-out [20 sec] Device power-up delay [Auto]	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Mass Storage Devices: JetFlashTranscend 32GB 1100 [Auto]
Version 2,18,1263. Copyright (C) 2017 American Megatrends, Inc.

■ Legacy USB Support

Enables support for legacy USB. Auto option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

XHCI Hand-Off

This is a workaround for OS without XHCI hand-off support. The XHCI ownership change should claim by XHCI driver.

USB Mass Storage Driver Support

This item allows you to enable or disable the USB mass storage device support.

USB transmit time-out

USB mass storage device transmit command time-out.

■ Device reset time-out

USB mass storage device start unit command time-out.

■ Device power-up delay

Maximum time the device will take before it properly reports itself to the host controller. "Auto" uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor.

Mass storage device

Mass storage device emulation type. 'AUTO' enumerates devices according to their media format. Optical drives are emulated as 'CDROM', drives with no media will be emulated according to a drive type.

4.2.2.10 Platform Trust Technology

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:08:AB:BF:... ►Trusted Computing ►ACPI Settings ►NCT5523D Super IO Configuration ►Hardware Monitor ►S5 RTC Wake Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►CSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	Platform Trust Technology
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced TPM Configuration +TPM [Disabled] Enable/Disable fTPM +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

fTPM

Enabled or disabled fTPM.

4.2.2.11 Security Configuration

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
►Realtek PCIe GBE Family Controller (MAC:00:0D:C9:E9:7C:C4) ►Intel(R) I210 Gigabit Network Connection - 00:0B:AB:8F:... ►Trusted Computing ►ACPI Settings ►NCT5523D Super IO Configuration ►Hardware Monitor ►S5 RTC Wake Settings ►Serial Port Console Redirection ►CPU Configuration ►Network Stack Configuration ►CSM Configuration ►NVMe Configuration ►USB Configuration ►Platform Trust Technology ►Security Configuration	Intel(R) Anti-Theft Technology Configuration
	+: Select Screen 11: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Advanced TXE HMRFP0 [Disabled] TXE EOP Message [Enabled] ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

TXE HMRFPO

This item allows users to enable or disable TXE HMRFPO.

■ TXE EOP Message

Send EOP Message before Enter OS.

4.2.3 Chipset

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit North Bridge South Bridge Uncore Configuration South Cluster Configuration North Bridge Parameters +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

4.2.3.1 North Bridge

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit North Bridge South Bridge Uncore Configuration South Cluster Configuration North Bridge Parameters +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Chipset
Memory Information Total Memory 2048 MB (LPDDR3) Memory DIMMA1 Not Present Memory DIMMB1 2048 MB (LPDDR3) Max TOLUD [2 GB] PCIE VGA Workaround [Disabled]	Maximum Value of TOLUD.
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit ► North Bridge ► South Bridge ► Uncore Configuration ► South Cluster Configuration South Bridge Parameters ++ +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Chipset OS Selection [Windows] Select the target OS. ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

OS Selection

Select the target OS.

4.2.3.2 Uncore Configuration

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit ► North Bridge ► South Bridge ► Uncore Configuration ► South Cluster Configuration Uncore Configuration +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

IGD ConfigurationIntegrated Graphics Device [Enable]Primary Display [IGO]RC6 (Render Standby) [Enable]GTT Size [8MB]Aperture Size [256MB]DVMT Pre-Allocated [64M]DVMT Total Gfx Mem [256M]Cd Clock Frequency [624 MHz]GT PM Support [Enable]PAVP Enable [Enable]Memory Configuration Memory Scrambler [Disable]

Enable : Enable Integrated Graphics Device (IGD) when selected as the Primary Video Adaptor. Disable: Always disable IGO++: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save & ExitESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
North BridgeSouth BridgeUncore ConfigurationSouth Cluster Configuration	South Cluster Configuration
	++: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save & ExitESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Chipset PCI Express Configuration SATA Drives LAN1 Control [Enable] LAN2 Control [Enable] HD-Audio Support [Enable] High Precision Timer [Enable] Restore AC Power Loss [Power Off] BIOS Lock [Enabled] RTC Lock [Enabled] Flash Protection Range Registers ( [Enabled] PCIE Make [Disable] Press to select the SATA Device Configuration Setup options. +: Select Screen +: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Chipset SATA

Enables or disables the chipset SATA controller. The chipset SATA controller supports the 2 black internal SATA ports (up to 3Gb/s supported per port).

■ SATA Mode Selection

This item allows users to select mode of SATA controller(s).

■ Aggressive LPM Support

This item allows users to enable or disable Aggressive LPM Support.

Port 1

This item allows users to enable or disable the Serial-ATA Port 1 device.

Spin Up Device

This item allows users to enable or disable the Spin Up Device.

SATA Device Type

Identify the SATA port is connected to Solid State Drive or Hard Disk Drive.

Port 2

This item allows users to enable or disable the Serial-ATA Port 2 device

Spin Up Device

This item allows users to enable or disable the Spin Up Device.

■ SATA Device Type

Identify the SATA port is connected to Solid State Drive or Hard Disk Drive.

PCI Express Configuration PCI Express Clock Gating [Enabled] Compliance Mode [Disabled] ► Mini PCIE ► M.2	Control the PCI Express Root Port. AUTO: To disable unused root port automatically for the most optimum power savings. Enable: Enable PCIe root port Disable: Disable PCIe root port
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Chipset
Mini PCIE If DISABLED, goto ENABLE first the ASPM L1 Substates PCIe Speed	[Enable] [Auto] [L1.1 & L1.2] [Auto]
	Control the PCI Express Root Port. AUTO: To disable unused root port automatically for the most optimum power savings. Enable: Enable PCIe root port Disable: Disable PCIe root port
	++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Version 2.18.1253. Copyright (C) 2017 American Megatrends, Inc.
PCI Express Configuration PCI Express Clock Gating [Enabled] Compliance Mode [Disabled]	Control the PCI Express Root Port. AUTO: To disable unused root port automatically for the most optimum power savings. Enable: Enable PCIe root port Disable: Disable PCIe root port
Mini PCIE M.2
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Chipset M.2 [Auto] If DISABLED, goto ENABLE first the ASPM [Disable] L1 Substates [Disabled] PCIe Speed [Auto] Control the PCI Express Root Port. AUTO: To disable unused root port automatically for the most optimum power savings. Enable: Enable PCIe root port Disable: Disable PCIe root port +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

SATA Drives Chipset-SATA Controller Configuration Chipset SATA [Enable] SATA Mode Selection [AHCI] Aggressive LPM Support [Enabled] SATA Port 1 [Not Installed] Port 1 [Enabled] Spin Up Device [Disabled] SATA Device Type [Hard Disk Drive] mSATA Port [Not Installed] mSATA [Enabled] Spin Up Device [Disabled] SATA Device Type [Hard Disk Drive]	Enables or Disables the Chipset SATA Controller. The Chipset SATA controller supports the 2 block Internal SATA ports (up to 3Gb/s supported per port). ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Version 2,18,1263. Copyright (C) 2017 American Megatrends, Inc.

4.2.4 Security Boot

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit
Password Description If ONLY the Administrator's password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User's password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20 Setup Administrator Password User Password Secure Boot	Customizable Secure Boot settings
	+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

System Mode Secure Boot Vendor Keys	Setup Not Active Active	Enter Audit Mode. If a current System Mode is User - PK variable will be erased on transition to Audit
Attempt Secure Boot Enter Audit Mode	[Enabled]
Secure Boot Mode Key Management	[Standard]
		+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

4.2.4.1 Security Boot

System Mode Secure Boot Vendor Keys	Audit Not Active Active	Secure Boot activated when Platform Key(PK) is enrolled, System mode is User/Deployed, and CSM function is disabled
Attempt Secure Boot	[Enabled]
Secure Boot Mode Key Management	[Standard]
		+: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

■ Attempt Secure Boot
Secure Boot activated when platform key(PK) is enrolled, system mode is user/deployed, and CSM function is disabled.
- Secure Boot Mode

Secure Boot mode - Custom & Standard, Set UEFI Secure Boot Mode to STANDARD mode or CUSTOM mode, this change is effect after save. And after eset, the mode will return to STANDARD mode.

4.2.5 Boot

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Setup Prompt Timeout Bootup NumLock State Quiet Boot Boot Option Priorities Boot Option #1 Boot Option #2 1 [On] [Disabled] [UEFI: JetFlashTrans...] [UEFI: Built-in EFI ...] Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. ++ +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

■ Bootup NumLock State

Select the keyboard NumLock state.

Quiet Boot

Enables or disables Quiet Boot option.

4.2.6 Save & Exit

Main Advanced Chipset Security Boot Save & Exit
Save OptionsSave Changes and ExitDiscard Changes and ExitSave Changes and ResetDiscard Changes and ResetSave ChangesDiscard ChangesDefault OptionsRestore DefaultsSave as User DefaultsRestore User DefaultsBoot OverrideUEFI: Built-in EFI ShellUEFI: JetFlashTranscend 32GB 1100, Partition 1Launch EFI Shell from filesystem device	Exit system setup after saving the changes.++: Select Screen↑↓: Select ItemEnter: Select+/-: Change Opt.F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save & ExitESC: Exit

www.advantech.com

Please verify specifications before quoting. This guide is intended for reference purposes only.

All product specifications are subject to change without notice.

No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher.

All brand and product names are trademarks or registered trademarks of their respective companies.

© Advantech Co., Ltd. 2018