AFR4EC - Accessory Panduit - Free user manual and instructions

USER MANUAL AFR4EC Panduit

Raceway Channel	See Fig.	Electrical Cables			Data Grade Cables
		14	12	10	24 AWG		24 AWG		24 AWG
		THN/THWN/T90			Cat 6		Cat 6A		Cat 6A (SD)
		0.111	0.13	0.164	0.24		0.3		0.24
		Fill			Fill		Fill		Fill
		Max	Max	Max	Spec	Max	Spec	Max	Spec	Max
		UL Temp Rise Test			40%	60%	40%	60%	40%	60%
Outer Channels (with screws installed)	A	21	15	10	3	4	2	3	3	4
Inner Channels	B	24	17	11	3	5	2	3	3	5

A B B A

Three circular diagrams showing different types of screw heads, with no text or symbols present.

Themountinghardwareusedtosecure theracewayshallbeappropriateforthe mountingsurface.

Screwsprovidedwithracewayare intendedforinstallationonaconcrete surface.

NOTES:

• An adhesive strip may serve only as a positioning aid during the installation process. The raceway shall be secured by mechanical fastening means.
• Holes for mounting raceway and associated fittings should be predrilled into infrastructure prior to the installation of the mounting hardware.
  •A5/32"concretedrillbitisneededfortheprovidedconcretescrews.

BASE&COVER

COUPLER

122a34

Pure technical line drawing of a mechanical assembly without any text, numbers, or symbols

Ensurecouplerisfully engagedwithcover

Simple line drawing of a rectangular object with a circular hole above it (no text or symbols)

Technical line drawing of a structural component with a circular element and directional arrow (no text or symbols)

Staggerbase jointandcover couplingjointto strengthen assembly.

RIGHTANGLE

Technical line drawing of a multi-tiered mechanical component with screw holes and mounting holes (no text or symbols)

Diagram of a mechanical or structural assembly with two symmetrical components and directional arrows indicating flow or movement (no text or symbols)

Technical diagram of a layered structure with directional arrows indicating flow or movement (no text or symbols present)

Technical diagram showing a mechanical assembly with labeled components and directional arrows

Pure technical line drawing of a V-shaped component without any text, numbers, or symbols

TRANSITIONTOT70

Technical diagram showing a structural assembly with arrows indicating direction (no text or symbols present)

Technical line drawing of a mechanical assembly with numbered components (no text or symbols)

Technical diagram showing a mechanical assembly with labeled components and directional arrows (no text or symbols present)

Technical line drawing of a vertical structural component with a base and side panel (no text or symbols)

ENDCAP

(1) 1a Ens mur cap

1a
Ensureendcapandcoverarefullyengagedasshown.0.3"ismaximumallowabledistancebasecanextendbeyondcoverwheninstalling cap.

cap. 0.3"

Line drawing of a rectangular metal frame with internal grooves, labeled with number 2 (no text or symbols on the frame itself)

JUNCTIONBOX

1a
Ensureendcapand coupler(s)connectto junctionboxcoveras shown[8places]
Note: JunctionBoxcanbeassembledbetweenworacewaypathswiththeuseoftwocouplerfittings. Endcapinstallationsshownasreference.

②

Technical line drawing of a mechanical assembly with a bracket and mounting base (no text or symbols)

③

Technical line drawing of a metal beam assembly with mounting holes and internal circular components (no text or symbols)

1"(25.4mm) 3/4"(19.05mm) Rectangular Breakout 1/2"(12.7mm) Rectangular Breakout

BREAKOUTSFORCONDUITAPPLICATIONS

DIVIDEDINSERTAPPLICATIONPOWER/DATAAPPLICATIONDATAAPPLICATIONPOWERAPPLICATION

4

5

6

Technical line drawing of a mechanical device with a tray and mounting base (no text or symbols)

Technical line drawing of a mechanical component with a rectangular base and a small rectangular housing (no text or symbols)

WALLTRANSITION

GREENFIELDAPPLICATIONS-NEWCONSTRUCTION

1/2"drywallapplication5/8"drywallapplication
Determine if you will use 1/2" or 5/8" drywall. Orient standoffasshownfordesiredapplication.
Ifinstallingintoexistinginfrastructure,continuetoBrownfieldapplicationinstructions.
Securebasetosoleboardandroute cablesandwiringasdesired.Donot overtightenscrewsasflooringinstallationmayrequireadjustments.
Adjustwalltransitionfittingbaseheight duringflooringinstallation.Afterdrywall andflooringhavebeeninstalled,secure transitionfittingbasetothefloorusing appropriatehardware.
ContinuewithStep4ofBrownfieldapplicationinstructions.

**OnlyusestandofforGreenfield applications**

BROWNFIELDAPPLICATIONS-EXISTINGINFRASTRUCTURE

Cutholeindrywallbetweenstudstothe dimensionsshown.

④ Raceway Base

Technical line drawing of a mechanical component with an arrow indicating direction (no text or symbols)

Raceway Cover ⑥

Technical line drawing of a mechanical component with an arrow indicating direction (no text or symbols)

Simple line drawing of a corner bracket with a diagonal line extending from it, no text or symbols present.

TABLELEG

INSTALLATIONBETWEEN2RACEWAYCHANNELS

Technical line drawing of a structural support frame with vertical and horizontal components (no text or symbols)

①

① MEASURE TABLE HEIGHT Raceway Cover 3-1/4"

Centeroftablelegtransitionfittingwillsitapproximately3-1/4"fromtheedgeoftheracewaycover.
Routecablespriortoinstallingtheracewaycover.
NOTE: Desired hole in table should be offset from table leg center to accommodate proper mountingoftableleg.
Measuretheheight fromthefloortothe undersideofthetable. Channelshouldbe between3-1/2"to4" shorterthanthemeasuredheight.Ifnecessary,cutchannelfrom bottomedgetoaccommodate.

2

0 0 0 ① 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

③

Mounting Bracket TopHoleof Channel Topof Channel

④

#10-32HexNuts #10-32x1"Screws

Securemountingbrackettotopofchannelusingprovidedhardware. Usethetopholeofthechannelforassembly.Donotfullytightenthe mountingbracketatthistime.

5

Technical line drawing of a mechanical device with no visible text or symbols

5A

Technical line drawing of a mechanical bracket with mounting holes and a close-up inset showing a control panel (no text or symbols)

Ensurecouplersconnecttobottomtransition bootsasshown. [4Places]

6

Technical line drawing of a mechanical component with grid lines and a bracket (no text or symbols)

CaptureLedge BottomEdge of Channel Transition Boot Setbottomedgeofchanneloncaptureledgeofinstalled transitionboot.Connectsecondtransitionboottothefirst.

#8-32x3/4" Wood Screws [4Places] Ensurechannelislevel.Securemountingbrackettoundersideoftable usingprovidedhardware.Fullytightenmountingbracketscrewsto securechannelinplace.

#10-32Hex Nuts [2Places] #10-32x3/8" HexScrews [2Places] Cover [2Places]

10 SteppedFlange [2Places] MountingBracket TransitionBoot Latch [4Places] TopTransitionBoot [2Places]

Routecablespriortoinstallingcovers.Coversaretamper-proof andarenotintendedforeasyremoval.
Assembletoptransitionbootstoeachother. Transitionbootlatcheswill mounttothesteppedflangesofthemountingbracket.
Ifaddedstiffnessisdesired,securebottomofchannelusingprovidedhardwareinthelowermostholesofthechannel.

11

Technical line drawing of a simple structural frame with columns and a vertical column, no text or symbols present

INSTALLATIONASSTANDALONEORWITHSINGLESIDERACEWAYCHANNEL

Technical line drawing of a table with columns and a vertical support structure (no text or symbols)

NOTE: For single side raceway application; above floor raceway should be mounted prior to table leg installation. Centeroftablelegwillsitapproximately3-1/4"fromtheedgeoftheracewaycover.Routecablespriorto installingtheracewaycover.

Line drawing of a simple table with a vertical structural column (no text or symbols)

NOTE: Desired hole in table should be offset from table leg center to accommodate proper mounting of table leg.

① MEASURE TABLE HEIGHT ② Measuretheheightfrom thefloortotheunderside ofthetable.Channel shouldbebetween3-1/2" and4"shorterthanmea- suredheight.Ifnecessary, cutchannelfrombottom edgetoaccommodate.

NOTE: Desired hole in table should be offset from table leg center to accommodate proper mounting of table leg.

3A Mounting Bracket Topof Channel TopHoleof Channel

3B Bottomof Channel BottomHole ofChannel [2Places] Mounting Bracket

©PanduitCorp.2019

INSTALLATIONINSTRUCTIONS

PN616B

4

#10-32Hex Nuts #10-32x1"Screws

Securemountingbracketstotopandbottomofchannelusingprovided hardware. Usetheholesclosesttotheendsofthechannelforassembly. Donotfullytightenthemountingbracketatthistime.

Technical diagram showing mechanical assembly with screws and mounting brackets, labeled with number 5

Pre-drillholesininfrastructureifnecessary.Secure bottommountingbrackettofloorwithproperhardware.(Concretescrewsprovided)

6

#8-32x3/4"Wood Screws[4Places]

Ensurechannelislevel.Securetopmounting brackettoundersideoftableusingprovided hardware.

Technical diagram of a mechanical device with labeled components and magnified views

TransitionBootLatch

7A Ensureendcap(s)or coupler(s)connectto bottomtransition bootsasshown [4places]

⑧ Capture Ledge Stepped Flange BottomEdgeof Channel Bottom Transition Boots

Assemblebottomtransitionbootstogether.Transitionboot latches(showninstep7)willmountosteppedflangesofthe mountingbrackets.Placebottomofchannelontopofcap-tureledgeoftransitionboots.
Tightenallmountingbracketscrewstothechannelatthis time.

⑨ Covers [2Places]

Routecablespriortoinstallingcovers.Coversaretamper proofandarenotintendedforeasyremoval.

10 Stepped Flange [2Places] Transition Boot Latch [4Places] Assembletoptransition bootstoeachother.Transitionbootlatcheswill mounttothestepped flangesofthemounting bracket.

11

Line drawing of a simple table with four legs and a vertical cylindrical structure on top (no text or symbols)