KASTHFP2KWA - Heating Kogan - Free user manual and instructions

USER MANUAL KASTHFP2KWA Kogan

Modern vertical digital temperature range meter with red liquid at the base and a digital display on top (no visible text or symbols)

KOGAN SMARTERHOME™ 2000W TOWER HEATER

FIREPLACE EFFECT

KASTHFP2KWA

Safety & Warnings 3

Components 6

Overview 6

Assembly 8

Operation 10

Connect to SmarterHome™ App 13

Google Home Control 17

Amazon Alexa Control 20

Cleaning & Care 23

Specifications 23

SAFETY & WARNINGS

Ensure to read all instructions and warnings in this user guide prior to first use. Retain this user guide for future reference.

WARNING — KEEP BATTERIES OUT OF REACH OF CHILDREN

- Swallowing may lead to serious injury or death in as little as 2 hours, due to chemical burns and potential perforation of the oesophagus.

Silhouette of a person holding a baby in a circle, no text or symbols present

Warning symbol with exclamation mark and plus sign, commonly used in safety or hazard prevention context

• If you suspect your child has swallowed or inserted a button battery, immediately call the 24-hour Poisons Information Centre on 13 11 26 (Australia) or 0800 764 766 (New Zealand) for fast, expert advice.
• Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if the compartment is not secure.
• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.
• Tell others about the risk associated with button batteries and how to keep their children safe.

Other warnings

• This heater is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the heater by a person responsible for their safety.
• Keep out of reach of children. Children should be supervised at all times to ensure that they do not play with the appliance.
• When in use, never leave the heater unattended.
• This heater's battery compartment cover is secured with a screw. It has been designed so that the battery is not easily accessible to young children. Always ensure that the compartment is secure before use.
• Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
• Always use a heater guard around the heater if used in the presence of children, animals, elderly, or persons with reduced/impaired physical, sensory, or metal capabilities in the absence of adequate supervision.

- This heater supports voltages between AC 220–240V with a frequency of 50Hz. Ensure the socket used to power the heater matches this.

- Do not use this heater on unstable or angled surfaces.

- This heater is for indoor household use. Do not use this heater outdoors or for any other purpose.

- Do not cover or block the air inlet, air outlet, and other openings with anything (for example, curtains, tablecloths, newspapers) as this may lead to overheating, damage, and personal injuries.

- Do not insert anything into the air inlet, air outlet, and other openings as this may lead to overheating and a risk of fire.

- Keep combustible materials (for example, furniture, pillows, bedding, papers, clothes, curtains) at least 1 metre away from the air outlet of the heater.

- Dangerously high voltages are present inside this heater. To avoid electric shock, do not open the heater yourself. Contact a professional if the heater must be opened.

- Do not attempt to repair, disassemble, or modify the heater yourself. There are no user serviceable parts inside.

- This heater will be hot during and directly after use due to residual heat. Do not let bare skin touch the hot surface of the heater to avoid burns.

- Do not expose this heater to water, moisture, or any other liquid to avoid a risk of fire and electric shock.

- Do not use aerosols or steam cleaners on or around the heater.

- Do not use this heater in areas with flammable solvents, explosive gases, varnishes, or glues.

- Ensure the power cord is visible at all times to avoid a tripping hazard.

- When plugging in, ensure the power socket is accessible and located adjacent to, but not above the heater.

- Never let the power cord hang over the edge of a table or counter or let it touch any hot surfaces.

- Do not immerse the heater or power cord into any liquid or allow it to be sprayed. Doing so may lead to electric shock, fire, or other injuries.

- Do not place the heater in areas near water or any other liquid (for example, bathrooms, kitchens, near vases).

- Do not use the heater with wet hands or in damp environments.

- Do not place the heater on deep pile carpet or flokati rugs. Use a heatproof board if necessary.

- Do not use this heater to dry clothes or other items.

- Do not place this heater near flames (for example, candles, stoves).

- Do not move the heater while it is switched on.

- Do not use this heater with any third-party devices (for example, a programmer, timer, separate remote control systems, or any other device that can switch the heater on automatically) as this could lead to a fire risk if the heater is covered, positioned incorrectly, or otherwise lead to an electric shock or injury.

WARNING: In order to avoid a hazard due to inadvertently resetting the thermal cutoff, this heater must not be supplied through an external switching device (for example, a timer) or be connected to a circuit that is regularly switched on and off.

• If the heater is damaged, stop use immediately and contact help.Kogan.com for assistance.
• If the power cord is damaged, stop use immediately and contact help.Kogan.com for assistance.
• If the heater has been dropped, stop use immediately and contact help.Kogan.com for assistance.
• Do not forcibly pull on the power cord. When unplugging, pull the power cord out close to the power socket.
• Always turn the heater off and unplug the power cord from the power socket when not in use, when moving the heater from one location to another, and before cleaning.
• Images used in this user guide are for reference only.
• At the end of the heater's serviceable life it should be disposed of carefully and safely in accordance with local authority regulations.

COMPONENTS

• Tower heater body (x1)
• Mounting screws (x3)
• Remote control (x1)

• User guide (x1)

• Base plate halves (x2)
  • CR2025 lithium battery (x1)

• Warranty card (x1)

OVERVIEW

Handle Control panel Air outlet Air inlet (behind) Power switch (behind) Flame effect display Base

Control panel

High heating mode indicator LED display 24 °C h Low heating mode indicator Fan and power indicators Swing and flame effect indicators Temperature/timer Increase button Temperature/timer decrease button Flame effect button Wi-Fi indicator Power button Timer button Oscillation button Heating mode button

Remote control

Power button Heating mode button Oscillation button Temperature/timer increase button Flame effect button Timer button Temperature/timer decrease button

ASSEMBLY

Before using the heater, the base plate must be assembled and fitted onto the heater. It consists of two halves.

1. Remove the heater, base plate halves, and mounting screws from the packaging.

2. Fit the half of the base plate that has the cable channel incorporated onto the bottom of the heater. Clip the power cord into the cable channel as shown below.

Technical line drawing of a satellite dish antenna with visible components and no text or symbols

1. Aligning with the corresponding screw holes on the secured half, fit the other half of the base plate onto the heater and push down as shown below.

Technical diagram of a mechanical assembly with rotating components and directional arrows (no text or labels)

1. Rotate the assembled base plate anti-clockwise to engage the base plate locking tabs with the heater.

Diagram of a mechanical device with rotating arms and directional arrows indicating rotation (no text or labels)

1. Using a screwdriver (not supplied), secure the assembled base plate to the heater with the mounting screws.

Technical line drawing of a mechanical assembly with intersecting gears and rods (no text or symbols)

OPERATION

Placement

Ensure the tower heater is placed in an upright position and that there is at least a 1 metre clearance around the heater of any objects. The power switch should be in the 'O' position.

Standby and powering on

• Unwind the power cord and plug it into a power socket. Ensure that the voltage used is between AC 220–240V. Turn the power socket on.
• Toggle the power switch (located at the back of the heater) to the 'I' position. The heater will then enter standby, emit a beep, and show the current room temperature on the display.
• Press the power button ‘💡’ on the control panel or remote control to power the heater on.

Note:

When the heater is being turned on for the first time (or being turned on after an extended period of non-use), it may emit a smell or fume. This is normal and should disappear when the heater has been on for a short while.

Heating modes and temperature

This heater features a low heating (emitting at 1400W) and high heating mode (emitting at 2000W).

- To change the heating mode, press the heating mode button ‘💡’ on the control panel or remote control. The low and high heating mode indicators will illuminate according the current selected heating mode.

Temperature

The temperature range available on this heater is between 10–35°C.

• To change the selected temperature, press the increase ‘+’ and decrease ‘-’ buttons on the control panel or remote control.
• If the current room temperature is at least 4^ C colder than the selected temperature, the heater will engage the high heating mode. If the current room temperature is at most 2^ C colder than the selected temperature, the heater will engage the low heating mode.
• When the room reaches the selected temperature, the heating will automatically stop. Heating will automatically resume at the low heating mode when the room temperature reaches 2^ C lower than the selected temperature and continue to regulate accordingly.

Timer

The timer allows users to set the heater to turn off automatically after a pre-set number of hours. To set the timer:

1. Press the timer button ‘💡’ on the control panel or remote control.
2. Press the increase '+' and decrease '-' buttons on the control panel or remote control to select the desired number of hours (0–12) you wish the heater to turn off after. This will be reflected on the LED display.
3. After selecting, the desired number of hours will flash on the LED display four times to confirm before the display reverts to showing the current room temperature.

Oscillation

• Press the oscillation button ‘◦’ on the control panel or remote control to activate the oscillation function. This allows the heater to oscillate left and right whilst emitting heat.
• Press the button again to turn off oscillation.

Flame effect

• Press the flame effect button ‘💡’ on the control panel or remote control to activate the flame effect display.
• Press the button again to turn off the flame effect display.

Powering off

1. Press the power button “⏻” on the control panel or remote control to return the heater into standby. Allow approximately 30–60 seconds for the heater to stop blowing air. This will help protect the components.
2. Toggle the power switch back to the 'O' position to turn the heater off. Turn the power socket off.

Note:

If you are planning to turn the heater on again, allow the heater to cool for 30–60 seconds before turning it on. This will protect the components and preserve the service life of the heater.

Remote control battery replacement

The remote control requires one CR2025 3V lithium battery to operate.

1. Place the remote control down with the buttons facing downwards. Using a screwdriver (not supplied), loosen the cover screw. Press on the release tab and pull out the battery compartment. Remove the old battery.
2. Place one new battery into the battery compartment with the positive '+' polarity facing up. If the battery is placed incorrectly, the remote control will not work.

Note:

Do not use a different type of battery when replacing as this may lead to the remote control not working or cause damage.

1. Insert the battery compartment back into the remote control and ensure it is secure. Tighten the cover screw.

RELEASE

CR2025 SN Pull Press

Overheat protection

• This heater is fitted with a safety overheat protection device. If overheating occurs, ensure the heater and power socket are switched off.
• Unplug the heater and let it cool for 30 minutes. If anything is obstructing the grille, ensure the object is removed.
  • After 30 minutes has passed, turn the heater on again.

Fall protection

This heater comes equipped with a safety fall protection switch. It will cut off the power to the heater if the heater is being knocked over or otherwise falling. This assists in protecting against a risk of fire, overheating, or any other accidents.

CONNECT TO SMARTERHOME™ APP

Install App

Download the "Kogan SmarterHome" app from the Play Store (Android) or App Store (iOS).

Register

If you do not have a Kogan SmarterHome™ account, register or sign in with a verification code sent by SMS.

To register:

1. Tap to enter registration page.
2. The system automatically recognises your country/area. You can also select your country code manually. Enter your email address and tap 'Next.'
3. Alternatively, you can select 'Register by mobile number' and enter the verification code sent to you by SMS.
4. Create a profile on the next page to define your location and room.

10:54 Email Mobile Number Register by Email Australia +61 [e-mail] Get Verification Code I Agree Service Agreement and Privacy Policy

10:55 Email Mobile Number Register by Mobile Number Australia [phone] Get Verification Code I Agree Service Agreement and Privacy Policy

Set device in pairing mode

When the device is first turned on, it may automatically enter pairing mode (Wi-Fi indicator will be flashing slowly).

If not automatically in pairing mode, ensure the heater has just been plugged in. Without pressing the power button, flick the power switch into 'I' position. The heater will enter standby and emit a beep. The Wi-Fi indicator should then be flashing slowly.

Using AP Mode to add a device

1. Once registered, tap "+" in the upper right corner of the app's home page to add a new device through the network.
2. Select the product type from the list of options in the app (Heating & Cooling > Heaters), and then select "Other Mode" from the top-right corner when asked to reset the device.

3:54 Home Light Rain 19°C Outdoor Tempel 80.0% Outdoor Humidity 1000.0NPs Outdoor Air Free... All Devices Living Room Master Badrow No devices, please add Add Device Home Score Use

11:57 Cancel Add Manually Auto Scan Lighting Electrical Home Security Heating & Cooling Air Treatment Clearing Appliance... Kitchen Appliance... Other

3:37 Cancel Other Mode Reset the device first. Power on the device and confirm that indicator light rapidly blinks Resetting Devices > Confirm indicator rapidly blinks

1. Select "AP Mode" for the set-up type.
2. Ensure that the device is in pairing mode, with the Wi-Fi indicator flashing slowly, and tap "Confirm light is slowly flashing".
3. Enter your Wi-Fi details. It is important that your SmarterHome™ device and the app are connected to the same Wi-Fi network during setup.

3:37 Select Network Configuration Mode Select a correct ping mode based on the device type or refer to the user manual Smart Mode The mobile phone will broadcast network configuration information... AP Mode The mobile phone connects to the device's WiFi hotspot and transmit...

3:37 Cancel Other Mode Reset the device first. Power on the device and confirm that indicator light slowly blinks Resetting Devices > Confirm indicator slowly blink

Enter Wi-Fi Password 2.4GHz 5GHz ✓ ✗ Only 2.4G Wi-Fi networks are supported > Your Network Name Password Confirm

1. Follow the in-app prompts to continue AP Mode connection, which will pair your mobile phone to the device's Wi-Fi hotspot to ensure a connection.

Note:

If the Wi-Fi hotspot does not appear on your phone in the list of available networks, your device may not be set in AP Pairing Mode correctly. Try repeating the steps outlined above to ensure your device is ready for connection.

1. The device will commence the pairing process and connect to the app. Ensure your Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until connection is complete.
2. After successfully being added, you will have the option to rename the device and assign it to a location. It will now be listed on the app's home page. Tap the device listing to enter its control page.

12:45 Cancel Connect your mobile phone to the device's hotspot 1. Connect the phone to the hotspot shown below. WiFi WiFi-E SmartLift_XXX Go back to the app and continue to add devices. Go to Connect

11:26 Add Device Connecting... Place your router, mobile phone, and device as close as possible 15% Device found Register Device to Smart Cloud Initializing device...

11:26 Add Device Device added successfully Smart Heater Living Room Master Room... Study Room Dining Room Kitchen Spots Room Backyard Done

Notes:

• The device and the app have to use the same Wi-Fi network.
• The device is only compatible with 2.4Ghz networks.

GOOGLE HOME CONTROL

Note:

You will need to have set up a Google Home account prior to linking your Kogan SmarterHome™ device.

Adding "SmarterHome" to the Google Home app

1. From the home page of the Google Home app, select the "+" icon to access the 'Add and manage' page.
2. Select 'Set up device', then under the Works with Google banner, select 'Have something already set up?'
3. Select the search bar and type 'Smarter Home' to locate the Kogan SmarterHome™ service.

10:17 Home Media Routine Settings

10:17 Add and manage Add to home Set up device Invite home member Create speaker group Create new home Manage services Music and audio Videos and photos Offers Offers

10:17 Set up Set up new devices or add existing devices and services to your home New devices Set up new devices in your home Google Home, Chromecast, SmartDisplays, devices labeled 'Made for Google', Blue C by GE smart buttons, and Philips Hua Bluetooth (without Hue Bridge) Works with Google Have something already set up? Link your smart home services like Philips Hua (with Hue Bridge) and TP-Link

1. Tap 'Authorise' to grant Google permission to access the SmarterHome™ app and your devices.

2. From here, you will be prompted to sign into your SmarterHome™ account using either your email or mobile phone number, depending on which method you used to register your account.

10:18 ← smarter home Add new Smarter Home homes home homeless 1 2 3 4 5 6 7 8 9 10 q w e r t y u i o p @ # # * - + = ( ) a s d f g h j k l z x c v b n m 123 ,

10:20 pct buyouts.com Google will be able to: Receive your public profile Control your devices over internet Authorize You can revoke permission at any time.

1. Once connected, the app will display any compatible devices linked to your SmarterHome™ account. From here you can assign them to rooms and set up any routines.
2. Tap on any of the devices to view a list of available commands.

10:21 Add smart home devices Select devices and add to a room Devices connected within the SmarterHome™ app will appear here if compatible ADD TO A ROOM

10:23 + Home ▼ Media Routines Settings Back garden 2 devices Dog Cam (Backyard) Dog Cam (Undercover) Kitchen 1 device Cat Cam (Kitchen) Other cast devices 8 devices

Note:

Please note that Google Home can only control the base/core functions of any compatible SmarterHome™ devices. To make full use of this product's smart functionality, please use the Kogan SmarterHome™ app.

AMAZON ALEXA CONTROL

Note:

You will need to have set up an Alexa account prior to linking your Kogan SmarterHome™ device.

Adding "SmarterHome" to the Alexa app

1. From the home page of the Alexa app, select the “≡” icon in the top-right and select Skills & Games from the sidebar.
2. Select the search bar and type 'Smarter Home' to locate the Kogan SmarterHome™ skill.

10:28 Good Morning SOUTH MELBOURNE [e-mail] Morning 28° Afternoon 30° Evening 22° Call and message from your Alexa devices Add your phone number to get started.

Add Device Lists Reminders & Alarms Contacts Routines Things to Try Skills & Games Activity Help & Feedback Settings

10:29 SEARCH Search smarter home 1 Result Sort: Relevance Smarter Home "Alicas, set bedroom light to cool white." Smart Home

1. Tap 'Enable to Use' to add the Kogan SmarterHome™ skill to Alexa.

2. From here, you will be prompted to sign into your SmarterHome™ account using either your email or mobile phone number, depending on which method you used to register your account.

3. Tap 'Authorise' to grant Alexa permission to access the SmarterHome™ app and your devices.

10:29 SMARTER HOME Smarter Home Kogan.com Rated: Guidance Suggested ENABLE TO USE Account linking required If you have any problem when you use this skill, you can contact us with email: [e-mail] Amazon Alexa and the Kogan smart home products work together to help you control home appliance nice and easy.... See More Start By Saying English (AU) "Alexa, set bedroom light to cool white." "Alexa, dim the bedroom light to 50%." "Alexa, turn on my livingroom heater." About Note Email: Comments Play Custom

10:30 Account Binding https://pry1.tuyaus.com/pl/?client_id=amz1_ Alexa by Amazon will be able to: Receive your public profile Control your devices over internet Authorize You can revoke permission at any time.

1. Once connected, the app will perform a search and display the devices linked to your SmarterHome™ account.

2. When your devices have successfully connected to the Alexa app, you will be able to control your Kogan SmarterHome™ devices via Alexa's voice commands.

Alexa is looking for devices to connect... This may take up to 45 seconds.

10:45 ALL DEVICES Cat Cam (Study) • New Device Alexa on this Phone Online Cat Cam (Kitchen) Fish Cam light 1 Plug 1

Note:

Please note that Alexa can only control the base/core functions of any compatible SmarterHome™ devices. To make full use of this product's smart functionality, please use the Kogan SmarterHome™ app.

CLEANING & CARE

Before cleaning, ensure that the heater is switched off and unplugged from the power socket.

Clean the exterior surface of the heater with a dry, soft cloth.

Notes:

• Do not use any detergents or solvents to clean the heater.
• Do not use sprays on the heater.
• Do not submerge the heater in any liquids.
• Do not attempt to open and try to clean the interior of the heater.

Storage

Neatly wind the power cord around the base of the heater to prevent any damage to the power cord. Store in a cool dry place.

SPECIFICATIONS

Power supply supported

AC 220-240V, 50/60Hz

Wattage 2000W

Disposal

This marking indicates that this heater should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Need more information?

We hope that this user guide has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com