AS01346FP3 - Television Allsee - Free user manual and instructions

USER MANUAL AS01346FP3 Allsee

Diagram showing nine numbered musical notation or instrument placement steps arranged in a grid, with vertical bars and horizontal lines indicating movement.

Note: The displays are installed by the numerical order given.

graph TD
    A["Step 1"] --> B["Step 2"]
    B --> C["Step 3"]
    C --> D["Step 4"]
    D --> E["Step 5"]
    E --> F["Step 6"]
    F --> G["Step 7"]
    G --> H["Step 8"]
    H --> I["Step 9"]

Note: The angle of displays are adjusted by the numerical order given.

Maintenance

- Check that the bracket is secure and safe to use at regular intervals (at least every three months)

- Please contact your distributor if you have any questions.

INSTALLATION MANUAL

Video Wall Stand and Accessories

Technical line drawing of a vertical structural component with multiple horizontal supports (no text or symbols)

Optional Accessories

AS01K Note: The accessories are not standard equipped. The accessories will be selected according to user requirement.

CAUTION: DO NOT EXCEED RATED LISTED WEIGHT, SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

AS01346FP

300x300/400x200 400x400 /600x400

ISSUED: OCT. 2014

NOTE: Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

AS01346FP

rubber pad (x4)

iron expansion bolt (x6)

Package M (x3)

AS01K (The following accessories are optional)

power socket (x1) T-H

ST4.8x9.5 (x4) P-G

1. Installing the Rubber Pads
   

• Lift the steel base by grasping the cable ties. • Peel off the backing paper from the rubber pads and stick the rubber pads on to the steel base.

1. For the model AS01K installation

(Assembly based on the accessories selected by user.)

P-G T-H

Attach the power socket to the back of column using the appropriate screws. Tighten all screws with a phillips screwdriver.

3a. For Concrete Floor Mounting

Technical diagram showing a mechanical component before and after modification, with dimensional annotations and a magnified detail view.

Mark the exact location of mounting holes and pre-drill these mounting holes with a 12mm drilling bit to at least 62mm in depth. Remove the dust in the holes.

Diagram showing a mechanical component with labeled parts and an arrow indicating transformation or assembly.

First tighten the iron expansion bolts with an Allen key, and then loosen the iron expansion bolts in order to separate the bolts and the expansion tubes.

P M E Attach the connecting plate to the bottom of the column using the appropriate screws. Tighten all screws with an Allen key. Insert an expansion tube into each of these holes. Using the bolts mount the column to the floor. Tighten all screws with an Allen key.

3b. For the Floor Stand Mounting

Remove the cable ties.

Attach the column to the steel base using the appropriate screws. Tighten all screws with an Allen key.

1. Installing the Universal Plates
   

Technical illustration of a metal frame structure with an inset showing a close-up of a structural detail (no text or symbols present)

Insert the universal plates to the column along the column rails respectively. NOTE: With the arrow pointing upward.

Tighten all screws to secure them with an Allen key. X+5mm (X=Height of display) X+5mm (X=Height of display)

1. Installing the Top Cover
   

Attach the top cover to the column using the appropriate screws. Tighten all screws with an Allen key.

5

1. Installing the Adapter Brackets
   

Top of the display

6-1 For Flat Back Screens

Technical diagram showing electrical switch assembly with labeled components and a magnified view of the circuit board.

6

6-2 For Recessed Back Screens or to Access A/V Inputs

Technical diagram showing mechanical assembly with labeled components and corresponding circular diagrams illustrating assembly steps.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.
- Position the adapter brackets as close as possible to the center of the displays.
- Screw the adapter brackets onto the displays.
Tighten all screws but do not over tighten.

1. Hanging the Displays onto the Universal Plates
   

Note: The displays are installed to the universal plates from the bottom up. • Lift the display carefully and pull downward two straps at the same time, then hook the adapter brackets to the universal plate. Fasten the adapter brackets to the universal plate by releasing the straps. • The other displays are hung onto the universal plates in the same way

Technical diagram showing mechanical assembly steps with magnified views of components

Use the padlocks to prevent the displays from being stolen (The padlocks are not included).

1. Micro-Adjustment
   

If the displays uplifted, rotate the adjustment screws as shown in figure. Note: Adjust the angle of displays by the numerical order given.

Technical diagram illustrating mechanical assembly with labeled components and directional arrows indicating motion or assembly steps.

If the displays tilted down, rotate the adjustment screws as shown in figure.

up down P 1mm Note: Leave a one millimeter gap between the displays.

Rotate the adjustment screws as shown in figure to make a one millimeter gap left between the displays.

1. Cable Management
   

Mechanical assembly diagram showing two views of a mechanical component with a magnified inset (no text or symbols)

Insert the cable clamps horizontally into the plate slots, then turn the cable clamps to the vertical to secure them.

Technical line drawing of a multi-tiered mechanical assembly with vertical supports and mounting brackets (no text or symbols)

Run the cables through the cable clamps and the rubber strip.

10. Adjustment

+3° -3°

11. Multi-screen Combination Solution

graph TD
    A["Loosen the screws in the plastic covers in order to remove the plastic covers."] --> B["Remove the screws attaching the front of the universal plates."]
    B --> C["Connecting attachment"]
    C --> D["Leosen the screws in the connecting fittings in order to slide the connecting attachments to both sides of the connecting fittings. Then tighten all screws to secure."]

X+5mm (X=Height of display) Insert the connecting fittings to the appropriate position along the universal plates rails. X+5mm (X=Height of display) B

Note: Make sure that the universal plates are at the same level with each other. X+5mm (X=Height of display) X+5mm (X=Height of display) Use the connecting fittings to assemble the other stand. Note: Make sure that the stands are in alignment. Note: The position which the connecting fittings insert to the universal plate is determined by the size of displays. Smaller display Larger display or O

Tighten all screws to secure them.

Diagram showing six labeled mechanical or structural assembly steps, numbered 1 to 6, with vertical and horizontal components.

Note: The displays are installed by the numerical order given.

1mm Note: Leave a one millimeter gap between the displays. ① ② ③ ④ ⑤ ⑥ 1mm

Note: The angle of displays are adjusted by the numerical order given.