AS0364T - Television Allsee - Free user manual and instructions

USER MANUAL AS0364T Allsee

1. Lock the Pop-out Module with the Plastic Locking Pieces
   

Technical diagram showing mechanical assembly with magnified detail and directional arrow, likely illustrating a process or assembly.

Maintenance
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
- Please contact your distributor if you have any questions.

INSTALLATION MANUAL

Video Wall Mount

Technical line drawing of a mechanical lifting frame structure (no text or symbols)

CAUT ION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

AS0364T

200x200 /300x300 400x200/400x400 600x400

ISSUED: DEC. 2014

NOTE: Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

wall plate (x1) pop-out module A

Technical line drawing of a mechanical frame or bracket assembly (no text or symbols)

B

adapter bracket (x2) C

VESA adapter (x2) D

VESA adapter (x2) E

M8 nut (x8) F

M8×12 (×8) G

antiskid block (x2) H

plastic locking piece (x2)

Package M

M5x14 (x4) M6x14 M-A

(M-B) (x4)

M8x20 (x4) M-C

M6x30 (x4) M-D

M8x30 (x4) small spacer (x8/washer (x4) M-E M-F

M-G

big spacer (x4) M-H

Package W

ST6.3x55 (x6) W-A

concrete anchor (x6) W-B

D6 washer (x6) W-C

1. For Solid Brick and Concrete Wall Mounting
   

60mm (2.4") ø 10mm (ø 3/8") Mark the exact location of mounting holes Drill pilot holes W-B W-C W-A Screw the wall plate onto the wall

WARNING

Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1. For Video Wall Installation (Mounting space as shown below)
   X=Length of display Y=Height of display
   

X X Y+5mm Y+5mm

1. Installing the Pop-out Module
   

Technical diagram of a mechanical device with an inset close-up showing a component (no text or symbols visible)

Please take off the caps before installation.

Hang the pop-out module onto the wall plate. Secure it by tightening both screws.

1. Installing the Adapter Brackets

For the VESA:400x400 600x400 Attach the VESA adapters to the adapter brackets using the appropriate screws and nuts so that the hole pattern can be expanded to the VESA 400x400 and 600x400.

Top of the display

4-1 For Flat Back Screens

Technical diagram showing assembly of TV components with labeled parts M-A, M-B, M-C and a magnified view of the internal structure.

4-2. For Bump-out or Recessed Back Screens

M-C M-F M-G M-C M-D/M-E M-F M-G M-C M-D/M-E M-F M-H M-D/M-E M-F M-G M-H

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen. - Position the adapter brackets as close as possible to the center of the display.
- Screw the adapter brackets onto the display
Tighten all screws but do not over tighten.

1. Hooking the Display onto the Pop-out Module
   

Diagram illustrating mechanical assembly steps with labeled diagrams showing progressive assembly from left to right.

Note: Before hooking the display, make sure the knobs are rotated to the unlock position.
- Lift the display carefully and hook the display onto the pop-out module. Rotate the knobs to the lock position to secure the display.
- Use the padlock to prevent the display from being stolen.(Padlock is not included)

1. Adjustment
   

Push the display to left or right to enable fast alignment.

Handles for tilt adjustment. Screws for micro-adjustment of up and down. Knobs for micro-adjustment of in and out.

Left

Right

Pure mechanical assembly diagram without any text, numbers, or symbols

Left

Right

Push the display inward and then release it, the display will be pop-out. Kickstands provide tilt access for easy cables management and maintenance.

1. Level the Displays
   

Technical line drawing of a wall-mounted device with four panel layouts and a separate close-up view (no text or symbols)

Adjust the display to keep level in vertical and horizontal directions.

1.2mm Note: Use the plastic locking piece to measure and keep a 1.2 mm gap between displays. ③ ④ ① ② Note: Install-adjust the displays by the numerical order given. 1.2mm

1. Fixing the Brackets Position with the Antiskid Blocks
   

Technical diagram showing mechanical assembly with labeled components and a magnified view of the internal structure.

Install the both antiskid blocks as close to the adapter brackets as possible. Tighten screws on the antiskid blocks using a proper screwdriver to prevent display from moving.