DIRBB2007S21W - Unspecified Panduit - Free user manual and instructions

USER MANUAL DIRBB2007S21W Panduit

Rear of C (Hot A) 7004 Inlet Duct

Front of Cabinet (Cold Aisle)
Component Guide
Note: Bracket Has (2) Notches on the Top

Pure technical line drawing of a rectangular frame with no text or symbols

(1) Left Hand Bracket

Isometric line drawing of a rectangular frame with internal components and dimension lines (no text or symbols)

(1) Inlet Duct Box

Technical line drawing of a mechanical component with two views (no text or symbols)

(1) Right Hand Bracket

Pure 3D line drawing of a rectangular frame with no text, numbers, or symbols

(1) Side Duct

Simple line drawing of a rectangular frame with four rounded corners and a vertical side (no text or symbols)

(2) Adjustable Brackets

(1) Side Duct Mounting Bracket A

(1) Side Duct Mounting Bracket C For (FSNA110-820 series server)

(1) Side Duct Mounting Bracket B

STEP 1

Device Placement (Legacy Cabinets Only)

• Due to physical constraints posed by the front-to-back beams on the Net-Access Legacy cabinet, there are certain areas of the cabinet that the device can not be mounted in when used in conjunction with this inlet duct.
• For Net-Access Legacy cabinets, front equipment rails need to be in full forward position and the rear equipment rails need to be 24.25" - 26.12" back.

NOTES: Numbers-up RU numbering (#1 at bottom) assumed.

45 RU Net-Access CN*** Cabinet (Legacy) Device Keep-Out Area RUs 42-45 Device Can Be Installed in RUs 24-41 Device Keep-Out Area RUs 20-23 Device Can Be Installed in RUs 3-19 Device Keep-Out Area RUs 1-2 42 RU Net-Access CN*** Cabinet (Legacy) Device Keep-Out Area RUs 39-42 Device Can Be Installed in RUs 24-38 Device Keep-Out Area RUs 20-23 Device Can Be Installed in RUs 3-19 Device Keep-Out Area RUs 1-2

For Technical Support: www.panduit.com/resources/install_maintain.asp

STEP 2

Device Placement (N-Type Cabinets Only)

• For Net-Access (N***) Cabinets, there are no device keep out areas. The only restriction on the switch placement is that 2 RU must be left open above the switch.
• For Net-Access (N*** ) cabinets, front equipment rails need to be in full forward position and the rear equipment rails need to be 24.25" - 26.12" back.

NOTES:

Numbers-up RU numbering (#1 at bottom) assumed.

Device Keep-Out Area RUs 44-45 45 RU Net-Access N*** Cabinet Device Keep-Out Area RUs 41-42 42 RU Net-Access N*** Cabinet Device Can Be Installed in RUs 1-43 Device Can Be Installed in RUs 1-40

For Technical Support: www.panduit.com/resources/install_maintain.asp

STEP 3

Left / Right Hand Bracket Installation

• Using (2) #10-32 nuts, attach (1) adjustment bracket to the left hand bracket. Set adjustment bracket to fit equipment rail spacing.
• Using (2) #10-32 nuts, attach (1) adjustment bracket to the right hand bracket. Set adjustment bracket to fit equipment rail spacing.
• Attach the left hand and right hand brackets to the cabinet with (8) #12-24 screws and (8) #12 star washers.

Equipment Rail Spacing Adjustment Bracket (2) #10-32 Nuts Left Hand Bracket

Rear of Cabinet (Hot Aisle) Left Hand Bracket (8) # 12 Star Washers (8) #12-24 Screws Right Hand Bracket Front of Cabinet (Cold Aisle)

Right Hand Bracket Adjustment Bracket (2) #10-32 Nuts Equipment Rail Spacing

STEP 4 Attaching Flap Seal to Side Duct

- Attach (1) strip of flap seal to

Side Duct Flap Seal

STEP 5

Attaching Side Duct Bracket A to Side Duct

• Using (2) #10-32 nuts, loosely attach side duct bracket (A) to the side duct.

Side Duct Side Duct Bracket A (2) #10-32 Nuts

STEP 6

Attaching Side Duct to Right Hand Bracket (Day 1 Installation)

• Slide the (2) threaded studs on the side duct into the (2) slots in the right hand bracket.
• Secure the side duct to the right hand bracket with (2) #10-32 nuts.

Rear of Cabinet (Hot Aisle) (2) #10-32 Nuts Side Duct Right Hand Bracket Front of Cabinet (Cold Aisle)

STEP 7

Attaching Side Duct to Right Hand Bracket (Day 2 Installation)

• From the Rear of the cabinet, slide the side duct into place with the (2) threaded studs on the side duct into the (2) slots in the right hand side bracket.
• Secure side duct to right hand bracket with (2) #10-32 nuts.

Front of Cabinet (Cold Aisle) Right Hand Bracket Side Duct Rear of Cabinet (2) #10-32 Nuts

For Technical Support: www.panduit.com/resources/install_maintain.asp

STEP 8

Attaching Side Duct Bracket B

• Slide the tab on side duct bracket B into the slot on side duct bracket A.
• Secure side duct bracket B to the cabinet with (2) #12-24 screws and (2) #12 star washers.
• Tighten the (2) #10-32 nuts on side duct bracket A that were previously left loose.

Front of Cabinet (Cold Aisle) Side Duct Bracket B Rear of Cabinet (Hot Aisle) Front of Cabinet (Cold Aisle) Side Duct Bracket A (2) #12-24 Screws (2) # 12 Star Washers Side Duct Bracket B Rear of Cabinet (Hot Aisle)

For Technical Support: www.panduit.com/resources/install_maintain.asp

OPTIONAL STEP 8

Attaching Side Duct Bracket C For (FSNA110-820 SERIES CABINET)

• Slide the tab on side duct bracket C into the slot on side duct bracket A.
• Secure side duct bracket C to the cabinet with (2) #12-24 screws and (2) #12 star washers.
• Tighten the (2) #10-32 nuts on side duct bracket A that were previously left loose.

Front of Cabinet (Cold Aisle) Side Duct Bracket C Rear of Cabinet (Hot Aisle) Front of Cabinet (Cold Aisle) Hole Identifies Bracket C Side Duct Bracket A

(Cold Aisle) (2) #12-24 Screws (2) # 12 Star Washers Optional Side Duct Bracket Rear of Cabinet (Hot Aisle)

For Technical Support: www.panduit.com/resources/install_maintain.asp

STEP 9

Installing Inlet Duct Box

- Install the inlet duct box by sliding the box into the left hand and right hand brackets, along built in guide flanges and securing with (2) #10-32 nuts.

Rear of Cabinet (Hot Aisle) Inlet (2) #10-32 Nuts Front of Cabinet (Cold Aisle)

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

www.panduit.com

E-mail: