KPC-HNV522M - Security Camera KT&C - Free user manual and instructions

USER MANUAL KPC-HNV522M KT&C

White surveillance camera with lens and control panel (no visible text or symbols)

Thank you for choosing our high quality camera.

Before attempting to connect operate this unit, please read and follow these instructions.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Use Class 2 Power Supply Only

CONTENTS

1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTION
3. FEATURES
4. EQUIPMENT AND ACCESSORIES
5. CAMERA COMPONENT DESCRIPTIONS
6. INSTALLATION
7. DIMENSIONS
8. SPECIFICATION
9. OSD MANUAL

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions;

1. This device may not cause harmful interference

2. This device must accept any interference received, including interference

that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This equipment operates, used and can variate radio (conversion agent).

environment. The equipment, generation, use, and can Romania radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

Interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

Interference at his own expense.

WARNING

This is a class A product. In a domestic environment this product may cause radio interference

in which case the user may be required to take adequate measures.

Caution

Any changes or modifications in construction of this devices which are not expressly approved

by the party responsible for compliance could void the user's authority to operate the

equipment.

CAUTION

1. A regulated DC12V 500mA power supply is recommended for use with this camera

(for the brand, products and the realized products expected.)

An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out of subject.

1. It is therefore that the contents of them will be found that has a lack of quality and could improve level. If your monitor is switched to high importance then please adjust accordingly

2. Do not attempt to disassemble the camera to gain access to the internal components.

Refer servicing to your charger

1. Never face the camera towards the sun or any bright or reflective light, which may cause smear

on the picture and possible damage in the Image Sensor.

1. Do not remove the serial subscriber for the warranty service

2. The apparatus must be connected to a main socket outlet with a prospective mounting connection.

1. CAUTIONS

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) The marking shown on the product or its literature, indicate that it should not be disposed and/or households waste at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material process. The product should not be mixed with other commercial waste purchased this product, or their face government office, for details of where and now they can take item for environmentally safe recycling. Business uses should contact their supplier and check the terms and conditions of the contract. Household users should contact either the retailer where they for disposal.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions

2) Keep these instructions

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apperative near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

6) Do not install near any heat sources such as radiators, heat registers,

sloves, or other apparatus (including amplifiers) that produce heat.

9) Do not defect the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fill into your outlet, consult an electrician to replacement all the obsolete outlet.

10i Protect the power cord from being walked on or pinched particularly at plugs.

convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apperatus combination to avoid injury from up-over.

13) Unplug this apparatus during lightning storms or when unused for long

34) Refrall contains to qualified center personnel. Containing is required when

the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus. The apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

3. FEATURES

• High Resolution SONY 1 / 3" 2.1 M Progressive Color CMOS Image Sensor, 1920x1080 30fps
• Support various digital video output
720p80, 720p50, 1000p30, 1000p25
• Video Outputs
Primary HD-SDI (BNC) Test / Setup TV Out (Test Point-adapter to BNC included), NTSC / PAL selectable
- OSD menu for setup and config
- Provides True Day / Night Capability with Motorized IR Cut Filter
• 20 Long Life IR Illuminations for 0 Lux viewing performance and
range to 10m (32 feet)
- Lens: Board Le
• Power Source: DC 12V
• 3-Axis Gimbal
• IP65 Weather Resistant

4. EQUIPMENT AND ACCESSORIES

Camera Manual Template Screws, Set Screw / L-Wrench / Plastic Anchors Plastic Anchors Screws L-Wrench Set Screw Option - Remote Control (OSD Key) Max. 25M

5. CAMERA COMPONENT DESCRIPTIONS

Housing Ball IR LED Photo Cell Housing Ball Bracket Housing Top Housing Bottom

1. INSTALLATION
   

Tempoize 70° 140° 70° Plastic Anchors (4mm) Tapering Screws-4x25L (/mm) Open Close Set Screws-M2.0x3L (1mm) L-Wrench 10

6. INSTALLATION

• MONITOR CONNECTION

graph TD
    A["Power Source"] --> B["BRC Future (HD SD link)"]
    B --> C["DC 1N N (SD link)"]
    C --> D["HD SD 1N"]
    D --> E["12V Power Supply"]
    E --> F["Control Unit"]
    F --> G["Monitor"]

* Remote Control - Circuit Diagram (Option)

Function

SWI: Menu OSD Menu on / off. Selection.

SW2: Up CBD Menu up.

SW3: Down QSO Men: D

SMA: Dell OSO Merc Ltd

SWS: Right OED Menu Right

When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.

1. DIMENSIONS
   

U-Binom C12 24R133 65 A404.5 D98.5 12 B10 IT harmonic side

1. SPECIFICATION

Image Series 2, Mapa Plot	3pt Exner SONY CMOS
Effective Files 1864 (H) x	105 (V) 30fps
Unit Cell Screen 2.8 (H) x	2.9 (V)
Video Output Mode	HD-SD: 2Gp66, 7Gp50, 168p30, 108p25
Minimum Illumination & Light	TV Out NTSC / PAL Selectable
Video Output # HD-SDI 1.0 x	Vo-p Composite (/50)
IR LED 800mm , 20ca
IR Uram Range Up to 10M x	132 Feet )
5th Data More than 5dB
Shutter Space Auto / Max. s selectable
Manual Shutter Speed	1/30(25), 1/50(50), 1/120(100), 1/240, 1/300, 1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/38K, 1/68K
D-WDR / BLC OFF / BLC	D-WDR
AGC Max: 29 dB
Stand OFF/LOW / Mildor F / HiR
Day & Night True Day & Night with ICR Mechanism
White Balance AUTO / AU	Out / PUSH MANUAL
Digital Zoom Scale T's - 26
Proxy Missing Zone 24, On / Off
Lors Board Lens
OSO	Built-in
Power Consumption	DC 12V±10%; Max. 420mA
Weight	Approx. 300g
Dimensions	003 X 65
Coil-family	CF, FCC, KC
Temperature / Humidity	Operation: 14°F - 122°F - 16°C - 150°C - 20 - 86%
(m condensing)	Storage: -4°F - 140°C - 20°C - 80°C - 20 - 90%

*Specifications and designs are subject to change for improving the functionality of this product without notice.

1. OSD MANUAL
2. Menu structure

Main Sub	Menu Sub	Kieju
EXPOSURE	SHORTS	MANUAL AUTO	ITEM	USB250, HDMI 1, 12'28'19C, 12'40, 16'39, 19K, 12K, 14K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 18K, 1
	DSS OFF X2 X3	X4, X5, X6, X7, X8
	RIO S=15
	BASE SPEC-SO# Z/UKHZ
	RESET DATA-LOCK/DEF.
	RETURN BACK EXT.
WHITE BALANCE	WHODE	AUTO AUTOCHI PUBH SIMUL	CO-GIT LEM*	CW / MIDDLE / HIGH
			B-6AM-0 - 20
			SC-MAIN - 20
	SALUM CONDITION - 20		RETURN BACK EXT.
	RESET DATA-LOCK/DEF.
	RETURN BACK EXT.
D-WOR / BLO	NODE OFF BIG D-WOR
	BIG OSD OFF - 0V
	BIG POS-X Y - 0
	BIG SIZE - C - 20
	BIG SIZE Y - C - 20
	LEFT DATA-LOCK/DEF.
	RETURN BACK EXT.
DNR			DFT, LOW MIDDLE, HIGH

1. OSD MANUAL

Main Menu Menu Menu
IMAGE	SHAIFEN 35.0 - 2X
	BOXS 5 - 1
	FLIP OFF, HUPF / V FUP/ W FLP
	LHS BLNURG ON 7:20
	BOXOM 4 X/2X / 2X 6X 8X 10X 12X 14X 16X 18X 20X
	RESET DATA BACK DEF
	RE TURN BACK EXT
SPECIAL	PRVACY OFF/ON	DONE NO 0 - 20
		ONE OF OPEN
		POS 0 - 20
		YQSO 0 - 40
		RUS 0 - 40
		Y325 - 20
		COLOR	BLK WH, YEL CYN GRN JAL, WID BLU
		THASE 0 - 4
		RESET DATA BACK DEF.
		RETURN BACK EXT.
	A NAME OFF/ON	LEVEL 0 - 20
		COLOR	BLK WH, YEL CYN GRN JAL, WID BLU
		RESET DATA BACK DEF.
		RETURN BACK EXT.
	PATTERN OFF (A)
	RESET DATA BACK DEF
	RE TURN BACK EXT
SYSTEM	ED FORMAT 38W / 720P
	BD IT'S	SHORT ZING
	CBS FORMAT	TEST PAL	CIVES VIEW CROP/FULL
	APPLY	OK ON	RETURN BACK EXT.
	SYSTEM CARD		SW VERSION
			SET VERSION
			RETURN BACK EXT.
	RESET
	RETURN BACK EXT

9. OSD MANUAL

• Function Description

- EXPOSURE : Go sub menu for camera exposure control.

- WHITE ALANCE : Go sub menu for camera white balance control.

- D-WDR / BLO : Go sub menu for camera D-WDR or BLO action.

- DNR : Control noise reduction setting.

- IMAGE: Go sub menu for adjust image functions.

- SPECIAL : Go sub menu for special feature control.

- SYSTEM: Go sub menu for system control & information.

- Reset Data All : Reset camera's all feature data to default value.

1. EXPOSURE

- BRIGHTNESS : Adjust image brightness value.

- SHUTTER: Select shutter speed control type

• LEVEL: Adjust shutter speed at manual shutter mode

- DSS: Adjust digital slow shutter control level.

- AGC : Adjust max gain level for brightness control

- BASE FREQ : Select basic control frequency for control camera feature.

2. WHITE BALANCE

- WB MODE : Select white balance control mode.

AUTO : Full auto control mode in color temperature range 2300K-10000K.

AUTOext : Extended auto mode for special

PUSH : Enable for the control setting for specific environment

Push & release, for fix WB control setting.

MANUAL : Enable WB control setting by user's intention

• COLOR TEMP.: Select color temperature range for WB control at manual mode.

• R-GAIN : Adjust red color gain for WB control at meual mode.

• B-GAIN : Adjust blue color gain for WB control at manual mode.

- SATURATION : Adjust color saturation level.

9. OSD MANUAL

1. D-WDR / BLC

- MODE : Select D-WDR / ELC mode.

BLC : Act in Backlight compensation mode.

D-WDR : Digital wide dynamic range control.

- BLC OSB : Display BLC control zone in screen. - BLC POS-X : Select BLC control zone vertical position

- BLC POS-Y : Select BLC control zone horizontal position.

- BLC SIZ-X : Select BLC control zone vertical size.

- BLC SIZ-Y : Select BLC control zone horizontal size

1. DNR: Reduce image's noise

2. IMAGE

- SHARPNESS: Adjust image sharpness level.

- GAMMA : Gamma Curve Select

- FLIP : Vertical & Horizontal flip setting.

- LENS SHADING : Enable lens shading compensation.

- DZOOM : Select digital zoom magnification.

1. SPECIAL

- PRIVACY: Setting for protect private area in image using mask setting

+ ZONE NO.: Select private mask zone number

• ZONE OP.: Select zone mask display on/off.

+ X-POS : Select zone horizontal position

• Y-POG : Select zone vertical position.

• X-SIZ : Select zone horizontal size. • X-SIZ : Select zone vertical size.

- 1-32. Uthurn Zone vehicle size:

* COLOR : Select mask color + TRANS : Select mask trans

- TRANS. Select mask transparency level - HLMCK: Mask image high light area

- HLMASK : Mask Image: high light area.

* LEVEL: Select high light level. + OBLOR: Select mask series

- COLOR: Select mask 3D - PATTERN: Color bar display Select

9. OSD MANUAL

1. SYSTEM

- SDI FORMAT: 1000P / 720P

- SDI FPS : 30 or 25 fps in 1080p mode

60 or 50 fps in 720p mode.

CVBS FORMAT: NTSC

• CVBS VIEW : CVBS out video angle setting.

- CROP : Cut the scene outside area for keep image aspect ratio.

< FOLL : Fill the full angle scene into image with

H-V size & ratio change

- APPLY : Apply all video setting changed at once.

Use the Set BUSH to apply.

- SYSTEM INFO.

• SW VERSION : Camera's basic software version.

+ SET VERSION : Camera's feature control setting version.