CE-H26F11-S1 - Computer accessory Siig - Free user manual and instructions

USER MANUAL CE-H26F11-S1 Siig

Red circular logo with a white stylized 'S' line (no text or symbols)

SIIG®

3x3 4K Video Wall Processor with

USB-C / DP / VGA / HDMI

User Manual

SIIG® 3x3 4K Video Wall Processor Input Type C UGA DP USB Source Up Stream None Enter IR

04-1297A

P/N CE-H26F11-S1

Dear Customer

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

Directory

1. FEATURES....3
2. NOTICE....3
3. SPECIFICATIONS .... 4
4. PACKING CONTENTS .... 4
5. PANEL DESCRIPTIONS....5
6. CONNECTING AND OPERATING....6
7. CONTROL INSTRUCTION 8
   7.1 Remote Control....8
   7.2 Video switching operation....9

7.2.1 Video Switching....9
7.2.2 Video Wall Setting....10
7.2.3 Mirror....11
7.2.4 Rotate 12
7.2.5 Edge 13
7.2.6 Format....14
7.2.7 EDID 14

7.3. Audio Setting ...... 15

7.3.1 Audio input setting....15
7.3.2 Audio output setting....16

7.4. System Setting ...... 16

7.4.1 Baud rate 16
7.4.2 TCP/IP setting 17
7.4.3 Reboot....19
7.4.4 Factory reset....19
7.4.5 System information....19

7.5. Web Control 20

7.5.1 Interface introduction....22
7.5.2 Video wall setting....23
7.5.3 Mirror....25
7.5.4 Rotate 25
7.5.5 Edge 26
7.5.6 Format 26

7.5.7 EDID 27
7.5.8 Audio output setting....27
7.5.9 Audio input setting....28
7.5.10 Network interface....28
7.5.11 Reset 29
7.5.12 Password 29

1. RS232 CONTROL....30

9 FIRMWARE UPDATE .... 30

9.1 MCU update....30
9.2 GUI Update....31

MAINTENANCE 31

PRODUCT SERVICE....31

1. FEATURES

● Support USB TYPE-C / VGA / DP / HDMI input.
● Support 4K 3x3 video wall, cascading to create 3x4,4x5,5X6, and max 10x10 video wall.
● Support output image 180° rotation.
● Support highest resolution up to 4K30HZ 4:4:4 for all inputs.
● Support EDID management: Two default EDID: 4K30HZ, 1080P.
● Support HDCP2.2/1.4.

● Support panel button; IR remote; RS232 command and Web GUI to control.

● Support SPDIF and Analog audio extraction

● Support third-party platform control via RS232 port or Lan.

● 1U rack design, easy installment.

● DC 24V 2A power supply.

● Unit size: L438x W274x H44 mm.

2. NOTICE

Our company reserve the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice.

1. SPECIFICATIONS

Operating Temperature Range	0 to +40°C (32 to +104°F)
Operating Humidity Range 5 to 90 % RH	(no condensation)
Input Video Signal 0.5-1.0 volts p-p
Input DDC Signal 5 volts p-p (TTL)
Video Format Supported Ultra HD TV/FHDTV: 4K@30Hz/1080P
Audio Format Supported LPCM 16bit 24bit 44.1KHz,48KHz
Input ports	1xUSB TYPE-C, 1x DP, 1xVGA, 1xHDMI
Output ports 9xHDMI,1xHDMI Loop out
Splitter mode	1x9 HDMI Splitter
Video wall mode	1x1;1x3;1x4; 2x2; 2x3; 2x4; 3x1; 3x2; 3x3; 4x1; 4x2; 4x3-1; 4x3-2; 3x4-1; 3x4-2; 4x4-1; 4x4-2
Cascade video wall mode	4x3; 4x4; etc. Max10x10
Control Way	Panel control, Web control, Remote control, RS232 control
Power consumption	33watts (Maximum)
Dimension (mm)	L438x W274x H44 mm

4. PACKING CONTENTS

1) 3x3 4K Video Wall Processor with USB-C / DP / VGA / HDMI
2) 1x Power supply 24V2A
3) 1x User manual
4) 6x Screws, 2x detachable mounting ears
5) 1x CD
6) 1x Remote controller
7) 1x USB cable (for firmware upgrade)

5. PANEL DESCRIPTIONS

Front Panel

graph LR
    A["SIIG® 3x3 4K Video Wall Processor"] --> B["1"]
    B --> C["2"]
    C --> D["3"]
    D --> E["4"]
    E --> F["5"]
    F --> G["6"]
    G --> H["7"]
    H --> I["8"]
    I --> J["9"]

1. Input status light: the selected source has green light
2. Source: Short press to select source from Type-C→VGA→DP→HDMI Input
3. Up: Long press to choose device setting in the OSD menu
4. Down: Long press to choose device setting in the OSD menu
5. Menu/Left: Long Press to return to the main menu, short press to back to previous menu
6. Enter/Right: Short press to enter the sub-menu, if there is no sub menu, short press it to confirm the setting selection
7. Firmware port: Use USB cable to upgrade firmware
8. IR: Receive the IR signal from the remote controller to control the device
9. Power: Turn on or turn off the power

Note: 1. Long press "Up" and "Down" together for 5 seconds can modify the output format, the current input status indicator flashes at a frequency of 5Hz , and then cyclically switches at 1.5S intervals. The four indicators correspond to a resolution of 4k30-1080p-720p-auto.

1. Long press "Menu" and "Enter" together for 5 seconds, the input status lights starts blinking, after the blinking is over, the device is reset successfully.

Rear Panel

1 2 3 4 5 6 7 8 9 10 11 DCS4V TOMC-31 TOM-32 AMD-33 GPS HDMI HDMI-34 HDMI-35 HDMI-36 HDMI-37 HDMI-38 HDMI-39 HDMI-40 HDMI-41 HDMI-42 HDMI-43 HDMI-44 HDMI-45 HDMI-46 HDMI-47 HDMI-48 HDMI-49 HDMI-50 HDMI-51 HDMI-52 HDMI-53 HDMI-54 HDMI-55 HDMI-56 HDMI-57 HDMI-58 HDMI-59 HDMI-60 HDMI-61 HDMI-62 HDMI-63 HDMI-64 HDMI-65 HDMI-66 HDMI-67 HDMI-68 HDMI-69 HDMI-70 HDMI-71 HDMI-72 HDMI-73 HDMI-74 HDMI-75 HDMI-76 HDMI-77 HDMI-78 HDMI-79 HDMI-80 HDMI-81 HDMI-82 HDMI-83 HDMI-84 HDMI-85 HDMI-86 HDMI-87 HDMI-88 HDMI-89 HDMI-90 HDMI-91 HDMI-92 HDMI-93 HDMI-94 HDMI-95 HDMI-96 HDMI-97 HDMI-98 HDMI-99 HDMI-100

1. DC24V2A input
2. Type-C input port
3. VGA input port
4. Audio input port for VGA source
5. DP input port
6. HDMI input port
7. HDMI loop output
8. S/PDIF output port
9. Analog Stereo output port
10. RS232 port
11. TCP/IP port
12. HDMI output1 to HDMI output9 ports

6. CONNECTING AND OPERATING

1) Connect the sources into the video wall controller and Press the button on the remote, then choose the input Signal (USB TYPE-C; VGA; DP; 2 HDMI in).
2) Connect HDMI OUT to display equipment.
3) Power on the Video Wall Controller.
4) Control the Video Wall Controller by Panel button / Remote /RS232 Command.

☆ 3x3 Video Wall Displaying

Remote SIIG® 3x3 4K Video Wall Processor Power Supply Notebook Type-c in PC VGA in Audio in OP in Blue-Ray Player Display Amplifier HDMI in HDMI Loop out SPDIF out Audio out DC/24V Type C in VGA In Audio In OP In HDMI In HDMI Loop SPDIF Out Audio Out RS-232 HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI OUT HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI Out HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI IN HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In HDMI In

☆ 6x4 Video Wall Displaying

Remote 3x3 4K Video Wall Processor Power Supply Notebook PC Blue-Ray Player Amplifier Type-in VGA in Audio out DIP in HDMI in HDMI LOOP out SPDBF out Audio out HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMI OUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIOUT HDMIIN HDMIIN Audiin BP in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 400 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 401 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 402 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 403 in 404 in 404 in 404 in 404 in 404 in 404 in 404 in 404 in 404 in 404 in 405 in 405 in

7. CONTROL INSTRUCTION

7.1 Remote Control

1 2 3 4 5 6 7 8 ALL 9 10 Back 11 12 1 2 3 4 5 6 7 8 9 0 -/-

1. Power on/off

2. Mute

3. Source switching

4. Switch signal source of IN1 (TYPE C)

5. Switch signal source of IN2 (VGA)

6. Switch signal source of IN3 (DP)

7. Switch signal source of IN4 (HDMI)

8. Menu

9. ▲: UP ▼: Down ◀: Left/Menu ▶: Right/Enter, OK: Right/Enter

10. Display and hide OSD menu

11. Return to menu interface

12. 1-4: select the input source IN1---IN4

Note 1: ⑨ The function of Right/Enter in the remote controller is the same as the "Right/Enter" key on the panel.

7.2 Video switching operation

Press the "Source" button to select the input from Type-C→VGA→DP→HDMI.

Note: 1. The video switching OSD interface only shows nine output channels and the current input signal channels, and it can only switch one input source to all output channels when the input and output are both connected to the device.

1. No operation for 20S, the OSD interface turns black, press any button to wake it.

Output 1 2 3 4 5 6 7 8 9 Input 1 1 1 1 1 1 1 1 1

Out 1 1080P@60 (Auto) N_PCM In 3 No SIGNAL

Menu 1/3 Video Audio System > 0/7 Switching Video Wall Mirror Rotate Edge Set > >

OSD video menu

7.2.1 Video Switching

Press the "Left/Menu" on the panel to enter the "Switching" menu, Press the "Right/Enter" on the panel to select and confirm the input source, The selected one has a "@" to mark.

In1→Type-C input, In2→VGA input, In3→DP input, In4→HDMI, the default input is HDMI.

Menu > Video 1/7 0/4 Switching > In 1 Video Wall > In 2 Mirror > In 3 Rotate > In 4 Edge Set >

Menu > Video > Switching > In 1 @ In 2 In 3 In 4

Video switching interface

7.2.2 Video Wall Setting

Press the "Left/Menu" on the panel to enter the "Video Wall" menu,

"Preset": Including 17 kinds of common scenes such as 2x2, 1x4,4x1,4x2 and so on, The selected one has a "@" to mark.

"Set Up": Press the "Right/Enter" on the panel to enter the "Set up" menu, Press the "Up" or "Down" on the panel to select, then press "Enter" to confirm, The selected one has a "@" to mark.

"H_NUM" represents the total amount of display on the horizontal axis, "V_NUM" represents the total amount of display on the vertical axis, "Cascade" represents which cascading level the device is, support 12 layers in total, "Port Map" represents each display corresponding to which HDMI output port.

Menu > Video 2/7 0/2 Switching > Preset > Video Wall > Set Up > Mirror > Rotate > Edge Set >

Menu > Video > Video Wall > 1/2 0/17 Preset > 1x1 @ Set Up > 2x2 4x1 1x4 3x2_1

Preset video wall mode

Menu > Video > Video Wall > 2/2 0/4 Preset > H_NUM > Set Up > V_NUM > Cascade > Port Map >

Video wall set up

7.2.3 Mirror

Press the "Left/Menu" on the panel to enter the "Mirror" menu, Press the "Up" or "Down" on the panel to select, then press "Enter" to confirm, The selected one has a "@" to mark.

"Normal" represents default mode (without mirror function),

"Only X" represents horizontal mirror,

"Only Y" represents vertical mirror,

"X and Y" equals to 180degree rotation.

Menu > Video > 3/7 0/4 Switching > Normal @ Video Wall > Only X Mirror > Only Y Rotate > X and Y Edge Set >

Menu > Video > Mirror > 0/4 Normal @ Only X Only Y X and Y

Mirror interface

7.2.4 Rotate

Press the "Left/Menu" on the panel to enter the "Rotate" menu,

Each output image support 180degree rotation, select "Yes" or "No" to set up,

The selected one has a "@" to mark.

Menu > Video > 4/7 Switching > Out 1 > Video Wall > Out 2 > Mirror > Out 3 > Rotate > Out 4 > Edge Set > Out 5 >

Menu > Video > Rotate > 1/5 Out 1 > No @ Out 2 > Yes Out 3 > Out 4 > Out 5 >

Video > Rotate > Out 1 > No @ Yes

Rotate interface

7.2.5 Edge

Press the "Left/Menu" on the panel to enter the "Edge Set" menu,

Press the "Up" or "Down" on the panel to select, then press "Enter" to confirm,

The selected one has a "@" to mark.

"X" represents the margin setting between the horizontal displays, each image is divided into 302 units.

"Y" represents the margin setting between the vertical displays, each image is divided into 302 units.

The default margin of booth horizontal and vertical display screen is 3.5mm frame size.

Menu > Video > 5/7 0/2 Switching > X > Video Wall > Y > Mirror > Rotate > Edge Set >

Menu > Video > Edge Set > 1/2 0/301 X > 14 Y > 16 18 20 22 @

Video > Edge Set > X > 12/301 14 16 18 20 22 @

Edge set interface

7.2.6 Format

Press the "Left/Menu" on the panel to enter the "Format" menu,

Format including 4K30; 1080P@60; 720P@60; 2560x1440; 1920x1200; 1366x768 and Auto for each output or all outputs to choose by pressing the "Up" or "Down" button, press "Enter" to confirm the selection,

Default is Auto format, The selected one has a "@" to mark.

Menu > Video > Format > 1/5 0/7 Out 1 > 4K30 @ Out 2 > 1080P@60 Out 3 > 720P@60 Out 4 > 2560 x 1440 Out 5 > 1920 X 1200

Video > Format > Out1 > 1/7 4K30 @ 1080P@60 720P@60 2560 x 1440 1920 X 1200

Format interface

7.2.7 EDID

Press the "Left/Menu" on the panel to enter the "EDID" menu,

Press the "Up" or "Down" on the panel to select, press the "Enter" to confirm the selection, the selected one has a "@" to mark.

EDID including "4k30hz" and "1080p@60" for each input or all inputs to choose,

Default is "4k30hz"

Menu > Video > EDID > 1/5 0/2 Type-C > 4K30 @ VGA > 1080P@60 DP > HDMI > ALL

Video > EDID > Type-C > 1/2 4K30 @ 1080P@60

EDID interface

7.3. Audio Setting

7.3.1 Audio input setting

Press the "Left/Menu" on the panel to enter the "Audio" menu,

Press the "Up" or "Down" on the panel to select, press the "Enter" to confirm the selection, the selected one has a "@" to mark,

For HDMI input, there is "CH2.0" and "CH5.1" to choose, default

is CH2.0, Support digital audio 5.1 channel only when input is HDMI.

Menu > Audio > In4(HDMI) > 1/2 CH2.0 @ CH5.1

Audio input setting interface

7.3.2 Audio output setting

Press the "Left/Menu" on the panel to enter the "Audio" menu,

Press the "Up" or "Down" on the panel to select, press the "Enter" to confirm the selection, the selected one has a "@" to mark.

For each output or all outputs, there are "Mute" and "Delay" to choose, The default settings is Unmute and Delay 30ms.

Audio > Out_Set > Out1 > 2/2 0/26 Mute > Mute Delay > Unmute @

Audio > Out_Set > Out1 > 1/2 0/26 Mute > 0 Delay > 10 20 30 @ 40

Audio output setting interface

7.4. System Setting

7.4.1 Baud rate

Press the "Left/Menu" on the panel to enter the "Setup" menu then the "Baud" menu, Press the "Up" or "Down" on the panel to select, then press the "Enter " to confirm, The selected one has a "@" to mark.

It contains 4 kinds of Baud rate including "115200/57600/19200/9600" to choose.

Menu > System > Setup > 1/4 0/4 Baud > 115200 @ TCP/IP > 57600 Reboot > 19200 Factory > 9600

Baud rate interface

7.4.2 TCP/IP setting

Press the "Left/Menu" on the panel to enter the "TCP/IP" menu,

Press the "Up" or "Down" on the panel to select, then press the "Enter " to confirm, The selected one has a "@" to mark.

It contains set up for " DHCP ON/OFF "; "IP Address"; Mask"; "GW"; "DNS",

Eg: IP address setting:

1. Modify the IP to 192.168.1.110, press the "up" and "down" to select IP [0], IP [1], IP [2], and IP [3] to enter the next sub-item (each sub-item can be set from 0 to 255), press the the "up" and "down" again to select "192", "168", "1", and "110" respectively, and click "ENTER" to confirm.
2. After confirming the IP address, press the "up" and "down" keys to select "Apply", and press the "ENTER" to enter and select "YES" to check whether the modification is successful.

Note: 1. The operation steps of IP / MASK / GW / DNS setting are basically the same;
2. The above parameters can be modified manually under static DHCP, otherwise it cannot be modified.
3. The modified parameters need to conform to the network protocol, otherwise it cannot be modified and it will only display "Setting IP error" in the interface.

Menu > System > Setup > 2/4 Baud > 0/6 DHCP > TCP/IP > IP > Reboot > Mask > Factory > GW > DNS >

TCP/IP main interface

System > Setup > TCP/IP > 1/6 0/2 DHCP > OFF @ IP > ON Mask > GW > DNS >

DHCP ON/OFF

System > Setup > TCP/IP > 2/6 0/4 DHCP > IP[0] > IP > IP[1] > Mask > IP[2] > GW > IP[3] > DNS >

IP address

System > Setup > TCP/IP > 2/6 0/4 DHCP > Mask[ 0 ] > IP > Mask[ 1 ] > Mask > Mask[ 2 ] > GW > Mask[ 3 ] > DNS >

Mask address

System > Setup > TCP/IP > 2/6 0/4 DHCP > GW[0] > IP > GW[1] > Mask > GW[2] > GW > GW[3] DNS >

Gateway address

System > Setup > TCP/IP > 2/6 0/4 DHCP > DNS[0] > IP > DNS[1] > Mask > DNS[2] > GW > DNS[3] > DNS >

DNS Interface

7.4.3 Reboot

Press the "Left/Menu" on the panel to enter the "Reboot" menu,

Press the "Up" or "Down" on the panel to select "Yes" or "No", then press the "Enter" to confirm, the selected one has a "@@" to mark.

Menu > System > Setup > 2/4 0/2 Baud > No @ TCP/IP > Yes Reboot > Factory >

Reboot interface

7.4.4 Factory reset

Press the "Left/Menu" on the panel to enter the "Factory" menu,

Press the "Up" or "Down" on the panel to select "Yes" or "No", then press the "Enter" to confirm, the selected one has a "@" to mark.

Menu > System > Setup > 2/4 0/2 Baud > No @ TCP/IP > Yes Reboot > Factory >

Factory reset interface

7.4.5 System information

Press the "Left/Menu" on the panel to enter the "INFO" menu, Press the "Enter" to check the current setting of the device, It Contains "System" and "IP" specific information.

Menu > System > 2/2 Setup > System INFO. > IP

Info interface

Menu > System > INFO. > 1/2 System > CO.XXX IP Type 3x3 VIDEO WALL Ver V0.0.1.8

System information

Menu > System > INFO. > 2/2 DHCP OFF System > IP 192.168.1.168 IP > MASK 255.255.255.0 GW 192.168.1.1 MAC:4658-4EXX-XXXX

IP information

7.5. Web Control

The host computer such as PC is connected to the control device through the TCP/IP network port.

The control mode is divided into two types: connect with a computer without network for single device control or connected to the LAN to realize multi-machine control simultaneously

Control without network:

When the host computer is connected to a computer without network through the TCP/IP port, the host computer is consistent with the control computer network segment. It can be controlled by direct connection; when the network segment is inconsistent, the network segment should be same for the control computer as the host computer

Default IP address:192.168.1.168

Default MASK:255.255.255.0

Default GW:192.168.1.1

MAC:4658-4Exx-xxxx

Internet Protocol Version 4 (TCP/IPv4) Properties General You can get IP settings assigned automatically if your network supports this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. Obtain an IP address automatically Use the following IP address: IP address: 192 . 168 . 1 . 8 Subnet mask: 255 . 5 . 255 . 0 Default gateway: . Obtain DNS server address automatically Use the following DNS server addresses: Preferred DNS server: . Alternate DNS server: . Validate settings upon exit Advanced... OK Cancel

Connecting to LAN to realize multi-user remote control devices (such as mobile phone, other PC) in Ethernet environment, it is necessary to ensure that the IP segment of the host is consistent with that of the connected LAN, it also need to open the DHCP and enter the related IP address to control

graph TD
    A["TCP/IP"] -->|CAT5e/6| B["Router"]
    C["Internet"] --> B
    D["CELL PHONE"] --> B
    E["P C"] --> B

7.5.1 Interface introduction

192.168.1.168 VIDEO AUDIO SYSTEM Video Wall Video Map 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 Video Wall Output: Horizontal 10 + Vertical 1 + Equipment cascade 1 + Input: Type-C VGA DP HDMI Apply

Status display instructions:

(1) Click the navigation bar above, then enter the corresponding operation interface.
(2) Do not click continuously; Click again after the setting is successful. If the setting is invalid, please click the button again.

(1) Use the browser such as Google, Firefox, apple with the latest browser version for better compatibility, the other browsers may result in incompatible problems.
(2) If you use the Internet explorer browser, pls make use the version number is higher than IE10.
(3) The display effect is different in each browser.
(4) If the settings are invalid or error, refresh the page and get latest data again.

Login in method

Default IP login in: use the correct account and password to enter the interface

Note: a. This web has cookies, when the password and account are correct while the browser is not closed, If the user refresh the page again, it will log in automatically.

b. After changing the IP account or password, when you log in again, please use the new IP, account and password to log in again.

LOG IN admin Log in

Operating instructions

Take the default IP address login as an example:

(1) IP configuration: IP configuration is required, whether using single device control or LAN multi-device control
(2) After configuration, pls enter the default IP address into the browser, enter the web end login interface, enter account number: admin, password: admin click on the "Log in" of the yellow bar below the account, as shown in the figure;

7.5.2 Video wall setting

VIDEO Video Wall Mirror Rotate Edge Format EDID AUDIO SYSTEM Video Wall Video Map 1 2 3 4 5 6 7 8 9 10 1 Out Out Out 2 Out Out Out 3 Out Out Out 4 5 6 7 8 9 10 Video Wall Output: Horizontal 3 + Vertical 3 + Equipment cascade 1 + Input: Type-C VISA DI HCIAR Apply

Note: This interface is used to set up video walls or cascade.

Interface introduction:

(1) Video Map column: to identify the location of the output port mapping, you can change the output port position through the drop-down menu. The position of Map1 to Map9 in the same cascading layer is stable no matter how the output ports arrayed, the rule for "Port Map" is from left to right, from top to bottom as showed in the below picture.
(2) Output column: screens in horizontal and vertical directions, plus the parameters of the equipment cascade layers.
(3) Input column: source selection for the video wall. (Type-C, VGA, DP, HDMI).
(4) Default 3x3 video wall, the device can also realize 4x3 5x4 5x5 6x6 7x7 8x8 and max 10x10 video walls through cascade.
(5) The max screen amount in the horizontal direction is 10pcs.
(6) The max screen amount in the vertical direction is 10pcs.
(7) The max cascade layer amount is 12 layers.
(8) Note: The parameters can be set up by clicking the "+" or "-" button in the Output column. The Input column. When one of the Input key is blue, it indicates that the related input signal is successfully connected.

Operating instructions

Eg1: Select DP port as input source to make a 3x3 video wall by 1pcs device.

(1) In the Output section, select both the "Horizon" and "Vertical" as number 3, and the "Equipment Cascade" as number 1 (There is only one device. The cascade position must be 1, otherwise the setting is invalid).
(2) Then select "DP" in the Input section and click "apply".
(3) Click the Video Map column and set the output ports according to TV 1 \~ 9. For Example: In the Video Map column, click and select the output ports as following picture: Out-1:Map5; Out-2:Map4, Out-3:Map3; Out-4:Map8, Out-5: Map7; Out-6: Map2; Out-7: Map9; Out-8 Map1; Out-9: Map6.

Note: 1. Screens under the same cascade layer can be connected to any output port in this layer.

1. The position of Map1 to Map9 is fixed as the example, while there are no limitations for the HDMI output ports order, the corresponding output port can be seen in the OSD.

Map 1 Out 8 Map 2 Out 6 Map 3 Out 3 Map 4 Out 2 Map 5 Out 1 Map 6 Out 9 Map 7 Out 5 Map 8 Out 4 Map 9 Out 7

Eg2: Select HDMI port as input source to make a 4x3 video wall by 2 devices. Operation Steps of device1:

(1) In the Output section of the first device, select the "Horizon" as number 4, "Vertical" as number 3, and the "Equipment Cascade" as number 1, which stands for the device is in the first cascading layer.
(2) Then select "HDMI" in the Input section and click "apply".

Operation Steps of device2:

(3) In the Output section of the second device, select the "Horizon" as number 4, "Vertical" as number 3, and the "Equipment Cascade" as number 2, which stands for the device is in the second cascading layer.
(4) Select the input port as the HDMI Loop out of the device1, then click "apply".

7.5.3 Mirror

Mirror Video All Horizontal Horizontal Vertical Vertical Horz and Vert Hertz/Vert Defaults Default

Interface introduction:

Click the "Mirror" in the navigation bar on the left. The interface has only one section to adjust the Horizontal /Vertical/Both Horizontal and Vertical/ Default.

Note: You can only choose one option at each time.

Operating instructions

Click on the corresponding button to send instructions.

7.5.4 Rotate

Video Video Wall Mirror Rotate Edge Format EBID AUDIO SYSTEM Rotate Video All: Output 1 OFF Output 2 OFF Output 3 OFF Output 4 OFF Output 5 OFF Output 6 OFF Output 7 OFF Output 8 OFF Output 9 OFF All OFF

Interface introduction:

The interface supports each output image 180degree rotation, support rotate a single image at a time or rotate all output images at once.

Operating instructions

Click on the "ON/OFF" button to adjust.

7.5.5 Edge

Video Video Wall Mirror Rotate Edge Format EBD AUDIO SYSTEM Edge Adjustment Video Alt: Horizontal: - 2 + Vertical: - 2 + Defaults: Default

Interface introduction:

The default edge of booth horizontal and vertical display screen is 3.5mm frame size, each image is divided into 302 units.

Operating instructions

Click on the "+/-" button on both Horizontal and Vertical to adjust.

7.5.6 Format

Format Set up Output: 4K >> 01 1080*60 => 02 720*60 => 03 1920x1200 => 04 1356x768 => 05 Auto => 06 Auto => 07 Auto => 08 Auto => 09 ALL Format: 4K30 1080*60 720*60 2550x1440 1920x1200 1356x768 Auto Apply

Interface introduction:

The interface is used to adjust the output format, the left output section including HDMI Output1 to HDMI Output9 and ALL (stands for all HDMI outputs), the right format section including 4K@30Hz、1080P@60Hz、720P@60hz、2560x1440、1920x1200、1366x768 and AUTO.

Operating instructions

E.g.: Select all output format as 4k@30HZ

Click on the "ALL" button in the output section first, then select the "4K30" button in the format section, click "Apply" to confirm.

7.5.7 EDID

EDID Control Video All Input: 1080P->Type- C 1080P->DP (580P->HDU) ALL EDID: Default-4K3D Default-1080P Apply

Interface introduction:

The interface is to set up the EDID for each input port or all the input at once.

INPUT Section: the back content of the ">>" indicates the input source, and the front content of the ">>" indicates the current EDID information. It support set up the EDID separately for each input or select all input as the same EDID.

EDID Section: There are two built-in EDID including 4K@30hz and 1080P.

Operating instructions

Select the input source that needs to change the EDID in the INPUT section ("ALL" means select all input sources), the bottom of the input source is blue;

Select the EDID need to be used in the EDID section and click "Apply" to complete the setting.

7.5.8 Audio output setting

Audio Output: Output 1 Audio Delay Output 2 Audio Delay Output 3 Audio Delay Output 4 Audio Delay Output 5 Audio Delay Output 6 Audio Delay Output 7 Audio Delay Output 8 Audio Delay Output 9 Audio Delay Output All Audio Delay

Interface introduction:

The interface is used to switch and delay the audio of one output or all outputs.

means the audio is turned off,

means the audio is turned on. The default

audio is turned on, and the delay is 30ms.

Operating instructions

Click on the "-/+" button to adjust delay time; options from 0 to 250, per unit is 10ms;

Click on the or button to choose mute or unmute.

7.5.9 Audio input setting

VIDEO AUDIO Audio Output Audio Input SYSTEM Audio Input HDMI(input 4) 2.0 5.1

Interface introduction:

It shows PCM2.0 and 5.1 to choose for HDMI Input.

Operating instructions

Click on the "2.0/5.1" button separately to select the audio format for HDMI input.

7.5.10 Network interface

VIDEO AUDIO SYSTEM Network Reset Password Network Information Mac Address : IP Address : Net Mask Address : Gate Way Address : DHCP : Off Apply

Interface description:

It used to set up and display the basic information including IP/ MAC address, Net mask address, gate way address and DHCP.

Operating instructions:

MAC address: can only be displayed, cannot be modified.

Static IP: Default DHCP OFF.

Dynamic IP: click the "DHCP" button to open the DHCP. The following IP address and other information can not be modified, but current IP address information can be displayed.

7.5.11 Reset

VIDEO AUDIO SYSTEM Network Reset Password Reset Reboot Factory

Interface introduction:

The interface is used to restart the device and restore factory settings.

Operating instructions

Click on each function button to achieve its function (as shown in the figure above), the bottom of the selection is blue.

7.5.12 Password

VIDEO AUDIO SYSTEM Network Reset Password Password Change Password: User Name : New Password : Confirm the Password : Version HTML:0.1.0 Apply

Interface description:

It use to change the login password. You can only change the current login account password.

Default account passwords: admin

Operating instructions:

When you change your account and password, it can support only 5-15 digits, alphanumeric and underlined.

(It only support change the account name and password of the currently logged in account, which will take effect next time).

8. RS232 CONTROL

Function description: plug in the USB port to RS232 tool, double-click to open the RS-232 software. Baud rate: 115200.

Instructions:

1. All instructions begin with "#".

Instruction header c%: d---operation parameter, I---operation lock,

1. " _" means underline, indispensable.

Primary parameter d%: 0---all outputs, 1-x---indicates outputs (1-9), secondary parameters are the same as the first.

1. A space should be added between the instruction header, first-level parameters and attribute parameters. Please check the instruction sheet for property parameters.

Note: "/" indicates that this parameter is not used.

For RS232 command details, pls refer to the document in CD.

9 FIRMWARE UPDATE

9.1 MCU update

Open the software UART_ISP.exe on the PC, select the correct port and baud rate 115200, enter A1_01 (_represents space) in the port, then select the program (xxx.bin) in the path, and click update to complete the upgrade.

UART_ISP V1.1 COM COM5 USB Serial Port PORT A1_01 PATH C:\ BAUD 115200 REFRESH ... UPDATA UART_ISP V1.1 2018-07-12 Steps : 1.Refresh the serial com; 2.Select com, baud, port; 3.Select firmware or drag to this software; 4.Upgrade; Note : 1.You need to disconnect from other devices before upgrading; 2.Do not interrupt the upgrade when upgrading, otherwise the device may be damaged;

9.2 GUI Update

Open the software UART_ISP.exe on PC, select the correct port and baud rate 115200, enter F0_01 (_ represents space) in the port, then select the program (xxxx.bin) in the path, and click update to complete the upgrade.

Note: Please reboot the device after GUI Update.

UART_ISP V1.1 COM COM5 USB Serial Port BAUD 115200 PORT F0_01 REFRESH PATH C:\ ... UPDATE UART_ISP V1.1 2018-07-12 Steps : 1.Refresh the serial com; 2.Select com, baud, port; 3.Select firmware or drag to this software; 4.Upgrade; Note : 1.You need to disconnect from other devices before upgrading; 2.Do not interrupt the upgrade when upgrading, otherwise the device may be damaged;

MAINTENANCE

Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to clean this unit.

PRODUCT SERVICE

1) Damage requiring service:

The unit should be serviced by qualified service personnel if:

(a) The DC power supply cord or AC adaptor has been damaged;
(b) Objects or liquids have gotten into the unit;
(c) The unit has been exposed to rain;
(d) The unit does not operate normally or exhibits a marked change in performance;
(e) The unit has been dropped or the cabinet damaged.

1) Servicing Personnel: Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized servicing personnel.

3) Replacement parts: When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.

4) Safety check: After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition.

Support

For more info or tech support

http://www.siig.com/support

Apr, 2020

Copyright © 2020 by SIIG, Inc. All rights reserved.