ST-CM7089 - Coffee maker Saturn - Free user manual and instructions

Product Type	Coffee Maker
Brand	Saturn
Model	ST-CM7089
Dimensions (W x D x H)	Approx. 20 x 25 x 35 cm
Weight	Approx. 1.5 kg
Power Supply	220-240 V, 50/60 Hz
Power Consumption	Approx. 1000 W
Water Tank Capacity	1.2 liters
Max Cup Capacity	10 cups
Brewing System	Drip filter
Filter Type	Permanent filter (reusable) or paper filters (size 4)
Carafe Material	Glass
Keep Warm Function	Yes, automatic keep warm
Auto Shut-off	Yes, after 2 hours
Anti-drip System	Yes, removable filter basket
Water Level Indicator	Yes, on water tank
Cord Length	Approx. 0.8 m
Cleaning	Regular descaling with vinegar or descaler
Safety	Overheat protection, non-slip feet
Spare Parts Availability	Carafe, filter basket, permanent filter available

Frequently Asked Questions - ST-CM7089 Saturn

How do I descale the coffee maker?

Mix equal parts water and white vinegar, fill the tank, run a brewing cycle without coffee. Repeat with clean water twice. Use a descaling solution if preferred.

What kind of filter does it use?

It uses a permanent reusable filter included, or standard paper filters size 4.

Can I brew less than a full pot?

Yes, you can brew any amount up to the tank capacity. The water level indicator helps measure.

How do I clean the carafe?

Wash with warm soapy water and a non-abrasive sponge. Do not immerse the carafe in water if hot.

The coffee maker stops brewing before the tank is empty. Why?

This may indicate a need for descaling. Built-up minerals can block the system. Also check the filter for clogs.

How long does the keep warm function last?

The keep warm function automatically turns off after 2 hours. You can manually switch off earlier.

Can I use ground coffee from a store?

Yes, use medium grind for best results. Do not use ultra-fine coffee as it may clog the filter.

What should I do if the coffee tastes bitter?

Bitter taste often comes from over-extraction. Try using a coarser grind or less coffee grounds. Also check for old coffee.

The coffee maker leaks. What could be wrong?

Check if the carafe is properly placed and the filter basket is correctly seated. Also inspect the water tank for cracks.

How do I replace the permanent filter?

The permanent filter can be washed with soap and water. If damaged, order a replacement from Saturn or compatible brand.

USER MANUAL ST-CM7089 Saturn

Exterior view of a modern espresso machine (no visible text or symbols)

Coffee Maker

Dear Buyer!

We congratulate you on having bought the device under trade name "Saturn". We are sure that our devices will become safe and reliable assistance in your housekeeping.

Avoid extreme temperature

changes. Rapid temperature change (e.g. when the unit is moved from freezing temperature to a warm room) may cause condensation inside the unit and a malfunction when it is switched on. In this case leave the unit at room temperature for at least 1.5 hours before switching it on. If the unit has been in transit, leave it indoors for at least 1.5 hours before starting operation.

Read this booklet thoroughly before using and save it for future reference

IMPORTANT SAFEGUARDS

Before using the electrical appliance, the

following basic precautions should always be followed including the following:

1. Read all instructions.
2. Before using check that the voltage of wall outlet corresponds to rated voltage marked on the rating plate.
3. This appliance has been incorporated with a grounded plug. Please ensure the wall outlet in your house is well earthed.
4. To protect against fire, electric shock and injury to persons do not immerse cord, plug, in water or other liquid.
5. Remove plug from wall outlet before cleaning and when not in use. Allow appliance cool down completely before taking off, attaching components or before cleaning.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, electrical or mechanical adjustment.
7. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.
8. Place appliance on flat surface or table, do not hang power cord over the

edge of table or counter.

1. Ensure the power cord does not touch the hot surface of appliance.

2. In order to avoid to be damaged, do not place the coffee maker on the hot surface or beside fire.

3. To disconnect, remove plug from wall outlet. Always hold the plug. But never pull the cord.

4. Do not use appliance for other than intended use and place it in a dry environment.

5. Close supervision is necessary when your appliance is being used near children.

6. Be careful not to get burned by the steam.

7. Do not touch the hot surface of appliance (such as steam wand, and the steel mesh just boiling). Use handle or knobs.

8. Do not let the coffee maker operate without water.

9. Scalding may occur if the water tank is removed during the brewing cycles.

10. Do not remove the metal funnel when appliance in brewing coffee or when steam and hot water escape from metal funnel and ensure to release the pressure in water tank before removing metal funnel.

11. Connect plug to wall outlet before

using and turn any switch off before plug is removed from wall outlet.

1. Relief pressure through steam wand before removing tank cover or metal funnel.

2. This appliance is not intended for used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety. It is not advised to use this appliance by children under 14.

3. Children should be supervised to ensure that they do not play with the appliance.

4. This appliance is intended to be used in household and similar applications such as:

- staff kitchen areas in shops, offices and other working environments;

- farm houses;

- by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments.

1. Do not use outdoors.

2. Save these instructions.

BEFORE THE FIRST USE

To ensure the first cup of coffee tastes excellent, you should rinse the coffee maker with warm water as follows:

Remove the detachable water tank then pour water into water tank, the water level should not exceed the "MAX" mark in the tank. Then replace the water tank cover.

Note: the appliance is supplied with a detachable tank for easy cleaning, you'd better fill the tank with water first, and then put the tank into the appliance.

Set steel mesh into metal funnel (no coffee in steel mesh), make sure the tube on the funnel aligns with groove in the appliance, then insert the funnel into the appliance from the "Insert" position, and you can fix them into coffee maker firmly through turn it

anticlockwise, until it is at the lock position.

Place an espresso cup (your cup) on removable cup shelf. Make sure the steam control knob is on the minimum position.

Note: the appliance is not equipped with jug, please use your own jug or coffee cup.

Connect to power source, press down the ON/OFF button to the lower position

which is the ON" position. The power indicator (red) will be illuminated.

Press down the pump control button to

the lower position which is the "☐" position, the pump will pump water, when there is water flowing out and close the pump by pressing the pump

control button again to the " ■ " position, make sure the coffee/steam button is on the higher position which is

the position and waiting for a moment, the appliance begins to be pre-heated until the ready indicator (green) is illuminated, it shows the pre-heating is finish. Pressing the pump to

the lower position which is the " " position again, and water will flow out. After water not dropping out any more, you can pour the water in each container out then clean them thoroughly, now you can start brewing.

Note: There may be noise and no water comes out when pump the water on the first time, it is normal, you should turn the steam control knob to the opening position to release the air in the appliance. After about 20s, the noise will disappear, and the water will comes out.

PRE-HEATING

To make a cup of good hot Espresso coffee, we recommend you preheating the appliance before making coffee, including the funnel, filter and cup, so that the coffee flavor can not be

influenced by the cold parts.

Remove the detachable tank and open the tank cover to fill it with desired water, the water level should not exceed the "MAX" mark in the tank. Then place the tank into the appliance properly.

Set steel mesh into metal funnel, make sure the tube on the funnel aligns with groove in the appliance, then insert the funnel into the appliance from the "Insert" position, and you can fix them into coffee maker firmly through turn it anticlockwise until it is at the lock position (See fig. 1).

Place an espresso cup (your cup) on the cup warming plate for warm and dry for collecting coffee later.

1. Then connecting the appliance to power supply source. Make sure the steam control knob is on the minimum position.

Press the ON/OFF button to the lower position which is the "ON" position, the power indicator (red) will be illuminated, make sure the coffee/steam button is on

the higher position which is the position. Press down the pump control button to the lower position which is the

" ” position, when there is water

flowing out, close the pump immediately by pressing the pump control button

again to the higher position of 21 ". The purpose of the step is that pump the water of the tank into the housing. When the ready indicator (green) is illuminated, you should press down the pump control button to the lower

position which is the " 🔍" position again, there will be hot water flowing out. When the ready indicator (green) is extinguished, close the pump by pressing the pump control button again to the higher position of " 🔍". The pre-heating is finished. Before making coffee, first clean out the water in the drip tray.

MAKE ESPRESSO COFFEE

Remove the funnel by turning it in clockwise, add ground coffee to steel mesh with measuring spoon, a spoon ground coffee power can make about a cup of top-grade coffee, then press the ground coffee powder tightly with the tamper.

Set steel mesh into metal funnel, make sure the tube on the funnel aligns with groove in the appliance, then insert the

funnel Into the appliance from the "Insert" position, and you can fix them into coffee maker firmly through turn it anticlockwise until it is at the lock position (See fig. 1).

Remove the cup from the cup warming plate. Then place the hot cup (your cup) on removable cup shelf.

1. At the time, the ready indicator (green) is illuminated, once the green lamp is illuminated, you should press down the pump control button to the

lower position which is the "?" position, waiting for a moment, there will be coffee flowing out.

1. You should press and release the ON/OFF button to the higher position

which is the "■" position manually when desired coffee is obtained or the color of coffee changes weak obviously, the power indicator and ready indicator go out and the coffee maker stops working, your coffee is ready now.

WARNING: Do not leave the maker unattended during making the coffee, as you need operate manually sometimes!

1. After finishing making the coffee, you can take the metal funnel out through turn clockwise, then pour the coffee residue out with the steel mesh pressed by press bar.
2. Let them cool down completely, then rinse under running water.

FROTHING MILK/ MAKE

CAPPUCCINO

You get a cup of cappuccino when you top up a cup of espresso with frothing milk.

Method:

Prepare espresso first with container big enough according to the part "MAKE ESPRESSO COFFEE", make sure that the steam control knob is at the minimum position.

Press down the coffee/steam button to

the lower position which is the position, waiting for until the indicator (green) is illuminated.

Note: During operation, if the indicator is extinguished, you should turn the steam control knob to OFF

c φdsfiiere Then press and release the coffee/steam button to the higher

position which is the position and press down the pump control to the

lower position which is the "?" position and pump water, after about 30s, close the pump, press down the coffee/steam button to the lower

position which is the position again, then wait for until the green indicator is illuminated and turn the steam control knob in anti-clockwise, the steam will come out again.

Fill a jug with about 100 grams of milk for each cappuccino to be prepared, you are recommended to use whole milk at refrigerator temperature (not hot!).

Note: In choosing the size of jug, it is recommend the diameter is not less than 70 ± 5mm , and bear in mind that the milk increases in volume by 2 times, make sure the height of jug is enough.

Insert the frothing device into the milk about two centimeter, then turn the steam control knob slowly in anticlockwise, steam will come out from the grotheing device. Froth milk in the way moving vessel round from up to down.

Note: Never turn the steam control button rapidly, as the steam will accumulate rapidly in short time which may increase the potential of the risk of explosion.

1. When the required purpose is reached, you can turn the steam control knob to the minimum position.
   Note: Clean steam outlet with wet sponge immediately after steam stops generating, but care not to hurt!
2. Pour the frothed milk into the espresso prepared, now the cappuccino is ready. Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder.
3. Press and release the ON/OFF button to the higher position which is the

OFF "■" position to cut the power source off.

Note: we recommend you make to cool down at least for 5 min before making coffee again. Otherwise burnt odor may occur in your Espresso coffee.

PRODUCING STEAM TO HEAT LIQUIDS

The steam wand (without the frothing device) can be used to make hot beverages like drinking chocolate, water or tea.

Method:

1. Remove the detachable tank and fill it with desired water, the water level should not exceed the "MAX" mark in the tank. Then place the tank into the appliance properly.

2. Then connecting the appliance to power supply source.

3. Press down the ON/OFF button to the

lower position which is the "ON" position, the power indicator (red) is illuminated.

1. Press down the pump control button
   to the lower position which is the "■" position, make sure the coffee/steam button is on the higher position which is

the position, the pump will pump

al I owaterthwhen there is water flowing out, close the pump immediately, pressing down the coffee/steam button to the

lower position which is the position

and waiting for a moment, the appliance begins to be heated until the green lamp is illuminated, it shows the heating is finish.

1. Remove the frothing device from the steam wand.
2. Dip the steam wand into the liquid to be heated. Turn the steam control knob in anti-clockwise slowly to start making steam.
3. When the required temperature is reached, you can turn the steam control knob to the minimum position.
4. Press and release the ON/OFF button to the higher position which is the

"■" position to cut the power source off.

CLEAN AND MAINTENANCE:

Cut off power source and let the coffee maker cool down completely before cleaning.

Clean housing of coffee maker with moisture-proof sponge often and clean water tank, drip tray and removable shelf regularly then dry them.

Note: Do not clean with solvent cleanser. Never immerse the housing in water for cleaning.

Detach the metal funnel through turn it clockwise, get rid of coffee residue

Inside, then you can clean it with cleanser, but at last you must rinse with clear water.

Clean all the attachments in the water and dry thoroughly.

CLEANING MINERAL DEPOSITS

1. To make sure your coffee maker operating efficiently, internal piping is cleanly and the peak flavor of coffee, you should clean away the mineral deposits left every 2-3 months.

2. Fill the tank with water and descaler to the MAX level (the ratio of water and descaler is 4:1, the detail refers to the instruction of descaler. Please use "household descaler", you can use the citric acid (obtainable from chemist's or drug stores) instead of the descaler (the one hundred parts of water and three parts of citric acid).

3. According to the program of pre-heating, put the metal funnel (no coffee powder in it) and carafe (jug) in place. Brewing water per "PRE-HEATING".

4. Press down the ON/OFF button to the

a l c lower o position which is the "ON"

position, the power indicator (red) will be illuminated, you should press the pump control button to the lower

position which is the position, make sure the coffee/steam button is on the

higher position which is the position, when there is water flowing out and close the pump by pressing the pump control button again to the

"■" position, and waiting for a moment, the coffee maker begins to be heated.

1. When the ready indicator (green) is illuminated, it shows the heating is finish. Pressing down the pump control button to the lower position which is the
   " ” position and make two cups coffee (about 20z). Then close the pump and wait for 5s.
2. Press down the coffee/steam button

to the lower position which is the position, waiting for until the green indicator is illuminated. Make steam for 2min, then turn the steam control knob to the minimum position to stop making steam. Press and release the ON/OFF to

the higher position which is the "■" position to stop the unit immediately, make the descalers deposit in the unit

at least 15 minutes.

1. Restart the unit and repeat the steps of 4-6 at least 3 times.
2. Then pressing and release the coffee/steam button to the higher

position which is the ■ position, when the green lamp is illuminated, press down the pump control button to the

lower position which is the "?" position to brew until no descaler is left.
9. Then brewing coffee (no coffee powder) with tap water in the MAX level, repeat the steps of 4-6 for 3 times (it is not necessary to wait for 15 minutes in step of 6), then brewing until no water is left in the tank.
10. Repeat the step of 9 at least 3 times to make sure the piping is cleanly.

TROUBLE SHOOTING

Symptom	Cause	Corrections
Water leaks from the bottom of coffee maker.	There is much water in the drip tray.	Please clean the drip tray.
	The coffee maker is malfunction.	Please contact with the authorized service facility for repairing.
Water leaks out of outer side of filter.	There is some coffee powder on filter edge.	Get rid of them.
Acid (vinegar) taste exists in Espresso coffee.	No clean correctly after cleaning mineral deposits.	Clean coffee maker per the content in “before the first use” for several times.
	The coffee powder is stored in a hot, wet place for a long time. The coffee powder turns bad.	Please use fresh coffee powder, or store unused coffee powder in a cool, dry place. After opening a package of coffee powder, reseal it tightly and store it in a refrigerator to maintain its freshness.
The coffee maker cannot work any more.	The power outlet is not plugged well.	Plug the power cord into a wall outlet correctly, if the appliance still does not work, please contact with the authorized service facility for repairing.
The steam cannot froth.	The steam ready indicator (green indicator) is not illuminated.	Only after the steam ready indicator (green indicator) is illuminated, the steam can be used to froth.
	The container is too big or the shape is not fit.	Use high and narrow cup.
	You have used skimmed milk	Use whole milk or half-skimmed milk

Technical Data:

Power:	1050 W
Rated Voltage:	220-230 V
Rated Frequency:	50 Hz
Rated Current:	4.8 A

Set

Coffee Maker	1
Instruction Manual with Warranty Book	1
Package	1

ENVIRONMENT FRIENDLY DISPO- SAL

You can help protect the environment!

Please	remember	to
respect	the	local

regulations: hand in the non-working electrical equipment to an appropriate waste disposal centre.

The manufacturer reserves the right to change the specification and design of goods.

RU

Кофеварка

The Warranty is provided for the period of 2 years or more if the Law on User Right of the country where the appliance was bought provides for a greater minimum warranty period.

All terms of warranty comply with to the Law on Protection of the Consumer Rights and are governed by the legislation of the country where the product was bought.

The warranty and free of charge repair are provided in any country where the product is delivered to by Saturn Home Appliances or authorized representative thereof, and where no restriction of import or other legal provisions interfere with rendering of warranty services and free of charge repair.

Cases uncovered by the warranty and free of charge repair:

1. Guarantee coupon is filled in improperly.
2. The product has become inoperable because of the Buyer's non-observance of the service regulations indicated in the instruction.
3. The product was used for professional, commercial or industrial purposes (except for the models, specially intended for this purpose that is indicated in the Instruction).
4. The product has external mechanical damage or damage caused by penetration of the liquid inside, dust, insects and other foreign objects.
5. The product has damages caused by non-observance of the rules of power supply from batteries, mains or accumulators.
6. The product was exposed to opening, repair or modification of design by the persons, unauthorized to repair; independent cleaning of internal mechanisms etc. was made.
7. The product has natural wear of parts with limited service life, expendables etc.
8. The product has deposits of scale inside or outside of fire-bar elements, irrespective of used water quality.

9. The product has damages caused by effect of high (low) temperatures or fire on non-heat resistant parts of the product.

10. The product has damages of accessories and nozzles which are included into the complete set of product shipment (filters, grids, bags, flasks, cups, covers, knives, sealing rings, graters, disks, plates, tubes, hoses, brushes, and also power cords, headphone cords etc.).

On the warranty service and repair, please contact the authorized service centers of "Saturn Home Appliances".

CZ

MEZINÁRODNÍ ZÁRUKA

When purchasing the product,

please require its checking before you;

BE SURE

that the goods sold to you, are functional and complete and that the warranty coupon is filled in correctly.

This warranty coupon confirms the absence of any defects in the product you purchased and provides for free of charge repair of the product failed through the fault of the manufacturer throughout the period of warranty service and free of charge repair. Failing the presentation of this coupon, in case of its improper filling in, infringement of factory seals (If any), and also in cases indicated in the warranty obligations, the claims are not accepted, and no warranty service and free of charge repair is made! The warranty coupon is valid only in the original copy with the stamp of trading organization, signature of the seller, date of sale and signature of the buyer.

CZ

ZÁRUČNÍ LIST

Při koupi výrobku

Buyer's Signature confirming the acquaintance and consent with conditions of free of charge maintenance service of the product, and absence of the complaints on appearance and color of the product.