422-207 - Lighting Anslut - Free user manual and instructions

Product Type	Multi-mount lamp (wall, post, standing, suspended)
Model	422-207 (covers 422-205 to 422-210)
Brand	Anslut
Power Supply	Mains (230V), must be connected to earthed outlet
Bulb Type	Incandescent (screw-in, max wattage per type plate)
Material	Plastic (lamp cover, panel), metal (screws, terminal block)
Installation	Wall, post, ground, or ceiling mount with included plastic expanders
Safety Features	Disconnect from mains before installation; do not touch hot bulb; replace broken glass immediately
Maintenance	Replace bulb only when cooled; use dry cloth for cleaning (if needed)
Wiring	Brown (L), Blue (N), Green/Yellow (Earth) to terminal block
Compliance	CE, RoHS (implied by EU sale)
Manual Languages	EN, SV, NO, PL
Spare Parts	Contact service department for replacement parts
Environmental Disposal	Recycle at designated station – do not discard with household waste
Dimensions	Not specified (varies by mounting type)
Weight	Not specified

Frequently Asked Questions - 422-207 Anslut

How do I install the wall lamp (model 422-207)?

First, mount the plastic expander on the wall. Insert two screws into the plastic panel and fit it onto the expander using self-tapping screws. Connect the power cords (brown to brown, blue to blue, green/yellow to earth) in the terminal block, then mount the lamp on the fixed screws and tighten with domed screws. Finally, screw in a bulb without exceeding the maximum wattage on the type plate.

Can I install the lamp outdoors?

Yes, the lamp post option (Figure 2) is designed for mounting in the ground. Ensure all connections are properly sealed against moisture and the power supply is turned off during installation.

What should I do if the glass cover breaks?

Immediately replace the broken glass. Do not use the lamp until the glass is replaced, as it poses a safety risk. Contact your dealer or an authorized service centre for a replacement.

How do I replace the bulb?

Disconnect the lamp from the mains power supply. Open the lamp cover and let the bulb cool completely. Unscrew the old bulb, avoiding touching it with bare hands. Screw in a new bulb of the correct type and wattage (see type plate), then close the cover before switching on.

Why does the lamp get very hot?

The incandescent bulb generates heat when switched on. This is normal. Do not touch the bulb until it has cooled sufficiently. Ensure the lamp is not covered or placed near flammable materials.

What does the earth wire (green/yellow) connect to?

The green/yellow earth wire must be connected to the terminal block with the earth symbol. This ensures the lamp is properly grounded for safety. An earthed power outlet is required.

Can I use an LED bulb instead of incandescent?

The manual specifies only incandescent bulbs. Using an LED bulb may cause compatibility issues or reduced performance. Check the type plate for maximum wattage and consult the manufacturer if unsure.

What should I do if the power cord is damaged?

Do not use the lamp. For safety, the power cord must be replaced only by an authorized service centre. Contact your dealer for assistance.

How do I clean the lamp?

Disconnect from the mains power supply. Let the bulb cool. Use a soft, dry cloth to wipe the exterior. Do not use abrasive cleaners or immerse in water. Avoid touching the bulb with bare hands.

Is the lamp suitable for bathrooms or damp locations?

The manual does not specify an IP rating. The lamp is likely designed for dry indoor or sheltered outdoor use. For damp locations, ensure installation follows local electrical codes and uses appropriate weatherproofing.

USER MANUAL 422-207 Anslut

Installation Instructions for Lamps

422-205 - 422-210

Black decorative street lamp with a lit incandescent light bulb mounted on a wall (no text or symbols visible)

SV Bruksanvisning i original

NO Bruksanvisning i original

EN Installation instructions in original

SÄKERHETSANVISNINGAR

Technical line drawing of a mechanical component with mounting holes and structural ribs (no text or symbols)

Figur 5

Technical line drawing of a lantern with a dome-shaped top and side frame (no text or symbols)

Figur 6

MONTERING

Technical line drawing of a mechanical component with mounting holes and internal channels (no text or symbols)

Rysunek 5

Technical line drawing of a lantern with a dome-shaped top and flared base (no text or symbols)

Rysunek 6

Read these instructions carefully before use!

• Disconnect from the mains power supply before starting installation.
  • The bulb gets very hot when it is switched on. Do not touch the bulb until it has cooled sufficiently.
• The bulb must not exceed the stated maximum output.
• Any lamp glass which breaks must be replaced immediately. Do not use the lamp when the lamp glass is broken.
• Do not look directly into the bulb when it is switched on.
• Note that the fitting must be connected to an earthed power outlet.
• Do not use the lamp if the power cord and/or plug are damaged in any way. For safety reasons, the power cord must only be replaced or repaired by an authorised service centre. Consult your dealer.

DESCRIPTION

Figure 1	Figure 2
Figure 3	Figure 4

Technical line drawing of a mechanical component with no visible text or symbols

Figure 5

Technical line drawing of a decorative lantern with a dome and central hub (no text or symbols)

Figure 6

INSTALLATION

Installation of wall lamp (figure 1)

1. First, mount the plastic expander on the wall where the lamp is to be.
2. Insert two screws in the plastic panel.
3. Fit the plastic panel in the expander using self-tapping screws.
4. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
5. Insert the terminal block in the plastic panel.
6. Mount the lamp on the fixed screws and tighten using domed screws.
7. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

Installation of lamp post (figure 2)

1. Mount the post in the ground.
2. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
3. Insert the terminal block in the post.
4. Mount the lamp on the post using crosshead screws.
5. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

Installation of standing lamp (figure 3)

1. First, mount the plastic expander on the surface where the lamp is to be.
2. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
3. Fit the lamp on the expander using self-tapping screws.
4. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

Installation of suspended lamp (figure 4)

1. Pull the power cord through the chain loop.
2. Secure both ends of the chain loop to the lamp and the fixed panel.
3. Fit the plastic expander on the ceiling-mounted lamp.
4. Insert two screws in the plastic panel.
5. Attach the plastic panel to the ceiling using self-tapping screws.
6. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
7. Insert the terminal block in the plastic panel.
8. Mount the lamp on the fixed screws and tighten using domed screws.
9. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

MAINTENANCE

Replacing the bulb

1. Disconnect from the mains power supply.
2. Open the lamp cover.
3. Unscrew the bulb when it has cooled.
4. Do not touch the bulb with your bare hands.
5. Carefully screw a new bulb into the bulb holder.
6. Put the lamp cover back before switching on the lamp.

Subject to printing errors and design changes over which we have no control. In the event of problems, please contact our service department. www.jula.com

Care for the environment!

Must not be discarded with household waste!

This product contains electrical or electronic components that should be recycled.

Leave the product for recycling at the designated station e.g. the local authority's recycling station.