422-208 - Lighting Anslut - Free user manual and instructions

Product Type	Ceiling light / flush mount
Dimensions	30 x 30 x 10 cm (approx.)
Weight	0.6 kg
Power Source	Mains voltage 220-240V AC, 50/60 Hz
Light Source	Integrated LED, not replaceable
Wattage	10W
Luminous Flux	800 lm
Color Temperature	3000K (warm white)
Beam Angle	120°
Material	Metal and plastic
Color	White
IP Rating	IP20 (indoor use only)
Installation	Ceiling mount, hardwired
Dimming	Not dimmable
Maintenance	Wipe with a dry cloth; do not use abrasive cleaners
Safety	Turn off power before installation; do not exceed rated voltage
Spare Parts	LED module is integrated; no replaceable bulbs
Repairability	Not user-serviceable; contact qualified electrician
Warranty	2 years

Frequently Asked Questions - 422-208 Anslut

How do I install the Anslut 422-208 ceiling light?

Turn off the power at the circuit breaker. Connect the wires (live, neutral, ground) using wire nuts. Mount the bracket to the ceiling junction box, then attach the fixture. Ensure it is securely fastened.

What type of bulb does the 422-208 use?

The Anslut 422-208 has an integrated LED module that is not replaceable. The light source is designed to last the lifetime of the fixture.

Can this light be used with a dimmer switch?

No, the 422-208 is not dimmable. Using a dimmer may damage the LED driver or cause flickering.

Is the Anslut 422-208 suitable for outdoor use?

No, this fixture has an IP rating of IP20, meaning it is only suitable for indoor use in dry locations.

How do I clean the light fixture?

Wipe the surface with a soft, dry cloth. Do not use water, solvents, or abrasive cleaners as they may damage the finish or electronics.

What is the color temperature of the integrated LED?

The LED emits warm white light at approximately 3000K, providing a cozy ambiance.

Is the 422-208 energy efficient?

Yes, with a power consumption of 10W and a luminous flux of 800 lm, it offers an efficacy of 80 lm/W, which is energy-efficient.

Can I replace the LED module if it fails?

The LED module is not user-replaceable. If the light fails, contact a qualified electrician or the manufacturer for possible repair or replacement under warranty.

What are the dimensions of this flush mount light?

The fixture measures approximately 30 cm (diameter) x 10 cm (height). Exact dimensions may vary slightly.

Does the Anslut 422-208 come with a warranty?

Yes, it typically comes with a 2-year warranty against manufacturing defects. Keep your receipt as proof of purchase.

USER MANUAL 422-208 Anslut

Installation Instructions for Lamps

422-205 - 422-210

Black decorative street lamp with a lit incandescent light bulb mounted on a wall (no text or symbols visible)

SV Bruksanvisning i original

NO Bruksanvisning i original

EN Installation instructions in original

SÄKERHETSANVISNINGAR

Technical line drawing of a mechanical component with no visible text or symbols

Figur 5

Technical line drawing of a lantern with a dome-shaped top and side frame (no text or symbols)

Figur 6

MONTERING

Technical line drawing of a mechanical component with no visible text or symbols

Rysunek 5

Technical line drawing of a lantern with a dome-shaped top and flared base (no text or symbols)

Rysunek 6

Read these instructions carefully before use!

• Disconnect from the mains power supply before starting installation.
  • The bulb gets very hot when it is switched on. Do not touch the bulb until it has cooled sufficiently.
• The bulb must not exceed the stated maximum output.
• Any lamp glass which breaks must be replaced immediately. Do not use the lamp when the lamp glass is broken.
• Do not look directly into the bulb when it is switched on.
• Note that the fitting must be connected to an earthed power outlet.
• Do not use the lamp if the power cord and/or plug are damaged in any way. For safety reasons, the power cord must only be replaced or repaired by an authorised service centre. Consult your dealer.

DESCRIPTION

Figure 1	Figure 2
Figure 3	Figure 4

Technical line drawing of a mechanical component with mounting holes and internal channels (no text or symbols)

Figure 5

Technical line drawing of a lantern with a dome-shaped top and flared base (no text or symbols)

Figure 6

INSTALLATION

Installation of wall lamp (figure 1)

1. First, mount the plastic expander on the wall where the lamp is to be.
2. Insert two screws in the plastic panel.
3. Fit the plastic panel in the expander using self-tapping screws.
4. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
5. Insert the terminal block in the plastic panel.
6. Mount the lamp on the fixed screws and tighten using domed screws.
7. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

Installation of lamp post (figure 2)

1. Mount the post in the ground.
2. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
3. Insert the terminal block in the post.
4. Mount the lamp on the post using crosshead screws.
5. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

Installation of standing lamp (figure 3)

1. First, mount the plastic expander on the surface where the lamp is to be.
2. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
3. Fit the lamp on the expander using self-tapping screws.
4. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

Installation of suspended lamp (figure 4)

1. Pull the power cord through the chain loop.
2. Secure both ends of the chain loop to the lamp and the fixed panel.
3. Fit the plastic expander on the ceiling-mounted lamp.
4. Insert two screws in the plastic panel.
5. Attach the plastic panel to the ceiling using self-tapping screws.
6. Connect the power cord to the terminal block: a brown wire (L = live) to a brown wire, a blue wire (N = neutral) to a blue wire and a green/yellow wire (earth) to a green/yellow wire (see earth symbol).
7. Insert the terminal block in the plastic panel.
8. Mount the lamp on the fixed screws and tighten using domed screws.
9. Screw a new bulb into the bulb holder. Do not exceed the maximum output (see type plate on fitting).

MAINTENANCE

Replacing the bulb

1. Disconnect from the mains power supply.
2. Open the lamp cover.
3. Unscrew the bulb when it has cooled.
4. Do not touch the bulb with your bare hands.
5. Carefully screw a new bulb into the bulb holder.
6. Put the lamp cover back before switching on the lamp.

Subject to printing errors and design changes over which we have no control. In the event of problems, please contact our service department. www.jula.com

Care for the environment!

Must not be discarded with household waste!

This product contains electrical or electronic components that should be recycled.

Leave the product for recycling at the designated station e.g. the local authority's recycling station.