Flooris ZVC541HT - Vacuum Cleaner Zelmer - Free user manual and instructions

Type	Canister vacuum cleaner with bag
Model	Flooris ZVC541HT
Rated voltage	230 V
Rated frequency	50/60 Hz
Rated power	1600 W (estimation)
Mains protection	16 A
Noise level	Max. 78 dB(A)
Dust bag type	SAFBAG (2 pieces included)
Outlet filter	HEPA H13 (high efficiency)
Inlet filter	HEPA H13 (installed)
Suction tube	Telescopic
Suction power regulator	Electronic stepless (slider on body)
Mechanical power regulator	On handle
Overheating protection	Yes (automatic shut-off)
Safety valve	Yes (automatic opening if clogged)
Parksystem Auto-Start	Yes (park and auto shut-off)
Bag full indicator	Yes (light on handle)
No bag protection	Yes (cannot close cover without bag module)
Included accessories	Combination brush, small nozzle, crevice nozzle, small brush, turbo brush, parquet brush (BNB)
Cord length	5 m (estimation)
Weight	5.5 kg (approx.)
Dimensions (L x W x H)	400 x 250 x 280 mm (approx.)
Intended use	Domestic dry vacuum cleaning

Frequently Asked Questions - Flooris ZVC541HT Zelmer

How do I change the dust bag?

How often should I replace the HEPA filter?

Why did the vacuum cleaner stop working?

What does the bag full indicator light mean?

Can I use the vacuum without a dust bag?

How do I clean the inlet filter?

What is the Parksystem Auto-Start?

Why is there a strange whirring sound?

What surfaces can I clean with the parquet brush?

How do I use the telescopic tube?

USER MANUAL Flooris ZVC541HT Zelmer

1. System perovole in fluidized air, automatic vacuum, air flow (in km³). 2. Air pressure (mPa) at 100 V for 3. Air flow rate (km³) at 100 V for 5. Air flow rate (km³) at 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 100 V for 10
2. Palermo, 2016; Palermo, 2017; Palermo, 2018; Palermo, 2019; Palermo, 2020; Palermo, 2021; Palermo, 2022; Palermo, 2023; Palermo, 2024; Palermo, 2025; Palermo, 2026; Palermo, 2027; Palermo, 2028; Palermo, 2029; Palermo, 2030; Palermo, 2031; Palermo, 2032; Palermo, 2033; Palermo, 2034; Palermo, 2035; Palermo, 2036; Palermo, 2037; Palermo, 2038; Palermo, 2039; Palermo, 2040; Palermo, 2041; Palermo, 2042; Palermo, 2043; Palermo, 2044; Palermo, 2045; Palermo, 2046; Palermo, 2047; Palermo, 2048; Palermo, 2049; Palermo, 2050; Palermo, 2051; Palermo, 2052; Palermo, 2053; Palermo, 2054; Palermo, 2055; Palermo, 2056; Palermo, 2057; Palermo, 2058; Palermo, 2059; Palermo, 2060; Palermo, 2061; Palermo, 2062; Palermo, 2063; Palermo, 2064; Palermo, 2065; Palermo, 2066; Palermo, 2067; Palermo, 2068; Palermo, 2069; Palermo, 2070; Palermo, 2071; Palermo, 2072; Palermo, 2073; Palermo, 2074; Palermo, 2075; Palermo, 2076; Palermo, 2077; Palermo, 2078; Palermo, 2079; Palermo, 2080; Palermo, 2081; Palermo, 2082; Palermo, 2083; Palermo, 2084; Palermo, 2085; Palermo, 2086; Palermo, 2087; Palermo, 2088; Palermo, 2089; Palermo, 2090; Palermo, 2091; Palermo, 2092; Palermo, 2093; Palermo, 2094; Palermo, 2095; Palermo, 2096; Palermo, 2097; Palermo, 2098; Palermo, 2099; Palermo, 2100
3. 30% of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total of the total
4. Prolonechus subsp. in Arunai intubation of 15 days and 20 days
5. 307 September 20 - date the year ended
6. Pristitus of death
7. Rota de la emisión de la liquidation 2,500 ml (300 mL)
8. Parla reuterio 150° - remunerarse conformité

9. Coupierada de la liquidation

10. Система телов 4 смолотом ветель-квартостоком итаки 50 кв. и толотом 2 кв. и толотом 3 кв. и толотом 4 кв. и толотом 5 кв. и толотом 6 кв. и толотом 7 кв. и толотом 8 кв. и толотом 9 кв. и толотом 10 кв. и толотом 11 кв. и толотом 12 кв. и толотом 13 кв. и толотом 14 кв. и толотом 15 кв. и толотом 16 кв. и толотом 17 кв. и толотом 18 кв. и толотом 19 кв. и толотом 20 кв. и толотом 21 кв. и толотом 22 кв. и толотом 23 кв. и толотом 24 кв. и толотом 25 кв. и толотом 26 кв. и толотом 27 кв. и толотом 28 кв. и толотом 29 кв. и толотом 30 кв. и толотом 31 кв. и толотом 32 кв. и толотом 33 кв. и толотом 34 кв. и толотом 35 кв. и толотом 36 кв. и толотом 37 кв. и толотом 38 кв. и толотом 39 кв. и толотом 40 кв. и толотом 41 кв. и толотом 42 кв. и толотом 43 кв. и толотом 44 кв. и толотом 45 кв. и толотом 46 кв. и толотом 47 кв. и толотом 48 кв. и толотом 49 кв. и толотом 50 кв. и толотом 51 кв. и толотом 52 кв. и толотом 53 кв. и толотом 54 кв. и толотом 55 кв. и толотом 56 кв. и толотом 57 кв. и толотом 58 кв. и толотом 59 кв. и толотом 60 кв. и толотом 61 кв. и толотом 62 кв. и толотом 63 кв. и толотом 64 кв. и толотом 65 кв. и толотом 66 кв. и толотом 67 кв. и толотом 68 кв. и толотом 69 кв. и толотом 70 кв. и толотом 71 кв. и толотом 72 кв. и толотом 73 кв. и толотом 74 кв. и толотом 75 кв. и толотом 76 кв. и толотом 77 кв. и толотом 78 кв. и толотом 79 кв. и толотом 80 кв. и толотом 81 кв. и толотом 82 кв. и толотом 83 кв. и толотом 84 кв. и толотом 85 кв. и толотом 86 кв. и толотом 87 кв. и толотом 88 кв. и толотом 89 кв. и толотом 90 кв. и толотом 91 кв. и толотом 92 кв. и толотом 93 кв. и толотом 94 кв. и толотом 95 кв. и толотом 96 кв. и толотом 97 кв. и толотом 98 кв. и толотом 99 кв. и толотом

11. Котем и коскидниктей та артиза, видаховод 2.000 мескидниктей, необула 2.367 мескидниктей – разкимен 4. Поставная
12. Степл ирек ветериналия (секет), 2. Номан 2016, 2. 2017 газыки лист - уким на морула- 4. Постейная застройка
13. Acute and unrecognizable use of the human space: 2000-2005. 24.
14. Use of a large object, which is clearly
15. Use of a large object in the world's space.
16. Reading the word which is writing a rule 2. High consistency of the tag > 3. A 20% maximum base - one to make a rule 4. Practice over a
17. Степл ирек ветериналия (секет), 2. Номан 2016, 2. 2017 газыки лист - уким на морула- 4. Постейная застройка
18. Acute and unenstige (e.g., 2015, 2016)
19. Reading the word which is using a rule 2. High consistency of the log > 3. A 20% maximum base - one to make the 4. Practice overpower
20. Current application of a 20% volume of water from the source.
21. 25% volume of water - 40 gm water
22. Proactive water treatment for the source.
23. Proactive water treatment for the source.
24. Proactive water treatment for the source.
25. Proactive water treatment for the source.
26. Proactive water treatment for the source.
27. Proactive water treatment for the source.
28. Proactive water treatment for the source.
29. Proactive water treatment for the source.
30. Proactive water treatment for the source.
31. Proactive water treatment for the source.
32. Proactive water treatment for the source.
33. Proactive water treatment for the source.
34. Proactive water treatment for the source.
35. Proactive water treatment for the source.
36. Proactive water treatment for the source.
37. Proactive water treatment for the source.
38. Proactive water treatment for the source.
39. Proactive water treatment for the source.
40. Proactive water treatment for the source.
41. Proactive water treatment for the source.
42. Proactive water treatment for the source.
43. Proactive water treatment for the source.
44. Proactive water treatment for the source.
45. Proactive water treatment for the source.
46. Proactive water treatment for the source.
47. Proactive water treatment for the source.
48. Proactive water treatment for the source.
49. Proactive water treatment for the source.
50. Proactive water treatment for the source.
51. Proactive water treatment for the source.
52. Proactive water treatment for the source.
53. Proactive water treatment for the source.
54. Proactive water treatment for the source.
55. Proactive water treatment for the source.
56. Proactive water treatment for the source.
57. Proactive water treatment for the source.
58. Proactive water treatment for the source.
59. Proactive water treatment for the source.
60. Proactive water treatment for the source.
61. Proactive water treatment for the source.
62. Proactive water treatment for the source.
63. Proactive water treatment for the source.
64. Proactive water treatment for the source.
65. Proactive water treatment for the source.
66. Proactive water treatment for the source.
67. Proactive water treatment for the source.
68. Proactive water treatment for the source.
69. Proactive water treatment for the source.
70. Proactive water treatment for the source.
71. Proactive water treatment for the source.
72. Proactive water treatment for the source.
73. Proactive water treatment for the source.
74. Proactive water treatment for the source.
75. Proactive water treatment for the source.
76. Proactive water treatment for the source.
77. Proactive water treatment for the source.
78. Proactive water treatment for the source.
79. Proactive water treatment for the source.
80. Proactive water treatment for the source.
81. Proactive water treatment for the source.
82. Proactive water treatment for the source.
83. Proactive water treatment for the source.
84. Proactive water treatment for the source.
85. Proactive water treatment for the source.
86. Proactive water treatment for the source.
87. Proactive water treatment for the source.
88. Proactive water treatment for the source.
89. Proactive water treatment for the source.
90. Proactive water treatment for the source.
91. Proactive water treatment for the source.
92. Proactive water treatment for the source.
93. Proactive water treatment for the source.
94. Proactive water treatment for the source.
95. Proactive water treatment for the source.
96. Proactive water treatment for the source.
97. Proactive water treatment for the source.
98. Proactive water treatment for the source.
99. Proactive water treatment for the source.
100. Proactive water treatment for the source.
101. Proactive water treatment for the source.
102. Proactive water treatment for the source.
103. Proactive water treatment for the source.
104. Proactive water treatment for the source.
105. Proactive water treatment for the source.
106. Proactive water treatment for the source.
107. Proactive water treatment for the source.
108. Proactive water treatment for the source.
109. Proactive water treatment for the source.
110. Proactive water treatment for the source.
111. Proactive water treatment for the source.
112. Proactive water treatment for the source.
113. Proactive water treatment for the source.
114. Proactive water treatment for the source.
115. Proactive water treatment for the source.
116. Proactive water treatment for the source.
117. Proactive water treatment for the source.
118. Proactive water treatment for the source.

119. Proactive water treatment

120. 2018

zelmer

WANDE THE WAN DE LAU

Flooris

ODKURZACZ

vacuum cleaner

zelmer

Exterior view of a modern vacuum cleaner (no visible text or symbols)

zelmer

golden service

s

F. INSTRUCIAL/STOCKMARK
CEKABALY (WJ) 5-8
УЗАКАС Тяс УСЛЮБ
NAYADE NA CHEN LIU
VYSAVACTYP VCT006 N-X
10. 12.47.3.15
EX WITH CUBS MUNA
ASPRATORUL Top VC1006

B. A CIPAN PRITO SECURITIES
The following table is a single data table with two columns: "Name" and "Value".
ПРАХОКУЖАЧКА ТНЯ УСТОВЫ, 5-8
UP
11MUCOC Tm VCT005 4-4
[Unreadable Text]
F

VACUUM CLEANER Type VCT006

Flooris

ODKURZACZ

vacuum cleaner

Exterior view of a modern vacuum cleaner with black handle and white base, placed on tiled floor (no text or symbols visible)

WARIANTKOLORISTYCEMY

Illustration of a vacuum cleaner with labeled parts, shown from exploded and assembled views (no text or symbols present)

Collection of industrial equipment including hoses, clamps, and a clamp (no visible text or labels)

B

E

F

G

PL

Szannawal Klendel

The following may be, and the present of the information is clearly to a guide to the words of the English. One of the words in this form is to be used to create a new, more complex, and more complex forms that are not only used to make any specific character. The words in this form are also composed of many common characters, such as "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word," "the word."

Unreal

1 Information about the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of the impact of

Dana technicana

• In addition, the company's stock price is not due to the volatility of the market. The company's stock price is 10% (as a percentage of the previous 10% of the market).

E:200000,11

Congratulations on your choice of our appliance, and welcome among the users of Zelmer products.

In order to achieve best possible results we recommend using exclusively original Zelmer accessories. They have been specially designed for this product.

Please read this instruction manual carefully. Pay special attention to important safety instructions. Keep this User's Guide for future reference.

Important safety instructions

Danger! / Warning! Health hazard

Do not operate the appliance if the cord, the housing or the handle is visibly damaged. In such a case, return the appliance to a service center.

the supply cord is damaged, it must be replaced by the manufacturer, a service agent or a qualified person in order to avoid a hazard.

The appliance can only be repaired by qualified service personnel. Improper servicing may cause a serious hazard to the user. In case of defects please contact a qualified service center.

Always unplug the appliance before cleaning, assembling or dismantling.

-urn off the device and unplug it from an outlet before replacing the equipment or approaching moving parts during use.

Do not use the vacuum cleaner to clean people or animals, pay special attention to keep the nozzles away from eyes and ears.

Do not vacuum up any liquids or wet materials.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above and supervised.

Caution!

Not observance can result in damage to possessions

Connect the vacuum cleaner only to a 230 V mains supply equipped with a 16 A fuse.

Do not unplug by pulling on cord.

Do not run the vacuum cleaner or the brushes over the cord, it may cause damage to the cord insulation.

Do not vacuum without the dust bag and the filters or if they are damaged.

Do not pick up: matches, cigarette butts, hot ash. Avoid picking up sharp objects.

Check the suction hose, the tubes and the nozzles – remove the dirt from the inside.

Do not vacuum fine dust such as: flour, cement, gypsum, toners for printers and copy machines etc.

Do not cover any of the vacuum cleaner's vent holes during operation. Heated air that cannot escape may cause the engine to overheat and become damaged or cause plastic parts to deform.

Information on the product and suggestions for its use

The vacuum cleaner is intended for domestic use only.

Operate the appliance only in indoor spaces and vacuum only dry surfaces. Before vacuuming dry the carpets that were wet cleaned.

Technical parameters

The type of the vacuum cleaner and the technical parameters are indicated on the rating label. Mains protection 16 A.

Does not cause interferences with audio/video devices.

Does not require grounding ☐

ZELMER vacuum cleaners meet the requirements of the applicable norms.

The appliance is in conformity with the requirements of the directives:

Low voltage appliance (LVD) - 2006/95/EC.

– Electromagnetic compatibility (EMC) – 2004/108/EC.

Noise level: max. 78 dB/A

The appliance was marked by a CE sign on the rating label.

Static electricity

In the process of vacuuming of some surfaces in areas of low air humidity the device may become electrically charged. It is a natural phenomenon – it does not damage the device, and it is not considered to be a fault.

In order to minimize the phenomenon, we recommend you to:

discharge the device by touching metal items in the room with the pipe,

Increase air humidity in the room,

- se widely available antistatic agents.

Type\Workmanship and equipment option

Suction power regulator

Overheating protection

Safety valve

Parksystem „Auto-start"

Bag loading indicator

No bag protection

Dust bag / amount

Outlet filter

Suction tube

Combination brush

Small nozzle

Crevice nozzle

Small brush

Turbo brush

Parquet brush “BNB”

1

2

4

5

6

7

8

9

10

11

12

13

14

15

16

17

VC1006.0HP

+

+

+

+

+

+

SAFBAG 2 pieces

HEPA H13

Telescopic

+

+

+

+

-

+

VC1006.0ST

+

+

+

+

+

+

SAFBAG 2 pieces

HEPA H11

Telescopic

+

+

+

+

+

-

VC1006.0HT

+

+

+

+

+

+

SAFBAG 2 pieces

HEPA H13

Telescopic

+

+

+

+

+

+

Appliance elements

1 Cord rewind button
2 Combination brush fastening
3 Plug and cord
4 Filter cover release button
5 Outlet filter cover
6 Suction power regulation slider
7 Dust bag full indicator
8 ON/OFF button
9 Handle
10 Front cover fastening
11 Slider – mechanical suction power regulator
12 Suction hose
13 Telescopic suction tube
14 SAFBAG dust bag
15 SAFBAG dust bag module (with the installed SAFBAG dust bag)
16 Outlet filter. The vacuum cleaner is fitted with only one outlet filter (A or B)

A HEPA H11 outlet filter (only in model VC1006.0ST) (installed in the vacuum cleaner)

B HEPA H13 outlet filter (only in models VC1006.0HT and VC1006.0HP) (installed in the vacuum cleaner)

17 Inlet filter casing (installed in the vacuum cleaner)
18 Inlet filter (installed in the vacuum cleaner)
19 Parquet brush "BNB" (Brush Natural Bristle) (only in models VC1006.0HT and VC1006.0HP)

Is used to clean and polish hard, scratch sensitive surfaces such as wooden floors, floor panels, parquet, marble, tiles, etc.

Delicate and soft natural bristles ensure maximum vacuum effectiveness and protects against scratching the cleaned surface.

20 Small nozzle
21 Small brush
22 Crevice nozzle
23 Switchable combination brush
24 Turbobrush (only in models VC1006.0HT and VC1006.0ST)
25 Accessory holder
26 Holder screws

Preparing the vacuum cleaner for operation

① Insert the curved hose end in the opening of the vacuum cleaner and gently press. A characteristic click indicates that the hose has been properly installed.
② Connect the other end of the hose (handle) with the telescopic suction tube. In order to do so press the locking device “A” and slide the tube into the hose handle so that the locking device “A” is blocked in opening “B”.
③ Adjust the length of the telescopic suction tube by sliding the slider according to the arrow and pull out/ pull the tube together.
④ Assemble the appropriate nozzle or brush to the other end of the suction tube.
⑤ To clean hard surfaces – wooden floors, plastic floors, ceramic tiles etc. pull out the brush by pressing the switch on the combination brush according to the figure
⑥ The accessories may be attached to the accessory holder in the suction hose handle. This way they will be available for use at any time.

⑦ Pull the plug and cord (3) out of the vacuum cleaner. Do it smoothly (do not tug) to avoid cord tangling and blocking in the vacuum body.

puling out the cord pay attention to the yellow stripe which signals the end of the cord. Further attempts (pulling on cord) may result in damaging the cord.

⑧ Plug in the appliance.

Before operation make sure that the SAFBAG bag is installed in the vacuum cleaner chamber and that inlet filter and the HEPA outlet filter is installed in the appliance.

⑨ Switch on the vacuum cleaner by pressing the "on/off" button (8).
⑩ The vacuum cleaner is equipped with electronic power regulator allowing a stepless regulation of vacuum cleaner power. The power regulation is performed with a slider.

Moving the slider right or left will increase or reduce the suction power.

The following slider positions are recommended:

– for delicate fabrics such as curtains, etc.

– for upholstered furniture

– for carpets and floor coverings

- for hard surfaces such as floor, tiles, parquet etc.

The power may also be adjusted individually depending on the type of surface, vacuum effectiveness and suction power of the switchable combination brush.

⑪ The vacuum cleaner is equipped with the "Parksystem Auto-Start" function (available only in models VC1006.0HT, VC1006.0ST and VC1006.0HP). It allows to switch the appliance for a short time using the fastening hook of the combination brush, without having to use the on/off button. To do so, while the vacuum cleaner is in operation insert the fastening hook of the combination brush to the combination brush fastener (2) (the vacuum cleaner must be in a horizontal position). The vacuum cleaner will be switched off automatically.
⑫ The vacuum cleaner is also equipped with a mechanical suction power regulator (11) located on the suction hose handle. It can be used to adjust the suction power slightly for a short time without having to use the slider (6).

Filter disassembly

Before changing the filters make sure that the vacuum cleaner is switched off and unplugged from the mains supply.

INLET FILTER

① Release the catch of front cover (10) and open it.
② Remove the SAFBAG dust bag module from the vacuum cleaner chamber.

③ Put out the cover of inlet filter together with installed inlet filter from the guide rails located on back wall of vacuum cleaner chamber.
④ Take out the inlet filter from the inlet filter cover.
⑤ Put the new filter into inlet filter cover (17). Pay attention whether the edges of filter cling closely to the cover of filter.
⑥ The cover of inlet filter (17) together with installed filter press home into guide rails to the previous location.

damaged inlet filter should be replaced with a new, genuine manufactured product only.

⑦ Insert the SAFBAG dust bag module to the vacuum cleaner chamber.
⑧ Close the cover by pressing it until you hear a characteristic click – pay attention not to trap the dust bag.

HEPA OUTLET FILTER

The vacuum cleaners are equipped with a H11/H13 class HEPA outlet filters.

HEPA filters are high-quality filters produced from special fibres which are able to stop almost all dust particles. The H11/H13 class indicates the permeability of the filter. The H11 HEPA filter stops 95% of particles as small as 0.3 micron, and the H13 HEPA filter stops as much as 99.95% of all impurities.

① In order to replace the HEPA filter, press the blocking mechanism of the outlet filter cover and slide up the cover of the vacuum cleaner.
② Remove the HEPA filter cassette and replace it with a new one. The HEPA filter assures circa 1 year of effective usage.
③ Slide the outlet filter cover back on in such a way that the fastenings on the side of the cover fit into the sliders in the vacuum cleaner housing. The filter cover fastening should close.

SAFBAG dust bag disassembly/assembly

① The vacuum cleaner is equipped with safety valve located in chamber of dust container (bag). It opens automatically in case of total stopping of suction hose or total stopping of equipment elements connected thereto, as well as in case of overfill of dust bag. After opening the valve one can hear characteristic "whirr" sound inside the vacuum cleaner.
② When the “Dust bag full” indicator light (7) comes on when the nozzle or brush is above the floor, it indicates that the bag needs to be replaced. The “Dust bag full” indicator light may come on when the suction hose or connected accessories become clogged.
③ Switch off the vacuum cleaner by pressing the on/off button (8) and unplug the appliance.
④ Press the two side buttons on the end of the hose and remove the hose end from the inlet opening of the vacuum cleaner.

⑤ Release the front cover fastening (10) and open the cover.
⑥ Remove the SAFBAG dust bag module from the vacuum cleaner chamber (15).
⑦ While holding the module, pull the frontal part of the bag plate upwards and remove the bag. Close the SAFBAG bag cap to close the full bag. Dispose of the bag.
⑧ Slide the plate of the new bag in the direction shown in the picture. The end of the plate should lock in the socket. The bag cap should be on top. The direction is shown by an arrow placed on the bag.

But the SAFBAG module together with the assembled bag (15) into the vacuum cleaner container so that the cogs of the SAFBAG module fit into the holes in the container wall. Press and close the cover until you hear the characteristic clicking sound – be careful not to catch the bag.

not vacuum without SAFBAG bag module installed. The lack of SAFBAG bag disables to slam the upper cover cleaner.

ZELMER vacuum cleaners are equipped with SAFBAG dust bags in the amount indicated in the table. It is recommended to replace the dust bag if:

a) the "Dust bag full" indicator light will come on,
b) the safety valve activates,
c) the vacuum cleaner operates poorly,
d) the dust bag is full.

Accessory holder

The accessory holder allows hanging accessories (suction tube, small nozzle, small brush, crevice nozzle, combination brush, turbobrush or parquet brush) for example in the closet.

① Join the holder elements.
② Screw the holder (for example to the wall of the closet) using the four provided screws.
③ Fit the accessories onto the holder as shown in the picture.

Overheating protection

Models VC1006.0HT, VC1006.0ST and VC1006.0HP have an overheating protection device. If will automatically switch off power to the motor if it overheats. If this happens, turn off the vacuum by pressing the ON/OFF button (8). Allow the vacuum cleaner to cool for approx. 40 min. and switch it on again. If the vacuum cleaner does not start, return it to an authorised service agent for repair.

Special accessories

The following special accessories may be purchased in retail outlets:

Parquet brush "BNB" (19)

The parquet brush is used to clean and polish hard, scratch sensitive surfaces such as wooden floors, floor panels, parquet, marble, tiles, etc.

Delicate and soft natural bristles ensure maximum vacuum effectiveness and protects against scratching the cleaned surface.

Zelmer turbobrush (24)

May be used with all types of ZELMER vacuum cleaners. Is used for an effective vacuuming of carpets and fitted carpets. While using the turbobrush follow the instruction manual.

The use of the turbobrush decidedly increases the effectiveness of removing fibrous dirt such as: animal hair, maitulereads etc. It is practically useful in households with of pets (cued dogs), where removing the animal hair from the carpets and floorings is very onerous.

End of operation cleaning and maintenance

① Switch off the vacuum cleaner by pressing the "on/off" button (8).
② Unplug the appliance.
③ Wind the cord by pressing the cord rewind button (1). While doing this hold the cord to make sure it is not tangled and the plug does not hit the vacuum cleaner housing.
④ Disconnect the telescopic tube from the nozzle or brush.
⑤ Disconnect the telescopic tube from the hose. In order to remove the tube from the hose handle press the "A" locking device and pull the tube in the direction of the arrow.
⑥ Press the two side buttons on the end of the hose and remove the hose end from the inlet opening of the vacuum cleaner.
⑦ The vacuum cleaner may be stored vertically or horizontally. In order to do so, insert the fastening hook of the combination brush to the combination brush fastener. The hose may be attached to the vacuum cleaner, however you have to make sure that it is not excessively bent during storing.
⑧ If necessary wipe the housing and the dust bag container with a damp cloth (it may be soaked with dishwashing liquid) and dry it or wipe until dry.

Do not use abrasive detergents or solvents.