Q: How to change the drying level in the Mixed program?

Yes, the Mixed program of your AEG EDH3497RDW tumble dryer allows you to change the drying level. This option is called Dryness (or 'End Dryness Moisture') and lets you adjust the result according to your needs. How to change the drying level: Select the Mixed program by turning the program knob Press the Dryness touchpad (marked with a + and X symbol) located to the right of the control panel Each press increases the drying level; the levels cycle in the following order: Extra Dry, Cupboard Dry, Iron Dry The display shows the selected level Press Start/Pause to begin the cycle Available drying levels for Mixed: Extra Dry : for very dry drying, ideal before long-term storage Cupboard Dry : standard norm, laundry ready to be stored immediately Iron Dry : slightly damp laundry, easier to iron Important: The 'Strong Dry' level (intensive drying) is not available for the Mixed program; it is reserved for the Cotton program. For the Mixed program (which handles cotton and synthetics at low temperature), the three levels above are sufficient and optimize drying without risking damage to synthetic fibers.

Question 1

How to adjust the energy limit of the cooking hob?

Accepted Answer

To adjust the energy limit of your AEG-ELECTROLUX EHI8742F9K, follow these steps:

Turn off the device
Press the button ① for 3 seconds - the display lights up and then turns off
Press the button ① again for 3 seconds - "or" is displayed
Press the button ① - "P0" is displayed (maximum level: 7200 W)
Use the - / + timer buttons to decrease or increase the power level

Available power levels:

P0: 7200 W (maximum)
P1: 1500 W
P2: 2000 W
P3: 2500 W
P4: 3000 W
P5: 3500 W
P6: 4000 W
P7: 4500 W
P8: 5000 W
P9: 6000 W

Tip: Ensure that the selected power level matches your electrical installation.

Question 2

How to make a rolled hem with the AEG-ELECTROLUX 90S?

Accepted Answer

Rolled hem on the AEG-ELECTROLUX 90S

The rolled hem is an elegant finish that creates a perfect rolled edge on lightweight fabrics. Here’s how to achieve it with your overlock machine.

Preparing the machine

Remove the left needle to switch to 3-thread configuration
Install the special presser foot provided with your machine
Set the stitch length between 1.0 and 2.0 mm
Adjust the stitch width according to the type of fabric

Preparing the threads

Needle thread: Polyester silk No. 50-80
Upper looper: Foam thread for a perfect finish
Lower looper: Polyester silk No. 50-80

Execution

Position the finger of the special presser foot forward for the rolled hem mode
First, test on a scrap piece of fabric
Place the edge of your fabric under the presser foot
Start sewing - the loops of the lower looper should wrap under the fabric to create the hem
Remember to return the presser foot to normal position after use

Tip: This technique works particularly well on lightweight fabrics like chiffon or silk. Always test on scraps before starting on your final piece.

Question 3

How to replace the lamp of the X56143MDO hood?

Accepted Answer

To replace the lamp of your AEG-ELECTROLUX X56143MDO hood, follow these important steps:

Preparation and safety: Before any intervention, unplug the hood from the power supply by removing the plug or turning off the main switch. This precaution is essential to avoid any electrical risk when replacing the bulb.

Accessing the bulb: Locate the tray or diffuser located under the hood (usually a removable part that slightly protrudes). Carefully remove it by pulling it down or unscrewing it depending on the model. This action will allow you to access the lighting bulb.

Identification and replacement: Once the diffuser is removed, you will see the halogen or LED bulb depending on your version. Note precisely the type and power (voltage and wattage) indicated on the bulb itself. Replace it with an identical bulb in type and power. Using a non-compliant bulb could damage the electrical system of the hood or reduce the lighting efficiency.

Correct handling: When replacing, wear cotton or cleaning gloves to prevent grease or moisture from your hands from transferring onto the new bulb. These residues can significantly reduce the lifespan of the bulb and alter its brightness. Once the bulb is installed, replace the diffuser by securing it properly.

Final check: Plug the hood back into the power supply and test the lighting by pressing the L (Light) button located on the control panel. The lighting should turn on and off correctly.

If you cannot find the exact compatible bulb type or if the replacement does not work as expected, contact AEG-ELECTROLUX customer service with the serial number of your hood (visible on the inner nameplate) and the model number X56143MDO. They will be able to provide you with the precise references for the original spare parts.

Question 4

Why are only the Delay and Anti-crease options available?

Accepted Answer

This depends on the selected program. On this AEG EDH3497RDW tumble dryer, not all options are available on all programs.

For example, if you are on the Mixed program, only the Delay Start and Anti-crease options are available. This program does not support the dryness adjustment.

To access the dryness option, you need to switch to another program that supports it, such as:

Cottons (supports 4 levels: Extra Dry, Strong Dry, Cupboard Dry, Iron Dry)
Synthetic
Jeans

These programs offer four dryness settings to tailor the result to your drying preference.

Question 5

How to change the drying level in the Mixed program?

Accepted Answer

Yes, the Mixed program of your AEG EDH3497RDW tumble dryer allows you to change the drying level. This option is called Dryness (or 'End Dryness Moisture') and lets you adjust the result according to your needs.

How to change the drying level:

Select the Mixed program by turning the program knob
Press the Dryness touchpad (marked with a + and X symbol) located to the right of the control panel
Each press increases the drying level; the levels cycle in the following order: Extra Dry, Cupboard Dry, Iron Dry
The display shows the selected level
Press Start/Pause to begin the cycle

Available drying levels for Mixed:

Extra Dry: for very dry drying, ideal before long-term storage
Cupboard Dry: standard norm, laundry ready to be stored immediately
Iron Dry: slightly damp laundry, easier to iron

Important: The 'Strong Dry' level (intensive drying) is not available for the Mixed program; it is reserved for the Cotton program. For the Mixed program (which handles cotton and synthetics at low temperature), the three levels above are sufficient and optimize drying without risking damage to synthetic fibers.

Question 6

How to assemble and install the AEG-ELECTROLUX DPB3931M kitchen hood?

Accepted Answer

Assembly of the AEG-ELECTROLUX DPB3931M hood

The installation is done in several essential steps. Start by checking that you have all the provided accessories: the hood, mounting screws, the specific installation guide, filters, and the necessary tools (drill, bit, level, screwdriver, work gloves).

Positioning and height: Install the hood directly above your cooking surface. Maintain a minimum distance of 65 cm between the support surface of the containers and the lowest part of the hood for gas or mixed cookers, and 43 cm for electric cookers. The hood has an adjustable height of 70 to 100 cm to fit your kitchen.

Marking and drilling: Use the drilling template provided with the hood. Draw a horizontal line using the level, then mark the drilling points. Drill the holes by selecting an appropriate bit according to your wall type (plaster, concrete, brick). Use only the mounting screws provided in the installation kit.

Electrical connection: Before any electrical work, turn off the main power supply to your home. The hood operates at 230 V, 50 Hz. Follow the instructions in the installation guide for the connection: if a plug is provided, connect it to an accessible wall socket that complies with standards. If the connection is direct to the electrical circuit, install a standardized circuit breaker ensuring complete disconnection.

Filter installation: Before putting the hood into operation, install the filters. The grease filter (washable metallic) should be cleaned monthly by hand or in the dishwasher at low temperature. The activated carbon filter (non-washable) should be replaced every 4 months maximum depending on usage frequency and regular cleaning of the grease filter.

Final check: Once the electrical installation is complete, turn on the hood and test the different suction speeds to check its proper functioning. Ensure that the horizontal alignment is respected with the level. Important: never connect the device to the electrical network before the installation is completely finished. For doubts or installation issues, consult an authorized technical service or qualified personnel.

User manual AEG-ELECTROLUX : user manuals and guides in PDF

Models AEG-ELECTROLUX most viewed

Browse manuals AEG-ELECTROLUX by appliance type

Recent questions about devices AEG-ELECTROLUX