ZUIKO DIGITAL ED 300MM F2.8 - Objectif photo OLYMPUS - Notice d'utilisation et mode d'emploi gratuit

Type d'appareil	Objectif photo
Marque	Non précisé
Modèle	Non précisé
Focale	300 mm
Ouverture maximale	f/2.8
Monture	Non précisé
Type d'objectif	Téléobjectif
Stabilisation d'image	Non précisé
Distance minimale de mise au point	Non précisé
Poids	Non précisé
Dimensions	Non précisé
Compatibilité	Appareils photo numériques
Type de mise au point	Automatique et manuelle
Construction optique	Non précisé
Accessoires inclus	Non précisé

FOIRE AUX QUESTIONS - ZUIKO DIGITAL ED 300MM F2.8 OLYMPUS

Comment puis-je nettoyer l'objectif OLYMPUS ZUIKO DIGITAL ED 300MM F2.8 ?

Utilisez un souffleur pour enlever la poussière, puis un chiffon en microfibre légèrement humide pour nettoyer les lentilles. Évitez d'utiliser des produits chimiques agressifs.

Pourquoi mon objectif ne fait-il pas la mise au point correctement ?

Vérifiez que l'objectif est bien fixé au boîtier de l'appareil photo. Assurez-vous également que le mode autofocus est activé et que vous utilisez un objectif compatible.

L'objectif est-il compatible avec mon appareil photo OLYMPUS ?

L'OLYMPUS ZUIKO DIGITAL ED 300MM F2.8 est compatible avec les appareils photo OLYMPUS utilisant la monture 4/3. Vérifiez les spécifications de votre appareil pour confirmer.

Comment puis-je éviter le flou de mouvement lors des prises de vue avec cet objectif ?

Utilisez une vitesse d'obturation rapide pour compenser le flou de mouvement. Un trépied ou un monopode peut également aider à stabiliser l'appareil.

Quel type de filtre puis-je utiliser avec l'objectif ?

Vous pouvez utiliser des filtres de 77 mm de diamètre. Assurez-vous que le filtre est conçu pour un objectif téléobjectif pour éviter la dégradation de la qualité d'image.

L'objectif est-il étanche ou résistant aux intempéries ?

L'OLYMPUS ZUIKO DIGITAL ED 300MM F2.8 est conçu pour être résistant aux intempéries, mais il est conseillé d'éviter une exposition prolongée à des conditions extrêmes.

Que faire si l'objectif ne s'ouvre pas correctement ?

Assurez-vous que l'objectif est correctement monté sur le boîtier. Si le problème persiste, contactez le service client OLYMPUS pour une assistance technique.

Comment puis-je obtenir des mises à jour du firmware pour l'objectif ?

Vérifiez le site officiel d'OLYMPUS pour les mises à jour de firmware. Suivez les instructions fournies pour mettre à jour votre objectif si nécessaire.

MODE D'EMPLOI ZUIKO DIGITAL ED 300MM F2.8 OLYMPUS

OLYMPUS

ZUIKO DIGITAL

ED300mm f2.8

Instructions

For customers in Europe

The "CE" mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. CE-mark products are for sale in Europe.

For customers in USA

FCC Notice

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any unauthorized changes or modifications to this equipment would void the user's authority to operate.

For customers in CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Features

• The ED300mm f2.8 is a lens with high imaging capability, designed exclusively for use with Olympus FOUR THIRDS single-lens-reflex digital cameras.
• Dustproof and drip-proof construction.
• Super-telephoto lens corresponding to a 600mm lens for a 35mm camera.
• F2.8 high-quality lens with 13 elements in 11 groups including three ED (extra-low dispersion) glass elements.
• Can be used in combination with the optional EC-14 teleconverter.
• Can be used in combination with the optional EX-25 extension tube for low-magnification shooting (between 0.08X and 0.25X).

Contents

• Checking the Package Contents 13
  Nomenclature 14
• Attaching the Lens Strap 14
• Attaching the Lens Case Strap 14
• Attaching the Lens Hood LH-120 15
  · Filters 15
• Mounting a Filter 16
  Focus Limit Switch 17
  Focus Stop Buttons 17
• Shooting Cautions 17
• Attaching the Lens Cap LC-140 17
• Precautions: Be Sure to Read the Following 18
  ·Main Specifications 19

Checking the Package Contents

Lens body

Lens Hood LH-120

Lens Case LSH-1738

Drop-In Filter Holder DFH-43/

Standard Clear Filter SCF-43

(Mounted on the lens body at the factory)

Filters (ND4-43, ND8-43)

Drop-In Circular PL Filter DPF-43

Filter Case FSC-1

Lens Cap LC-140

Lens strap

Nomenclature

① Focus stop buttons (x4)
②Drop-in filter
③Mounting index
④Rear cap
⑤Strap attachment
⑥ Focus limit switch
⑦Focus ring
⑧Filter mount thread
Hood attaching section
10Electrical contacts
⑪ Tripod mount

Attaching the Lens Strap

Attaching the Lens Case Strap

Attaching the Lens Hood LH-120

• Before mounting the lens hood on the lens or before storing them, loosen the mounting screw until it stops.

After putting the hood on the lens as shown, fit the claw inside the lens hood securely into the grooves in the hood mounting section and then tighten the mounting screw.

Filters

The lens comes with the following filters.

① Standard clear filter SCF-43 .... Always mount this filter when not using any of the other filters.

②ND4-43 Decreases the amount of light entering the lens by 1/4.

③ND8-43 Decreases the amount of light entering the lens by 1/8.

④ Drop-in PL filter DPF-43

This filter eliminates surface reflected light.

The amount of reflected light eliminated can be adjusted with a rotary lever.

Mounting a Filter

1. ND4-43/ND8-43

① Remove the SCF-43 clear filter from the filter holder and attach the ND4-43 or ND8-43 to the filter holder.
- The DPF-43 drop-in PL filter should not be used with the filter holder.
② Insert the filter holder in the lens's mounting section.

③ Firmly push the filter holder in until it clicks.
- After mounting the filter holder, make sure that it does not come off.

Notes:

If the filter holder is improperly mounted, it may come off. In this case, the unit's dust and drip resistance may be compromised.

④ When detaching the filter holder, push and hold the detach button and pull out the filter holder.

2. Drop-in PL filter DPF-43

① Attach the DPF-43 drop-in PL filter to the lens body so that the is pointing to the front.

② Rotate the rotary lever to adjust the level of surface reflection elimination.

Focus Limit Switch

This switch limits the autofocus range to speed up focusing in each range.

Select the optimum mode according to the shooting distance.

• Close-up shooting : Autofocus is performed between 6 meters and 2.4 meters.

Normal shooting : Autofocus is performed from (infinity) to 2.4 meters.

Distant shooting : Autofocus is performed from (infinity) to 6 meters.

Focus Stop Buttons

• By holding down one of the focus stop buttons, you can deactivate autofocus operation and fix focus at the point where the button was pressed.
• Four buttons are provided. All have the same effect.

Shooting Cautions

• Be sure to attach the hood when shooting against the light.
• When two or more filters are used or a thick filter is used, part of the picture may be cut off or obscured.

Attaching the Lens Cap LC-140

Precautions: Be Sure to Read the Following

Warnings: Safety Precautions

Do not view the sun through the lens.

Do not leave the lens without the cap. If solar light is converged through the lens, a fire may result.

Do not point the camera lens at the sun. Sunlight will converge in the lens and focus inside the camera, possibly causing a malfunction or fire.

Handling Precautions

Working temperature range

Abrupt temperature changes

Do not put the lens with its contacts facing down.

Too much pressure

Do not touch the lens.

Submergence

Do not touch the contacts.

Do not drop

Organic solvents

Excessive moisture

Magnetism

Do not hold the camera by the section of the lens extruded by the focusing operation.

Storage Precautions

Cap the lens when it is not used.

Lens cleaning

Moth repellents

If you experience any problems, contact your nearest Olympus service center.

Main Specifications

Mount : Four Thirds mount

Focal distance : 300 mm

Max.aperture :f2.8

Image angle : 4.2^

Lens configuration : 13 elements in 11 groups Multi-layer coating (partial single-layer coating)

Iris control :f2.8 to f22

Shooting range : 2.4 m to (infinity)

Focus adjustment : AF/MF switching

Weight : 3290 g (excluding hood and cap)

Dimensions : Max. dia. 127× Overall length 285mm

Lens hood mount : Covering

Filter mount thread diameter : 112 mm

• Design and specifications are subject to change without any notice or obligation on the part of the manufacturer.

Lens configuration diagram

Technical Support (USA)

24/7 online automated help: http://www.olympusamerica.com/E1

Phone customer : Tel.[phone] (Toll-free)

Our phone customer support is available from 8 am to

10 pm (Monday to Friday) ET

E-Mail: [e-mail]

European technical Customer Support

Please visit our homepage http://www.olympus-europa.com

or call NUMBER: Tel.[phone] (Toll-free)

[phone] or [phone] (Charged)