User manual CLATRONIC Air conditioner : 4 free PDF user manuals

Q: How to change the temperature unit to Celsius on the CLATRONIC CL 3716?

The CLATRONIC CL 3716 air conditioner operates exclusively in Celsius - there is no option or menu to change the temperature unit to Fahrenheit. According to the technical manual, the device always displays temperatures in degrees Celsius. The available settings range from 16 °C to 31 °C in cooling mode, and you can adjust the temperature using the +/- buttons on the control panel or the remote control. The device is pre-programmed to 22 °C in cooling mode by default. No setting in the menu or adjustments allows switching to another temperature unit. If you need to convert to Fahrenheit for reference, you can use the formula: °F = (°C × 9/5) + 32

Q: Does the CLATRONIC CL 3716 air conditioner produce cold intermittently, is this normal?

Yes, this is a completely normal operation. The compressor of the CLATRONIC CL 3716 does not run continuously, but in regulated automatic cycles: Regulated cooling cycle Once the room reaches the temperature you have set (between 16 and 31 °C), the compressor automatically stops. When the temperature rises, it restarts. This is exactly the same principle as a heating thermostat - the compressor needs to take breaks to maintain the ambient temperature. This intermittence is normal and desirable : it prevents overcooling and reduces electricity consumption (the CLATRONIC CL 3716 is energy rated A). Automatic compressor shutdown to empty the tank When the condensation water tank is full (with the FL indicator lit), the compressor automatically stops, even if the temperature has not been reached. Only the fan continues to operate. You then need to empty the water tank at the back of the unit by removing the cap and using the provided hose. Technical note: After a shutdown, the compressor waits about 3 minutes before restarting to allow the refrigerant circuit (R290) to depressurize properly. Optimizing performance Clean the filters every 2 weeks with daily use (vacuuming or washing with lukewarm water) - do not let the unit operate without filters Close doors and windows to maintain cooling Set the temperature to a value lower than that of the room Ensure to use the unit in a room of at least 12 m²

Q: Through which outlet(s) do the condensates flow from the CLATRONIC CL 3716?

The condensates flow through two outlets located at the back of the unit (marked as items 9 and 12 in the technical documentation). Drainage procedure: Unplug the device from the wall socket Place one or more containers under the rear drainage outlets Remove the caps from the two drainage points Connect the supplied flexible hose to direct the water to a basin or drainage system Replace the caps after draining Fill indicator: The "FL" indicator lights up when the tank is full. At this point, the compressor stops automatically (only the fan continues to operate), preventing any overflow. Warning: Never move the device when the tank is full, as water could seep into the internal components.

Q: Where is the water tank of the CLATRONIC CL 3716 located?

The water tank of the CLATRONIC CL 3716 is located inside the condensation unit of the appliance. This tank collects the condensation water generated during operation in cooling or dehumidification mode. You can drain this tank through two water outlets located at the back of the unit (items 9 and 12 in the diagram). When the tank fills up, the “FL” indicator lights up on the screen to signal that draining is necessary. At this point, the compressor automatically turns off, but the fan continues to operate. To empty the tank: First, unplug the appliance from the wall socket Place a mop and a basin with a capacity of about 1 liter under the water outlet at the back If possible, position the basin at a lower level than the appliance to facilitate drainage Remove the cap from the water outlet Connect the water hose supplied with the appliance to the outlet to drain the water cleanly into the basin Once empty, replace the cap and plug the appliance back in Important: Never move the appliance when the tank is full, as water could seep inside and damage the internal components. Always drain the tank before moving the air conditioner.

Models CLATRONIC Air conditioner most viewed

★★★★★

★★★★★

★★★★★

★★★★★

Other categories CLATRONIC

Kitchen appliance 73 Vacuum Cleaner 70 Coffee machine 59 Kettle 58 Iron 56 Food Processor 47 Microwave 44 Deep fryer 34 Fondue, raclette and wok appliance 33 Toaster 22 Electric heater 21 Mixer 21 CD Player 19 Cooker 16 Hair dryer 16 Blender 15 Oven 15 Hi-fi system 15

See all categories CLATRONIC (105) → ← All manuals CLATRONIC

Recent questions about Air conditioner CLATRONIC

🕐 27/06/2026

How to change the temperature unit to Celsius on the CLATRONIC CL 3716? CLATRONIC CL 3716

🕐 24/06/2026

Does the CLATRONIC CL 3716 air conditioner produce cold intermittently, is this normal? CLATRONIC CL 3716

🕐 29/05/2026

Through which outlet(s) do the condensates flow from the CLATRONIC CL 3716? CLATRONIC CL 3716

🕐 29/05/2026

Where is the water tank of the CLATRONIC CL 3716 located? CLATRONIC CL 3716

User manual CLATRONIC Air conditioner : user manuals and guides in PDF

Models CLATRONIC Air conditioner most viewed

Other categories CLATRONIC

Recent questions about Air conditioner CLATRONIC