Q: How to make ice with this refrigerator?

Your LG GR-P257SVK refrigerator has a built-in ice maker that automatically produces ice cubes. Here’s how to use it: Prerequisites The appliance must be properly connected to a water supply with adequate pressure The ice maker must be turned on (check that the switch is not in the off position) The freezer temperature must be set to 0°F (-18°C) or lower Operation Once activated, the ice maker automatically produces ice cubes and stores them in the bin. You can retrieve them directly through the dispenser built into the refrigerator door. If no ice is produced Check that the ice bin is not frozen or blocked Ensure that the water supply line is not frozen or clogged Turn the ice maker off and then back on Wait 12 to 24 hours for the first ice production to begin

Q: Why is my refrigerator not cold enough while the compressor is running?

Observed symptom: The refrigerator's compressor is functioning normally, but the appliance is not cooling sufficiently. You notice that the back of the appliance is not as warm as it should be. This symptom may indicate a problem with the circulation of the refrigerant (cooling gas) rather than an issue with the compressor itself. Before concluding that the compressor is faulty, check the following: Checks to perform: Clean the rear ventilation grilles: Dirt or blockage at the condenser (rear coil) prevents proper heat dissipation. Unplug the appliance, wait 30 minutes, then carefully clean the rear grille. Check air circulation: Ensure that no food or packaging is obstructing the internal ventilation openings. Cold air must circulate freely in all compartments. Check temperature settings: Make sure the thermostat is not set too high. An incorrect setting can cause the compressor to run without effective cooling. Inspect door seals: Worn or poorly closed seals allow cold air to escape and force the compressor to work harder without results. If the problem persists: After these checks, if the back of the refrigerator remains cold and the appliance still does not cool, it is likely that there is a refrigerant leak or a malfunction of the temperature sensor. These issues require professional technical intervention, as they involve the hermetic circuit of the appliance.

Q: How to turn on and set up the LG GBB71NSDFN refrigerator?

Powering On: After installation, plug the power cord into an outlet (220-240 V, 50 Hz). Then wait 2 to 3 hours before using the appliance to allow the cooling to stabilize completely. Temperature Settings: Refrigerator: Press the Fridge Temperature button to adjust the temperature between 1°C and 7°C (default temperature: 3°C). Freezer: Press the Freezer Temperature button to adjust the temperature between -15°C and -23°C (default temperature: -18°C). Additional Features: Express Cool : For quick cooling, hold the button for 3 seconds. Express Freeze : For quick freezing, hold the button for 3 seconds. Eco Friendly : Activates energy-saving mode. Wi-Fi : Connect the appliance via 2.4 GHz to the LG ThinQ app for remote control. Lock : Hold for 3 seconds to lock all buttons and prevent accidental changes.

Question 1

How to access and remove the back panel of the freezer?

Accepted Answer

The manual for the LG GML844PZ6F does not contain specific instructions for removing the back panel of the freezer. This panel is generally not designed to be removed by the user themselves.

If you wish to clean the condenser (located at the back), the manual recommends: use a vacuum cleaner with a brush to clean the condenser cover. This operation does not require removing the entire back panel.

For a deeper intervention on the internal components (compressor, refrigeration circuits, etc.), we recommend contacting an authorized LG technician or LG customer service. Accessing the back panel without the proper knowledge could damage the cooling system or void the warranty.

Can you specify what you are looking to achieve or clean? This would allow us to offer you a suitable solution.

Question 2

Water is leaking from the bottom of the door near the hinge

Accepted Answer

Water leaks at the bottom of the door of the GC-P197WFS refrigerator, particularly near the hinge, are generally caused by one of the following issues:

Most Likely Causes

Clogged drainage channel - The GC-P197WFS refrigerator has a drainage system for condensation water. If the drainage channels (usually located at the back or underneath the appliance) are blocked by debris or limescale, water accumulates and leaks out through unexpected openings like the bottom of the door.
Damaged or misaligned door seal - Warm air easily enters, creating excessive condensation. Check that the rubber seal around the door is clean, free of cracks, and properly pressed against the frame.
Damaged door plumbing - The GC-P197WFS model has water plumbing in the door area (for ice or cold water dispensers). A crack, wear, or poor fitting can cause a leak at this point.

Solutions to Try

Clean the door seal with a damp cloth and mild soap, then dry it thoroughly.
Check that the door closes properly and that the seal adheres well along its entire length.
Inspect the back of the refrigerator to locate and clean the drainage openings.
Check the visible water pipes in the door area for leaks, cracks, or loose plumbing.
Ensure that the refrigerator is level (slightly tilted backward) so that water drains properly.

If after these checks the leak persists, contact an authorized LG service technician to replace the damaged plumbing or seal.

Question 3

How to make ice with this refrigerator?

Accepted Answer

Your LG GR-P257SVK refrigerator has a built-in ice maker that automatically produces ice cubes. Here’s how to use it:

Prerequisites

The appliance must be properly connected to a water supply with adequate pressure
The ice maker must be turned on (check that the switch is not in the off position)
The freezer temperature must be set to 0°F (-18°C) or lower

Operation

Once activated, the ice maker automatically produces ice cubes and stores them in the bin. You can retrieve them directly through the dispenser built into the refrigerator door.

If no ice is produced

Check that the ice bin is not frozen or blocked
Ensure that the water supply line is not frozen or clogged
Turn the ice maker off and then back on
Wait 12 to 24 hours for the first ice production to begin

Question 4

How to lower the temperature of the LG GR-S652QUQA refrigerator?

Accepted Answer

To lower the temperature of your LG GR-S652QUQA refrigerator, you have two methods depending on the zone:

Refrigerator

Press the REF TEMP button to set the temperature to 5 different levels. Move the selection to MAX to make the fridge colder (lower temperature).

Freezer

Turn the graduated knob from 1 to 7 located on the control panel. The higher the number, the lower the temperature will be. The default setting is 3.

Note: Both compartments share cold air. If you set the freezer to a lower temperature, the refrigerator will automatically become a little less cold. You can refer to the full manual for more details on these operations.

Question 5

What should I do if my LG GBP62MCNBC refrigerator is not cooling and all the LEDs are on?

Accepted Answer

This symptom (all LEDs on + no cooling) often indicates a temperature alarm on your LG GBP62MCNBC. Here’s how to diagnose and resolve:

Diagnostic Steps:

Check that the refrigerator door is properly closed and that the seal is not damaged
Clean the ventilation grilles (at the front and back) - an obstruction prevents air circulation
Wait 3 to 4 hours after plugging in or restarting, as the appliance takes time to reach the target temperature
Check that the ambient temperature is between +10°C and +43°C (climate class N, SN, ST, T depending on your model)

Temperature Settings:

On this model, the refrigerator is set from 1°C to 7°C (default: 3°C) and the freezer from -15°C to -23°C (default: -18°C). Press the Fridge or Freezer button to adjust.

If the problem persists:

Try the Express Cool function (press and hold the button for 3 seconds) to speed up cooling
Restart the appliance by unplugging it for a few minutes
If the freezer LED blinks after these checks, it indicates a persistent temperature alarm - contact LG service

Question 6

What does it mean when all 4 temperature LEDs of the fridge light up?

Accepted Answer

When all 4 temperature LED indicators of the fridge light up together, it indicates a high temperature alarm condition. According to the manual, the freezer temperature indicator blinks and the audible alarm sounds when the temperature rises problematically, for example during the initial startup or after prolonged door opening.

This is not a malfunction: it is a warning signal. Once the temperature stabilizes (usually within a few hours for an initial startup), the LEDs will normalize according to your set parameter.

How to control the temperature:

Press the Fridge button on the control panel to adjust the temperature
Available temperature: from 1°C to 7°C
Default temperature: 3°C
Each press of the button changes the setting by one notch

Note that the displayed temperature is a target temperature, not the actual temperature inside the appliance. The actual temperature varies depending on the amount of food, the frequency of door openings, and the ambient temperature.

Question 7

How to reinstall the folding shelf of the LG GF-LN700MBL refrigerator?

Accepted Answer

Here’s how to reinstall the folding shelf of your LG GF-LN700MBL:

Installation Steps

Tilt and lift - Tilt the front of the shelf upwards, then lift it straight into position
Guide the hooks - Carefully guide the shelf hooks into the side slots of your refrigerator at the desired height
Start with the left - Install the left side of the shelf first
Then the right side - Use the same method to install the right side of the shelf
Check alignment - Slightly lift the left side, lower the right side, and ensure that the shelf is flat and perfectly level

Important tip: If the hooks do not snap in easily, check that the hooks are properly aligned with the designated slots in the refrigerator wall. A slight back-and-forth movement can help to position them correctly.

Folding function: This shelf can be partially folded by pushing its front half under the back half to store taller items. Pull it forward to return it to its full configuration.

Question 8

How to replace the water filter of the LG GS65WPPK?

Accepted Answer

Water Filter Replacement

The water filter of your LG GS65WPPK should be replaced approximately every 6 months, or according to the filter saturation indicator.

Replacement Procedure:

Unscrew the water filter cap
Pull the water supply tube until a colored line becomes visible
Insert the tube into the new filter and push it all the way in (the colored line should disappear)
Screw the cap back on
Press and hold the water filter reset button for 3 seconds to reset the indicator
Let the water run for about 5 minutes to flush out air and impurities from the system

Replacement Cartridge: Only use the authentic LG ADQ736939 cartridge to ensure the quality of your water and compatibility with your appliance.

Tip: If the water flows slowly or has air bubbles during the first use after replacement, this is normal - continue to let the water run for a few more minutes.

Question 9

Why is my refrigerator not cold enough while the compressor is running?

Accepted Answer

Observed symptom: The refrigerator's compressor is functioning normally, but the appliance is not cooling sufficiently. You notice that the back of the appliance is not as warm as it should be.

This symptom may indicate a problem with the circulation of the refrigerant (cooling gas) rather than an issue with the compressor itself. Before concluding that the compressor is faulty, check the following:

Checks to perform:

Clean the rear ventilation grilles: Dirt or blockage at the condenser (rear coil) prevents proper heat dissipation. Unplug the appliance, wait 30 minutes, then carefully clean the rear grille.
Check air circulation: Ensure that no food or packaging is obstructing the internal ventilation openings. Cold air must circulate freely in all compartments.
Check temperature settings: Make sure the thermostat is not set too high. An incorrect setting can cause the compressor to run without effective cooling.
Inspect door seals: Worn or poorly closed seals allow cold air to escape and force the compressor to work harder without results.

If the problem persists: After these checks, if the back of the refrigerator remains cold and the appliance still does not cool, it is likely that there is a refrigerant leak or a malfunction of the temperature sensor. These issues require professional technical intervention, as they involve the hermetic circuit of the appliance.

Question 10

How to turn on and set up the LG GBB71NSDFN refrigerator?

Accepted Answer

Powering On: After installation, plug the power cord into an outlet (220-240 V, 50 Hz). Then wait 2 to 3 hours before using the appliance to allow the cooling to stabilize completely.

Temperature Settings:

Refrigerator: Press the Fridge Temperature button to adjust the temperature between 1°C and 7°C (default temperature: 3°C).
Freezer: Press the Freezer Temperature button to adjust the temperature between -15°C and -23°C (default temperature: -18°C).

Additional Features:

Express Cool: For quick cooling, hold the button for 3 seconds.
Express Freeze: For quick freezing, hold the button for 3 seconds.
Eco Friendly: Activates energy-saving mode.
Wi-Fi: Connect the appliance via 2.4 GHz to the LG ThinQ app for remote control.
Lock: Hold for 3 seconds to lock all buttons and prevent accidental changes.

User manual LG Refrigerator : user manuals and guides in PDF

Models LG Refrigerator most viewed

Other categories LG

Recent questions about Refrigerator LG