Q: Why does the HOTPOINT ELTB 6M124 EU dishwasher stop after a few seconds with a beeping sound and all the lights on?

When the dishwasher stops immediately after starting with a regular beeping sound and all the lights on, it usually indicates a detection problem that forces the appliance to interrupt the cycle. Priority checks to perform: Check that the door (hatch) is properly closed - A poorly locked door is the most common cause of immediate stop. Ensure it clicks into place correctly. Inspect the wash arms - Rotate both rotating arms to check that they pivot freely. A blocked or obstructed arm by an object can trigger the safety stop. Check the filters - The maintenance guide for the ELTB 6M124 EU mentions 3 filtering elements. Turn the cylindrical filter counterclockwise to remove it and clean it. Never remove the washing pump protection (black part). Check the regenerating salt tank - Ensure that the salt tank cover is not properly closed (this can be detected by the appliance). After these checks: If the problem persists, turn off the appliance using the ON-OFF button, wait about a minute, then turn it back on and select the program again. This restart may reset the sensors. If the stop occurs again, a hardware fault in the sensors or the washing pump may be the cause and would require technical intervention.

Q: How do I start a maintenance cleaning cycle on my washing machine?

Here’s how to start a maintenance cleaning cycle on your HOTPOINT NSWE 965C WS UK N : Auto-Clean Cycle Steps Close the washing machine door Turn the machine on (ON) Press button 1 for 5 seconds to start the Auto-Clean cycle The cycle will start automatically and will last approximately 70 minutes If you wish to stop the cycle before it ends, press the START/PAUSE button Usage Recommendations You can add regular detergent (only 10% of the normal dose for lightly soiled laundry) or a specific cleaning product for machines Run this cycle approximately every 40 wash cycles to keep the internal components in good condition and prevent odors

Q: Where to put the liquid detergent in the HOTPOINT CAWD 129 washing machine?

The liquid detergent is placed in the compartment 1 of the detergent drawer of your HOTPOINT CAWD 129 washing machine. To use the liquid detergent correctly: Pour the liquid detergent just before starting the machine Access the drawer by lifting it and then pulling it towards you to remove it from its housing Fill the compartment without exceeding the indicated limits Maintenance tip: Regularly clean the detergent drawer to avoid blockages and ensure proper functioning of the automatic dosing.

Q: How to change the language of the HOTPOINT BWMD 742 washing machine?

Upon first power on of the HOTPOINT BWMD 742 washing machine, the language selection menu appears automatically. Use the X and Y buttons to scroll through the available languages, then press the Z button to confirm your choice. To change the language after the initial setup : Turn off the machine Press and hold the X, Y, and Z buttons simultaneously until you hear a beep The language selection menu reappears - choose your desired language Your HOTPOINT BWMD 742 offers many languages: French, English, Spanish, Italian, Russian, and many more.

Question 1

Why does the HOTPOINT ELTB 6M124 EU dishwasher stop after a few seconds with a beeping sound and all the lights on?

Accepted Answer

When the dishwasher stops immediately after starting with a regular beeping sound and all the lights on, it usually indicates a detection problem that forces the appliance to interrupt the cycle.

Priority checks to perform:

Check that the door (hatch) is properly closed - A poorly locked door is the most common cause of immediate stop. Ensure it clicks into place correctly.
Inspect the wash arms - Rotate both rotating arms to check that they pivot freely. A blocked or obstructed arm by an object can trigger the safety stop.
Check the filters - The maintenance guide for the ELTB 6M124 EU mentions 3 filtering elements. Turn the cylindrical filter counterclockwise to remove it and clean it. Never remove the washing pump protection (black part).
Check the regenerating salt tank - Ensure that the salt tank cover is not properly closed (this can be detected by the appliance).

After these checks:

If the problem persists, turn off the appliance using the ON-OFF button, wait about a minute, then turn it back on and select the program again. This restart may reset the sensors.

If the stop occurs again, a hardware fault in the sensors or the washing pump may be the cause and would require technical intervention.

Question 2

How to set up a cotton program with soaking and bleaching on a HOTPOINT ECOT7F 129?

Accepted Answer

To wash cotton with soaking (pre-wash) and bleaching on your HOTPOINT ECOT7F 129, you need to use the program 1 “Cotton Pre-wash 90°C”, which is specially designed for extremely dirty laundry and includes a pre-wash/soaking phase.

Steps to follow:

1. Select program 1 “Cotton Pre-wash 90°C”

Maximum load: 7 kg
Temperature: 90°C
This program automatically includes a pre-wash phase

2. Use the detergent drawer correctly:

Compartment 1: Pour in the powder detergent for the pre-wash
Compartment 2: Pour in the powder or liquid detergent for the main wash
Compartment 3: Fabric softener (optional, do not exceed the max line)
Compartment 4: Pour in bleach for bleaching

3. Start the cycle

Important: Bleaching (bleach) only works with programs 2, 3, and 6. However, if you use program 1 (Cotton Pre-wash), the bleach poured into compartment 4 will be treated during the main wash phase. To ensure better bleaching efficiency with soaking, prefer program 6 (Anti-bacterial) at 90°C, which combines soaking and supports bleaching.

Question 3

How do I start a maintenance cleaning cycle on my washing machine?

Accepted Answer

Here’s how to start a maintenance cleaning cycle on your HOTPOINT NSWE 965C WS UK N:

Auto-Clean Cycle Steps

Close the washing machine door
Turn the machine on (ON)
Press button 1 for 5 seconds to start the Auto-Clean cycle
The cycle will start automatically and will last approximately 70 minutes
If you wish to stop the cycle before it ends, press the START/PAUSE button

Usage Recommendations

You can add regular detergent (only 10% of the normal dose for lightly soiled laundry) or a specific cleaning product for machines
Run this cycle approximately every 40 wash cycles to keep the internal components in good condition and prevent odors

Question 4

What are the durations of the different washing programs of the HOTPOINT ELTB 6M124 EU?

Accepted Answer

Here are the exact durations of each washing program of the HOTPOINT ELTB 6M124 EU:

Express 40': 40 minutes (for lightly soiled small laundry)
Soaking: 12 minutes
Auto Normal: 1h30 to 2h30 (duration varies according to the load sensor)
Delicates: 1h40
Auto Intensive: 2h to 3h10 (duration varies according to the load sensor)
Eco: 3h10 (most energy and water-efficient standard program)

The Auto programs (Normal and Intensive) have a variable duration because a special sensor evaluates the degree of soiling of the laundry and automatically adjusts the washing cycle to optimize energy efficiency.

Question 5

How to change the language of the WMUD 10637P washing machine manual?

Accepted Answer

The WMUD 10637P washing machine does not offer a language selection on its interface. However, if you are looking for the user manual in another language, you can easily request it.

On this notice page, click on the Other language? button at the top of the document. You will then be able to:

Select your preferred language (French, German, Dutch, Spanish, Italian, Portuguese, Polish, Russian, Arabic, Turkish, Japanese, Chinese, Korean, and many others)
Provide your email address
Receive a translated version of the manual within a few days

This translation will allow you to consult the entire user guide in your language.

Question 6

Where to put the liquid detergent in the HOTPOINT CAWD 129 washing machine?

Accepted Answer

The liquid detergent is placed in the compartment 1 of the detergent drawer of your HOTPOINT CAWD 129 washing machine.

To use the liquid detergent correctly:

Pour the liquid detergent just before starting the machine
Access the drawer by lifting it and then pulling it towards you to remove it from its housing
Fill the compartment without exceeding the indicated limits

Maintenance tip: Regularly clean the detergent drawer to avoid blockages and ensure proper functioning of the automatic dosing.

Question 7

How to change the language of the HOTPOINT BWMD 742 washing machine?

Accepted Answer

Upon first power on of the HOTPOINT BWMD 742 washing machine, the language selection menu appears automatically. Use the X and Y buttons to scroll through the available languages, then press the Z button to confirm your choice.

To change the language after the initial setup:

Turn off the machine
Press and hold the X, Y, and Z buttons simultaneously until you hear a beep
The language selection menu reappears - choose your desired language

Your HOTPOINT BWMD 742 offers many languages: French, English, Spanish, Italian, Russian, and many more.

Question 8

How to properly install a HOTPOINT WMG 821 B EX.M washing machine?

Accepted Answer

To properly install your HOTPOINT WMG 821 B EX.M washing machine, with an 8 kg capacity and a 54-liter drum, carefully follow these essential steps to ensure safe and optimal operation.

Unpacking and removing transport elements

Remove the appliance from its packaging and check for any damage. If any damage is found, contact the retailer before continuing with the installation.
Remove the 3 protective screws located at the back of the machine (transport parts), as well as the rubber washer and its corresponding spacer.
Plug the holes with the provided plastic caps and keep all these parts in case of future relocation of the machine.

Leveling the machine

Install the washing machine on a flat and sturdy floor, without pushing it against walls, furniture, or other appliances.
Adjust the front feet to compensate for any unevenness in the floor. The tilt angle, measured against the worktop, should not exceed 2 degrees.
Proper leveling provides stability to the machine, limits vibrations, noise, and movement during operation. If the machine is placed on carpet or rug, adjust the feet to allow sufficient ventilation space under the appliance.

Connecting to cold water

Connect the water inlet hose to a cold water tap with a 3/4 gas thread. Before connecting, let the water run until it is perfectly clear.
Connect the other end of the hose to the water inlet located at the top right of the back of the machine.
Ensure that the hose is not kinked or crushed. The water pressure should be between 0.05 MPa (0.5 bar) minimum and 1 MPa (10 bars) maximum.
Never use second-hand hoses; only use those provided with the machine. If the hose is too short, contact a specialized retailer or a certified technician.

Water drainage

Connect the drain hose without bending it to a drainage pipe or wall drain, positioned between 65 and 100 cm above the floor.
You can also place the hose over the edge of a sink or bathtub by securing the provided guide to the tap. The free end of the hose should never be submerged in water.
Hose extensions are not recommended. If necessary, the extension must have the same diameter and not exceed 150 cm in length.

Electrical connection

Before plugging in the appliance, ensure that the socket is grounded and complies with legal standards, that its maximum load supports the machine's power (see the technical plate), and that the supply voltage matches the specifications.
The machine must not be installed outdoors under any circumstances, even if protected, as it may be damaged by rain and storms.
Never use an extension cord or multiple sockets. The power cable must not be bent or compressed. After installation, the electrical socket should remain easily accessible.

First wash cycle

Once the installation is complete, run a full cycle with detergent but without laundry by selecting the “Auto Cleaning” program. This automatic cycle lasts about 70 minutes and prepares the machine. You can activate it by pressing buttons A and B simultaneously for 5 seconds.

Question 9

What is the duration of the "6 Buonanotte" program on the HOTPOINT ECO8L 1252 EU.M washing machine?

Accepted Answer

The "6 Buonanotte" program of the HOTPOINT ECO8L 1252 EU.M washing machine is designed for gentle and quiet washing, ideal for use during the night. This cycle has a duration of approximately 6 hours.

This long washing time allows for effective cleaning while reducing energy consumption and noise, making it perfect for nighttime use without disturbing sleep.

Question 10

What does the error code with the fixed 40° and * indicators and the flashing cycle indicators as well as the on/off indicator mean on the HOTPOINT AQ8L 292 U washing machine?

Accepted Answer

The error code indicated by the fixed 40° and * indicators, accompanied by the flashing cycle indicators and the on/off indicator on your HOTPOINT AQ8L 292 U washing machine, signals a problem with water drainage. These flashing indicators along with the ON/OFF light constitute a specific system alert signal for your machine. This malfunction prevents water from draining properly from the drum, which may be due to a blockage in the drainage circuit or a pump failure.

First, check the pump filter. Located at the bottom of the machine at the front (under the protective panel), this filter may be clogged with lint, coins, sand, or other debris that prevents water from draining. Open the small access flap, empty the residual water into a container, then gently unscrew the filter counterclockwise. Rinse it under running water until it is completely clean and reinstall it properly.

Carefully inspect the drainage hose. Check that the hose is not bent, crushed, or trapped by furniture. Also, ensure that its end is not submerged in the drainage siphon or pushed too deeply, as this can create an air blockage that obstructs flow. The correct height is generally between 65 and 100 cm from the floor. Also check that the hose is not clogged: pour water manually from the outside to verify that water flows well.

During the drainage cycle, listen to the operation of the pump. You should hear a characteristic operating noise. The absence of noise may indicate that the pump is not functioning properly or that there is a blockage upstream. If you hear no sound, the intervention of an authorized technician will likely be necessary.

Reduce the laundry load if you usually fill the drum to the brim. Overloading can prevent proper water circulation and hinder drainage. Try running a cycle with a reduced amount to test.

Restart the device by resetting it. Turn off the washing machine, unplug it from the socket for 1 to 2 minutes, then power it back on. Start a drain or spin cycle to see if the problem disappears. Sometimes, an electronic reset resolves temporary anomalies.

If after these checks the error code persists or appears again, contact the authorized HOTPOINT technical support service or an authorized repair technician, as the drainage pump or the electronic control system may have a defect requiring professional repair.

User manual HOTPOINT Washing machine : user manuals and guides in PDF

Models HOTPOINT Washing machine most viewed

Other categories HOTPOINT

Recent questions about Washing machine HOTPOINT