Question 1

Why is the grinder not grinding well even though the blade is turning?

Accepted Answer

If the blade is turning but your grinder is not grinding or grinding poorly, it is usually due to dull or damaged blades. Here’s how to check and resolve:

Check the condition of the blades

Stop the grinder and wait for the blade to come to a complete stop
Open access to the cutting disc (reference 113079)
Inspect the blades for wear or damage

The blades should be replaced regularly to achieve optimal grinding results, states the technical manual. Even slightly dull blades significantly reduce efficiency.

Replace or reverse the blades

Unscrew the central locking bolt
Remove the counter-blade assembly
You can first reverse the blades (invert their orientation) to use the other side - this is a temporary solution
If too worn, replace them with new blades using M8x10 steel screws

Check for possible blockage

If the blades appear to be in good condition, a wet debris may be blocking the cutting mechanism. Completely clean the cutting disc and counter-blade of any residues.

Once the blades are in good condition, your grinder will regain its cutting performance.

Question 2

How to check and maintain the cutting blades of the Easy Crush MH 2810?

Accepted Answer

To check the condition of your blades and keep them in good working order:

Before any intervention

Unplug the grinder and disconnect it from the power outlet
Wait for the device to cool down

Checking the blades

Unscrew the locking screw and remove the top part of the grinder
Observe the condition of the two blades: if they are dull on only one side, you can flip them over
If they are dull or damaged on both sides, they need to be replaced

Replacing the blades

Loosen the three M8 nuts holding the counter-blade in place
Remove the M8x10 countersunk screws securing the blades
Always replace the blades in pairs to balance the device (part reference: 113079)
Tighten all screws securely
Reassemble the top part

Important: The blades should be checked regularly and replaced as soon as they no longer cut sharply, in order to achieve optimal cutting results and avoid overloading the motor.

Question 3

Why does the shredder not pull in branches and shred them?

Accepted Answer

If your AL-KO Easy Crush MH 2810 does not pull in branches and shred them, several causes are possible. Here’s how to identify them:

1. Check the material capacity

This model shreds branches up to 40 mm in diameter maximum. If you attempt to process thicker branches, the motor will not be able to pull them in or cut them. First, test with thinner branches.

2. Inspect the blades

The blades must be regularly replaced for optimal shredding results. Worn or dull blades will not be able to pull in or shred effectively. Check the condition of the cutting disc blades and replace them if necessary (the manual indicates the replacement procedure).

3. Clean the residues

Internal clogging (wet residues or stuck twigs) can prevent pulling in. Completely turn off the device and clean the passages with a soft brush. Never use a high-pressure cleaner.

4. Respect the operating cycle

The motor is designed for 40 seconds of maximum load, followed by 60 seconds of rest. Continuous operation under overload causes the motor to automatically shut down due to thermal protection. Allow it to cool for 5 minutes, then restart the device.

5. Check the power supply and motor

Ensure that the power cord is properly plugged in and that the device starts. If the motor does not run at all, consult the troubleshooting table in the manual to check the connections and fuses.

If the problem persists after these checks, the blades or the drive system may be damaged and require after-sales service.

Question 4

Why does the AL-KO Easy Crush MH 2810 shredder frequently stop at the slightest difficulty?

Accepted Answer

The AL-KO Easy Crush MH 2810 shredder is equipped with a motor protection system that causes the device to automatically stop in case of overload. This behavior is normal and designed to protect the motor from damage.

Operation of the safety system

Motor protection switch: This device automatically cuts off the power when the motor is overloaded.
After stopping, you need to wait about 5 minutes for the motor to cool down before you can reset the switch and restart the device.
The MH 2810 is designed for intermittent operation: 40 seconds of work at full load, followed by a pause of about 60 seconds.

Tips to avoid frequent stops

Work in small sessions, allowing breaks for the motor to cool down.
Use materials with a maximum diameter of 40 mm, thinner if possible, to reduce the load.
If the circuit breaker trips often, let the motor cool down longer before restarting.
If problems persist, have the device checked by a professional.

This protection system is a normal and important feature to ensure the durability and safety of your AL-KO Easy Crush MH 2810 shredder.

User manual AL-KO Mechanical chipper : user manuals and guides in PDF

Models AL-KO Mechanical chipper most viewed

Other categories AL-KO

Recent questions about Mechanical chipper AL-KO